Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

14/30256269 DC : 0

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

BS EN ISO 24817 - PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - COMPOSITE REPAIRS FOR PIPEWORK - QUALIFICATION AND DESIGN, INSTALLATION, TESTING AND INSPECTION
Available format(s)

Hardcopy , PDF

Superseded date

31-08-2015

Language(s)

English

1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Applications
6 Summary of key issues
7 Qualification and design
8 Installation
9 Testing and inspection
10 System testing
11 Decommissioning
Annex A (normative) - Design data sheet
Annex B (normative) - Qualification data
Annex C (normative) - Short-term pipe spool
        survival test
Annex D (normative) - Measurement of
        [gamma]LCL for through-wall defect
        calculation
Annex E (normative) - Measurement of
        performance test data
Annex F (normative) - Measurement of
        impact performance
Annex G (normative) - Measurement of
        the degradation factor
Annex H (informative) - Axial extent of
        repair look-up table
Annex I (normative) - Installer qualification
Annex J (informative) - Installation requirements
        and guidance
Annex K (informative) - Design considerations
Annex L (informative) - Management of the
        integrity of composite repair systems
        to pipework and vessels
Bibliography

BS EN ISO 24817.

Committee
PSE/17/-/6
DocumentType
Draft
Pages
94
PublisherName
British Standards Institution
Status
Superseded
SupersededBy

ISO 15649:2001 Petroleum and natural gas industries — Piping
AWWA M45 : 3 FIBERGLASS PIPE DESIGN
ISO 527-4:1997 Plastics Determination of tensile properties Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites
ASTM G 8 : 1996 Standard Test Methods for Cathodic Disbonding of Pipeline Coatings
EN 59:2016 Glass reinforced plastics - Determination of indentation hardness by means of a Barcol hardness tester
ANSI/AWWA C200 : 2017 STEEL WATER PIPE, 6 IN. (150 MM) AND LARGER
ASTM D 543 : 2014 : REDLINE Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents
ISO 15310:1999 Fibre-reinforced plastic composites Determination of the in-plane shear modulus by the plate twist method
BS 2782-10 Method 1001:1977 Glass reinforced plastics measurement of hardness by means of a barcol impressor
AWWA C151/A21.51 : 2017 DUCTILE-IRON PIPE, CENTRIFUGALLY CAST
ISO 11359-2:1999 Plastics Thermomechanical analysis (TMA) Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature
AWWA C150/A21.50 : 2014 THICKNESS DESIGN OF DUCTILE-IRON PIPE
AWWA M11 : 2004 STEEL PIPE: A GUIDE FOR DESIGN AND INSTALLATION
ISO 11357-2:2013 Plastics Differential scanning calorimetry (DSC) Part 2: Determination of glass transition temperature and glass transition step height
ASTM C 581 : 2015 : REDLINE Standard Practice for Determining Chemical Resistance of Thermosetting Resins Used in Glass-Fiber-Reinforced Structures Intended for Liquid Service
ASTM D 696 : 2016 : REDLINE Standard Test Method for Coefficient of Linear Thermal Expansion of Plastics Between −30°C and 30°C with a Vitreous Silica Dilatometer
ASTM D 790 : 2017 : REDLINE Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
ISO 10952:2014 Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes and fittings Determination of the resistance to chemical attack for the inside of a section in a deflected condition
API 579-1 : 2016 FITNESS-FOR-SERVICE
ISO 75-3:2004 Plastics — Determination of temperature of deflection under load — Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics
ASTM D 2992 : 2012 Standard Practice for Obtaining Hydrostatic or Pressure Design Basis for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Fittings
ASTM D 638 : 2014 : REDLINE Standard Test Method for Tensile Properties of Plastics
EN 1465:2009 Adhesives - Determination of tensile lap-shear strength of bonded assemblies
ISO 527-1:2012 Plastics Determination of tensile properties Part 1: General principles
ISO 13623:2017 Petroleum and natural gas industries — Pipeline transportation systems
ISO 868:2003 Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness)
ISO 14129:1997 Fibre-reinforced plastic composites — Determination of the in-plane shear stress/shear strain response, including the in-plane shear modulus and strength, by the plus or minus 45 degree tension test method

View more information
$39.22
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more