AS/NZS 2290.1:2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Electrical equipment for coal mines - Introduction, inspection and maintenance For hazardous areas
Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users
10-20-2021
English
02-11-2014
This Standard sets out requirements for the inspection and maintenance of electrical equipment designed for use in hazardous areas in and around underground coal mines.
This Standard sets out requirements for the inspection and maintenance of electrical equipment designed for use in hazardous areas in and around underground coal mines. Section 2 provides general requirements that are fundamental to the safe use of electrical equipment in hazardous areas. Section 3 provides specific requirements for each type of explosion-protection technique.This Standard is intended to be applied where there is a potential risk due to the presence of explosive gas, dust mixtures and combustible dust layers. It does not apply to - (a) surface infrastructure, typically Group II or Group III classified areas, other than gas drainage and borehole dewatering areas that could negatively impact on an underground mine workings;(b) areas where a risk can arise due to the presence of hybrid mixtures;(c) areas where small quantities of flammable materials are introduced for maintenance purposes; or(d) shotfiring activities and associated equipment.This Standard does not include - (i) electrical installation and inspection requirements not directly associated with an explosion-protection technique;(ii) the regulatory compliance assessment of electrical equipment; or(iii) the permanent repair, reclamation and overhaul of explosion protected equipment.
Committee |
EL-023
|
DocumentType |
Standard
|
ISBN |
978 1 74342 661 6
|
Pages |
55
|
PublisherName |
Standards Australia
|
Status |
Superseded
|
SupersededBy | |
Supersedes | |
UnderRevision |
Originated in Australia as AS 2290.1—1979.Previous edition AS/NZS 2290.1:2005.Fourth edition 2014. Originated in Australia as AS 2290.1-1979. Previous edition AS/NZS 2290.1:2005. Fourth edition 2014.
AS/NZS 60079.26:2007 | Explosive atmospheres Equipment with equipment protection level (EPL) Ga |
AS/NZS 1299:2009 | Electrical equipment for mines and quarries - Explosion-protected three-phase restrained plugs and receptacles for working voltages up to and including 3.3 kV (Reconfirmed 2020) |
AS/NZS 4871.3:2010 | Electrical equipment for mines and quarries Substations |
AS/NZS 4871.2:2010 | Electrical equipment for mines and quarries Distribution, control and auxiliary equipment |
AS 61508.3-2011 | Functional safety of electrical/electronic/programmable electronic safety-related systems Software requirements (Reconfirmed 2023) |
AS/NZS 3800:2012 | Electrical equipment for explosive atmospheres - Repair and overhaul |
MP 87.2:2007 | Australian/New Zealand Certification Scheme for explosion-protected electrical equipment (ANZEx Scheme) Recognized Service Facilities Program - Basic rules and procedures |
AS/NZS 1802:2003 | Electric cables - Reeling and trailing - For underground coal mining purposes |
AS/NZS 60079.2:2007 | Explosive atmospheres Equipment protection by pressurized enclosure 'p' |
AS/NZS 3000:2007 | Electrical installations (known as the Australian/New Zealand Wiring Rules) |
HB 239:2011 | Guidance on the repair and overhaul of electrical equipment for explosive atmospheres |
AS/NZS 1972:2006 | Electric cables - Underground coal mines - Other than reeling and trailing (Reconfirmed 2020) |
AS 61508.5-2011 | Functional safety of electrical/electronic/programmable electronic safety-related systems Examples of methods for the determination of safety integrity levels (Reconfirmed 2023) |
AS/NZS 60079.18:2011 | Explosive atmospheres Equipment protection by encapsulation 'm' |
AS 61508.0-2006 | Functional safety of electrical/electronic/programmable electronic safety-related systems Functional safety and AS 61508 (Reconfirmed 2015) |
AS/NZS 60079.7:2006 | Explosive atmospheres Equipment protection by increased safety 'e' |
AS/NZS 1300:2009 | Electrical equipment for mines and quarries - Bolted explosion-protected three-phase cable coupling devices (Reconfirmed 2020) |
AS/NZS 4871.5:2010 | Electrical equipment for mines and quarries Battery powered electrical mobile machines |
AS 61508.7-2011 | Functional safety of electrical/electronic/programmable electronic safety-related systems Overview of techniques and measures (Reconfirmed 2023) |
AS/NZS 60079.6:2007 | Explosive atmospheres Equipment protection by oil immersion 'o' |
AS/NZS 4801:2001 | Occupational health and safety management systems - Specification with guidance for use |
AS/NZS ISO 31000:2009 | Risk management - Principles and guidelines |
HB 13-2007 | Electrical equipment for hazardous areas |
HB 242-2007 | High voltage mining equipment for use underground (Reconfirmed 2019) |
AS/NZS 4871.6:2013 | Electrical equipment for mines and quarries Diesel powered machinery and ancillary equipment |
AS/NZS 60079.1:2007 | Explosive atmospheres Equipment protection by flameproof enclosures 'd' |
AS/NZS 60079.5:2007 | Explosive atmospheres Equipment protection by powdered filling 'q' |
AS/NZS 60079.11:2011 | Explosive atmospheres Equipment protection by intrinsic safety ‘i’ (Reconfirmed 2022) |
AS/NZS 4761.2:2008 | Competencies for working with electrical equipment for hazardous areas (EEHA) Guide to assessing competency |
AS/NZS 60079.14:2009 | Explosive atmospheres Electrical installations design, selection and erection (IEC 60079-14, Ed. 4.0 (2007) MOD) |
AS 61508.1-2011 | Functional safety of electrical/electronic/programmable electronic safety-related systems General requirements (Reconfirmed 2023) |
AS 61508.2-2011 | Functional safety of electrical/electronic/programmable electronic safety-related systems Requirements for electrical/electronic/programmable electronic safety-related systems (Reconfirmed 2023) |
AS/NZS 4761.1:2008 | Competencies for working with electrical equipment for hazardous areas (EEHA) Competency Standards |
AS/NZS 4871.1:2012 | Electrical equipment for mines and quarries General requirements |
AS 61508 Supp1-2012 | Functional safety of electrical/electronic/programmable electronic safety-related systems, Supplement 1: Commented version (Supplement to AS 61508 series) (Reconfirmed 2023) |
AS/NZS 4871.4:2010 | Electrical equipment for mines and quarries Mains powered electrical mobile machines |
AS 61508.6-2011 | Functional safety of electrical/electronic/programmable electronic safety-related systems Guidelines on the application of IEC 61508-2 and IEC 61508-3 (Reconfirmed 2023) |
MP 87.1:2008 | Australian/New Zealand Certification Scheme for explosion-protected electrical equipment (ANZEx Scheme) Product Certification Program - Basic rules and procedures |
AS/NZS 1747:2003 | Reeling, trailing and feeder cables used for mining - Repair, testing and fitting of accessories (Reconfirmed 2020) |
AS/NZS 60079.0:2012 | Explosive atmospheres Equipment - General requirements |
AS 61508.4-2011 | Functional safety of electrical/electronic/programmable electronic safety-related systems Definitions and abbreviations (Reconfirmed 2023) |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.