AAMI ISO 8638 : 2010
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
CARDIOVASCULAR IMPLANTS AND EXTRACORPOREAL SYSTEMS - EXTRACORPOREAL BLOOD CIRCUIT FOR HEMODIALYZERS, HEMODIAFILTERS AND HEMOFILTERS
English
26-07-2010
31-08-2021
Glossary of equivalent standards
Committee representation
Background of ANSI/AAMI adoption of ISO 8638:2010
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements
5 Test methods
6 Labeling
Bibliography
Describes requirements for the single-use extracorporeal blood circuit and (integral and nonintegral) transducer protectors which are intended for use in hemodialysis, hemodiafiltration and hemofiltration.
| Committee |
WG 05
|
| DevelopmentNote |
Supersedes AAMI RD17. (02/2011)
|
| DocumentType |
Standard
|
| Pages |
26
|
| ProductNote |
Reconfirmed 2010
|
| PublisherName |
Association for the Advancement of Medical Instrumentation
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| ISO 8638:2010 | Identical |
| ISO 11137-1:2006 | Sterilization of health care products — Radiation — Part 1: Requirements for development, validation and routine control of a sterilization process for medical devices |
| ISO 10993-4:2017 | Biological evaluation of medical devices — Part 4: Selection of tests for interactions with blood |
| ISO 15223-2:2010 | Medical devices — Symbols to be used with medical device labels, labelling, and information to be supplied — Part 2: Symbol development, selection and validation |
| ISO 8637:2010 | Cardiovascular implants and extracorporeal systems — Haemodialysers, haemodiafilters, haemofilters and haemoconcentrators |
| ISO/TS 17665-2:2009 | Sterilization of health care products — Moist heat — Part 2: Guidance on the application of ISO 17665-1 |
| ISO 14937:2009 | Sterilization of health care products — General requirements for characterization of a sterilizing agent and the development, validation and routine control of a sterilization process for medical devices |
| ISO 11135-1:2007 | Sterilization of health care products — Ethylene oxide — Part 1: Requirements for development, validation and routine control of a sterilization process for medical devices |
| ISO 10993-11:2017 | Biological evaluation of medical devices — Part 11: Tests for systemic toxicity |
| ISO 11137-3:2017 | Sterilization of health care products — Radiation — Part 3: Guidance on dosimetric aspects of development, validation and routine control |
| ISO 10993-7:2008 | Biological evaluation of medical devices — Part 7: Ethylene oxide sterilization residuals |
| ISO 11137-2:2013 | Sterilization of health care products — Radiation — Part 2: Establishing the sterilization dose |
| ISO 7864:2016 | Sterile hypodermic needles for single use — Requirements and test methods |
| ISO 10993-1:2009 | Biological evaluation of medical devices — Part 1: Evaluation and testing within a risk management process |
| ISO/TS 11135-2:2008 | Sterilization of health care products — Ethylene oxide — Part 2: Guidance on the application of ISO 11135-1 |
| ISO 7000:2014 | Graphical symbols for use on equipment — Registered symbols |
| ISO 594-2:1998 | Conical fittings with 6 % (Luer) taper for syringes, needles and certain other medical equipment — Part 2: Lock fittings |
| ISO 15223-1:2016 | Medical devices — Symbols to be used with medical device labels, labelling and information to be supplied — Part 1: General requirements |
| ISO 17665-1:2006 | Sterilization of health care products — Moist heat — Part 1: Requirements for the development, validation and routine control of a sterilization process for medical devices |