SAE AS 683 : 2012
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
INSTALLATION PROCEDURES AND TORQUES FOR FLUID CONNECTIONS
Hardcopy , PDF
31-10-2019
English
01-01-2012
FOREWORD
1. SCOPE
2. APPLICABLE DOCUMENTS
3. CONE END CONNECTIONS FOR FLARED TUBE AND BRAZED FERRULE
4. BOSS END CONNECTIONS, POSITIONED TYPE, WITH BACK-UP RING
5. BOSS END CONNECTIONS, POSITIONED TYPE, WITHOUT BACK-UP RING
6. BOSS END CONNECTIONS, NON-POSITIONED TYPE
7. BULKHEAD CONNECTIONS
8. REFERENCE RING SEAL DATA
9. TORQUE VALUES
10. ADAPTERS
11. NOTES
Specifies the following: - Paragraph 3 - Cone end connections for flared tube and brazed ferrule, with and without gasket. - Paragraph 4 - Boss end connections, positioned type, with back-up ring. - Paragraph 5 - Boss end connections, positioned type, without back-up ring. - Paragraph 6 - Boss end connections, non-positioned type. - Paragraph 7 - Bulkhead connections.
Committee |
E-25
|
DocumentType |
Standard
|
Pages |
13
|
PublisherName |
SAE International
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
SAE AIR 5426 : 2013 | FITTING AND FITTING ASSEMBLY SELECTION, INSTALLATION, INSPECTION AND MAINTENANCE OF |
SAE ARP 994 : 2016 | DESIGN OF TUBING INSTALLATIONS FOR AEROSPACE HYDRAULIC SYSTEMS |
MS9194 Revision C:2010 | Elbow, Tube - SAE-AMS5646, Boss, 90 Degrees |
SAE AS 5160 : 2013 | FITTING, BOLT, FLARED |
SAE AS 4396 : 2013 | FITTING END, BULKHEAD, FLARED TUBE CONNECTION, DESIGN STANDARD |
SAE AS 3578 : 2012 | PACKING, PREFORMED - O-RING SEAL AMS 7271 |
SAE AS 5406 : 2015 | FITTING, UNION, TUBE, .375 BULKHEAD |
MS9095 Revision B:2010 | NIPPLE, TUBE - ALUMINUM, BOSS |
SAE AS 9058 : 2015 | RING - BACK-UP, BOSS CONNECTION, AMS3652, AMS3656, AMS3660, AMS3667 |
SAE AS 567 : 2015 | SAFETY CABLE, SAFETY WIRE, KEY WASHERS, AND COTTER PINS FOR PROPULSION SYSTEMS, GENERAL PRACTICES FOR USE OF |
NAS1149:2014 | WASHER, FLAT |
SAE AS 9902 : 2010 | PLUG, MACHINE THREAD DRILLED, PREFORMED PACKING, AS8879 THREAD (UNS S34700) |
SAE AS 930 : 2013 | FITTING END - STRAIGHT THREAD, PORT CONNECTION, DESIGN STANDARD |
SAE ARP 573 : 2012 | SILVER, COPPER AND NICKEL ALLOY BRAZED JOINTS FOR AEROSPACE PROPULSION SYSTEMS |
SAE AS 5176 : 2015 | FITTING, SLEEVE, FLARED |
MIL-PRF-7808 Revision L:1997 | LUBRICATING OIL, AIRCRAFT TURBINE ENGINE, SYNTHETIC BASE |
SAE AMS G 4343 : 2012 | GREASE, PNEUMATIC SYSTEM |
MIL-PRF-5606 Revision H:2002 | HYDRAULIC FLUID, PETROLEUM BASE; AIRCRAFT, MISSILE, AND ORDNANCE |
SAE AMS 7276H : 2011 | RUBBER: FLUOROCARBON (FKM) HIGH-TEMPERATURE-FLUID RESISTANT LOW COMPRESSION SET FOR SEALS IN FUEL SYSTEMS AND SPECIFIC ENGINE OIL SYSTEMS |
SAE AS 5161 : 2013 | FITTING, BOLT, FLUID PASSAGE |
SAE AS 3208 : 1976 | PACKING, PREFORMED - AMS 7276 - SEAL |
SAE AS 4395 : 2013 | FITTING END, FLARED, TUBE CONNECTION, DESIGN STANDARD |
SAE AS 3551 : 2012 | PACKING, PREFORMED - O-RING SEAL, AMS 7272 |
SAE AS 1038 : 2015 | FITTING, ELBOW, 90 DEGREES, STANDARD AND REDUCER, BULKHEAD, FLARED |
MS9196 Revision C:2015 | TEE, TUBE - SAE-AMS5646, BOSS |
SAE AS 9385 : 2012 | PACKING, PREFORMED, AMS 7267, 0-RING |
SAE AS 1039 : 2015 | FITTING, TEE, STANDARD AND REDUCER, BULKHEAD ON SIDE, FLARED |
MS9195 Revision B:2010 | ELBOW, TUBE - SAE-AMS5639, BOSS, 45 DEGREES |
SAE AS 4330 : 2014 | TUBING, FLARED, STANDARD DIMENSIONS FOR, DESIGN STANDARD |
MIL-PRF-87257 Revision C:2017 | HYDRAULIC FLUID, FIRE RESISTANT, LOW TEMPERATURE, SYNTHETIC HYDROCARBON BASE, AIRCRAFT AND MISSILE |
SAE AS 33583 : 2015 | TUBING END DOUBLE FLARE, STANDARD DIMENSIONS FOR |
MS9198 Revision D:2010 | NUT, TUBE COUPLING-CRES SAE-AMS5646 |
SAE AS 3282 : 2014 | GASKET - 37 DEGREES FLARED TUBE FITTING, NICKEL, AMS 5553 |
VV-P-236 Revision A:1977 | PETROLATUM, TECHNICAL |
SAE AS 1078 : 2015 | FITTING END, FLARED TUBE CONNECTION, EXTENDED THREAD, DESIGN STANDARD |
SAE AS 8879 : 2004 | SCREW THREADS - UNJ PROFILE, INCH CONTROLLED RADIUS ROOT WITH INCREASED MINOR DIAMETER |
SAE AS 9966 : 2012 | PACKING, PREFORMED - AMS 7273, SEAL |
SAE AS 90991 : 2013 | NUT, HEXAGON, DRILLED, BOSS CONNECTION, ALUMINUM - UNS A92024 |
MS9953 Base Document:1970 | Plug, Machine Thread - Ams 4121, Preformed Packing Mil-S-8879 Thread |
MS9954 Base Document:1970 | PLUG MACHINE THREAD DRILLED AMS 4121 PREFORMED PACKING MIL-S-8879 THREAD |
MS9015 Revision B:1974 | PLUG, MACHINE THREADED "O" RING SEAL |
SAE AS 92001 : 2011 | NUT, HEXAGON, DRILLED, BOSS CONNECTION, ALUMINIUM - UNS A92014 |
MS9483 Revision C:2010 | FERRULE, BRAZING, TUBE FITTING - CRES SAE-AMS5646, STRAIGHT |
SAE AS 9201 : 2007 | NUT, PLAIN, HEXAGON, BOSS CONNECTION, SILVER PLATED, 347 CRES UNS S34700 |
MIL-PRF-83282 Revision D:1997 | HYDRAULIC FLUID, FIRE RESISTANT, SYNTHETIC HYDROCARBON BASE, METRIC, NATO CODE NUMBER H-537 |
MS9193 Revision A:2010 | NIPPLE, TUBE - SAE-AMS5639, BOSS |
SAE AS 5174 : 2015 | FITTING, UNION AND REDUCER, FLARED |
SAE AS 91001 : 2012 | NUT, HEXAGON, DRILLED, BOSS CONNECTION, CRES - UNS S30400 |
SAE AS 3074 : 2014 | GASKET - 37 DEGREES FLARED TUBE FITTING, NICKEL, AMS 5553 |
MS9096 Revision B:1972 | Elbow, Tube - AMS 4135, Boss, 90 DEG. |
MS9197 Revision D:2010 | Nut, Tube Coupling-CRES SAE-AMS5646, Silver Plate |
MS9097 Revision A:1962 | Elbow, Tube - AMS 4135, Boss, 45 DEG. |
SAE AS 5202 : 2005 | PORT OR FITTING END, INTERNAL STRAIGHT THREAD, DESIGN STANDARD |
SAE AS 5175 : 2017 | NUT, COUPLING, FLARED |
SAE AS 3075 : 2014 | GASKET - 37 DEGREES FLARED TUBE FITTING, NICKEL, AMS 5553 |
MS9901 Base Document:1970 | PLUG MACHINE THREAD AMS 5646 PREFORMED PACKING MIL-S-8879 THREAD |
SAE AS 1171 : 2012 | BOSS - FLUID CONNECTION, INTERNAL STRAIGHT THREAD, SHALLOW TAP |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.