14/30297462 DC : 0
NA
Status of Standard is Unknown
BS EN 15015 - PLASTICS PIPING SYSTEMS - HOT AND COLD WATER PIPING COMPONENTS - REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR PIPES AND FITTINGS
Hardcopy , PDF
English
Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions and
abbreviations
4 Product characteristics
5 Testing, assessment and
sampling methods
6 Assessment and verification of
the constancy of performance (AVCP)
Annex A (normative) - Overall service
(design) coefficient
Annex ZA (informative) - Clauses of this
European Standard addressing
the provisions of the EU
Construction Products
Regulation
Bibliography
BS EN 15015
Committee |
PRI/88/2
|
DocumentType |
Draft
|
Pages |
59
|
PublisherName |
British Standards Institution
|
Status |
NA
|
Standards | Relationship |
PREN 15015 : DRAFT 2014 | Identical |
EN ISO 3126:2005 | Plastics piping systems - Plastics components - Determination of dimensions (ISO 3126:2005) |
EN ISO 15875-2:2003/A1:2007 | PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - CROSSLINKED POLYETHYLENE (PE-X) - PART 2: PIPES |
EN 12293:1999 | Plastics piping systems - Thermoplastics pipes and fittings for hot and cold water - Test method for the resistance of mounted assemblies to temperature cycling |
EN 681-1:1996/A3:2005 | ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 1: VULCANIZED RUBBER |
EN ISO 15877-2:2009/A1:2010 | PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - CHLORINATED POLY(VINYL CHLORIDE) (PVC-C) - PART 2: PIPES |
EN ISO 15875-3:2003 | Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 3: Fittings (ISO 15875-3:2003) |
ISO/TS 15875-7:2003 | Plastics piping systems for hot and cold water installations Crosslinked polyethylene (PE-X) Part 7: Guidance for the assessment of conformity |
ISO 1167-2:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces |
EN ISO 15877-3:2009/A1:2010 | PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - CHLORINATED POLY(VINYL CHLORIDE) (PVC-C) - PART 3: FITTINGS |
CEN ISO/TS 22391-7:2011 | Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 7: Guidance for the assessment of conformity (ISO/TS 22391-7:2011) |
EN ISO 15876-2:2017 | Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 2: Pipes (ISO 15876-2:2017) |
EN ISO 1167-2:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 2: Preparation of pipe test pieces (ISO 1167-2:2006) |
EN ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 1: General method (ISO 1167-1:2006) |
ISO 1167-4:2007 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 4: Preparation of assemblies |
ISO 9080:2012 | Plastics piping and ducting systems — Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation |
ISO 17456:2006 | Plastics piping systems Multilayer pipes Determination of long-term strength |
CEN ISO/TS 15875-7:2003 | Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 7: Guidance for the assessment of conformity (ISO/TS 15875-7:2003) |
EN ISO 22391-3:2009 | Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 3: Fittings (ISO 22391-3:2009) |
EN ISO 21003-2:2008/A1:2011 | Multilayer piping systems for hot and cold water installations inside buildings - Part 2: Pipes - Amendment 1 (ISO 21003-2:2008/Amd 1:2011) |
EN ISO 9080:2012 | Plastics piping and ducting systems - Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation (ISO 9080:2012) |
ISO/TS 15876-7:2003 | Plastics piping systems for hot and cold water installations Polybutylene (PB) Part 7: Guidance for the assessment of conformity |
EN 13823:2010+A1:2014 | REACTION TO FIRE TESTS FOR BUILDING PRODUCTS - BUILDING PRODUCTS EXCLUDING FLOORINGS EXPOSED TO THE THERMAL ATTACK BY A SINGLE BURNING ITEM |
ISO 3126:2005 | Plastics piping systems Plastics components Determination of dimensions |
EN ISO 13760:1998 | Plastics pipes for the conveyance of fluids under pressure - Miner's rule - Calculation method for cumulative damage (ISO 13760:1998) |
EN ISO 1167-4:2007 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 4: Preparation of assemblies (ISO 1167-4:2007) |
EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
ISO/TS 15877-7:2009 | Plastics piping systems for hot and cold water installations Chlorinated poly(vinyl chloride) (PVC-C) Part 7: Guidance for the assessment of conformity |
EN ISO/TS 15876-7 : 2003 | PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - POLYBUTYLENE (PB) - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
EN ISO 15876-3:2017 | Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 3: Fittings (ISO 15876-3:2017) |
EN 727:1994 | Plastics piping and ducting systems - Thermoplastics pipes and fittings - Determination of Vicat softening temperature (VST) |
ISO 1167-3:2007 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 3: Preparation of components |
ISO 21003-2:2008 | Multilayer piping systems for hot and cold water installations inside buildings — Part 2: Pipes |
ISO 10508:2006 | Plastics piping systems for hot and cold water installations Guidance for classification and design |
ISO 9001:2015 | Quality management systems — Requirements |
EN ISO 22391-2:2009 | Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 2: Pipes (ISO 22391-2:2009) |
ISO/TS 21003-7:2008 | Multilayer piping systems for hot and cold water installations inside buildings Part 7: Guidance for the assessment of conformity |
ISO/TS 22391-7:2011 | Plastics piping systems for hot and cold water installations Polyethylene of raised temperature resistance (PE-RT) Part 7: Guidance for the assessment of conformity |
EN ISO/TS 15874-7 : 2003 | PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - POLYPROPYLENE (PP) - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
EN ISO 1133:2005 | PLASTICS - DETERMINATION OF THE MELT MASS-FLOW RATE (MFR) AND THE MELT VOLUME-FLOW RATE (MVR) OF THE THERMOPLASTICS |
ISO 13760:1998 | Plastics pipes for the conveyance of fluids under pressure — Miner's rule — Calculation method for cumulative damage |
CEN ISO/TS 21003-7:2008/A1:2010 | MULTILAYER PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS INSIDE BUILDINGS - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
EN ISO 15874-2:2013 | Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 2: Pipes (ISO 15874-2:2013) |
ISO/TS 15874-7:2003 | Plastics piping systems for hot and cold water installations Polypropylene (PP) Part 7: Guidance for the assessment of conformity |
ISO 1133:2005 | Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics |
CEN/TS 12201-7:2014 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 7: Guidance for the assessment of conformity |
CEN ISO/TS 15877-7:2009 | Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 7: Guidance for the assessment of conformity (ISO/TS 15877-7:2009) |
EN ISO 1167-3:2007 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 3: Preparation of components (ISO 1167-3:2007) |
EN ISO 15874-3:2013 | Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 3: Fittings (ISO 15874-3:2013) |
ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method |
EN 16000:2010 | Plastics piping systems - Systems within the building structure - Mounting and fixing of components in the test apparatus to thermal attack by a single burning item |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.