ANSI INCITS 362 : 2002
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
SCSI PARALLEL INTERFACE-4 (SPI-4)
Hardcopy , PDF
07-23-2013
English
01-01-2002
Foreword
Introduction
1 Scope
2 Normative references
2.1 Normative references
2.2 Approved references
2.3 References under development
2.4 Other references
3 Definitions, symbols, abbreviations, and conventions
3.1 Definitions
3.2 Symbols and abbreviations
3.3 Keywords
3.4 Conventions
3.5 Notation for Procedures and Functions
4 General
4.1 General overview
4.2 Cables, connectors, signals, transceivers
4.3 Physical architecture of bus segment
4.4 Driver-receiver connections
4.5 Physical topology details and definitions
4.6 Bus segment loading
4.7 Termination requirements
4.8 SCSI device Addressing
4.9 Clocking methods for data transfers
4.10 Paced transfer on a SCSI bus
4.11 Data transfers
4.12 Negotiation
4.13 Protocol
5 SCSI parallel interface connectors
5.1 SCSI parallel interface connectors overview
5.2 Nonshielded connector
5.3 Shielded connector
5.4 Connector contact assignments
6 SCSI bus segment interconnect
6.1 SCSI bus segment interconnect overview
6.2 SCSI bus segment cables
6.3 Interconnect characteristics for signals
6.4 Decoupling characteristics for TERMPWR lines
6.5 Connection requirements for RESERVED lines
6.6 Cables used with SE transceivers
6.7 SE ground offset
6.8 Cables used with LVD transceivers
6.9 LVD stub length and spacing
7 SCSI parallel interface electrical characteristics
7.1 SCSI parallel interface electrical characteristics overview
7.2 SE alternative
7.3 LVD alternative
7.4 LVD/MSE multimode alternative
7.5 Terminator power
8 SCSI bus signals
8.1 SCSI bus signals overview
8.2 Signal descriptions
8.3 Signal states
8.4 OR-tied signals
8.5 Signal sources
9 SCSI parallel bus timing
9.1 SCSI parallel bus timing values
9.2 Timing description
9.3 Measurement points
9.4 Receiver Masks
9.5 Timing parameters
9.6 Setup and hold timings
10 SCSI bus phases
10.1 SCSI bus phases overview
10.2 BUS FREE phase
10.3 Expected and unexpected bus free phases
10.4 Arbitration
10.5 SELECTION phase
10.6 RESELECTION phase
10.7 Information transfer phases
10.8 COMMAND phase
10.9 DATA phase
10.10 STATUS phase
10.11 MESSAGE phase
10.12 Signal restrictions between phases
11 DATA BUS protection
11.1 DATA BUS protection overview
11.2 ST DATA BUS protection using parity
11.3 DT DATA BUS protection using CRC
12 SCSI bus conditions
12.1 SCSI bus conditions overview
12.2 Attention condition
12.3 Bus reset condition
12.4 Hard reset
12.5 Reset events
13 SCSI bus phase sequences
13.1 SCSI bus phase sequences overview
13.2 Phase sequences with information units disabled
13.3 Phase sequences with information unit enabled
14 SPI information units
14.1 SPI information unit overview
14.2 Information unit transfer logical operations
14.3 SPI information units
15 SCSI pointers
16 SCSI messages
16.1 SCSI messages overview
16.2 Message protocols and formats
16.3 Link control messages
16.4 Task attribute messages
16.5 Task management messages
17 Command processing considerations and exception conditions
17.1 Command processing considerations and exception conditions
17.2 Asynchronous event notification
17.3 Incorrect initiator connection
17.4 Unexpected RESELECTION phase
18 SCSI management features for the SCSI parallel interface
18.1 SCSI mode parameters
19 SCSI parallel interface services
19.1 SCSI parallel interface services overview
19.2 Procedure objects
19.3 Application client SCSI command services
19.4 Device server SCSI command services
19.5 Task management services
Annexes
A Additional requirements for LVD SCSI drivers and receivers
B SCSI bus fairness
C Nonshielded connector alternative 4
D Removal and insertion of SCSI devices
E SCSI bulk cable performance testing
F Simple expander requirements
G Expander Communication Protocol
H Interconnecting bus segments of different widths
I Transmission line considerations for SE fast-20 data transfer rates
J Measuring SE pin capacitance
K SCSI ICONS
L Backplane construction guidelines
M SPI-4 to SCSI-2 terminology mapping
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.