Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

AGMA 2001 : D

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

FUNDAMENTAL RATING FACTORS AND CALCULATION METHODS FOR INVOLUTE SPUR AND HELICAL GEAR TEETH

Available format(s)

Hardcopy

Superseded date

10-04-2016

Language(s)

English

Published date

01-01-2004

Foreword
1 Scope
2 Normative references, definitions and symbols
3 Application
4 Criteria for tooth capacity
5 Fundamental rating formulas
6 Geometry factors, I and J
7 Transmitted tangential load, W[t]
8 Dynamic factor, K[v]
9 Overload factor, K[o]
10 Service factor
11 Safety factors, S[H] and S[F]
12 Elastic coefficient, C[p]
13 Surface condition factor, C[f]
14 Hardness ratio factor, C[H]
15 Load distribution factor, K[m]
16 Allowable stress numbers, s[ac] and s[at]
17 Stress cycle factors, Z[N] and Y[N]
18 Reliability factor, K[R]
19 Temperature factor, K[T]
20 Size factor, K[s]
Bibliography
Annexes
A Method for determination of dynamic factor with AGMA 2000-A88
B Rim thickness factor, K[B]
C Application analysis
D Discussion of the analytical face or longitudinal load
  distribution factor
E Gear material fatigue life
F Controlling section size considerations for through hardened
  gearing
Figures
Tables

Describes a comprehensive method for rating the pitting resistance and bending strength of spur and helical involute gear pairs. Includes detailed discussions of factors influencing gear survival and calculation methods.

DevelopmentNote
Supersedes AGMA 218.01 (03/2002) Supplement is available separately, see record AGMA 925. (02/2015) Metric Edition of this standard is available as AGMA 2101. (04/2016)
DocumentType
Standard
Pages
66
PublisherName
American Gear Manufacturers Association
Status
Superseded
SupersededBy
Supersedes

MIL-L-80277 Base Document:1989 LATHES, PRECISION, TOOLROOM, VARIABLE SPEED, 11-INCH THROUGH 13-INCH
03/314804 DC : DRAFT SEP 2003 BS ISO 6336-3 - CALCULATION OF LOAD CAPACITY OF SPUR AND HELICAL GEARS - PART 3: CALCULATION OF TOOTH BENDING STRENGTH
BS ISO 6336-3:2006 Calculation of load capacity of spur and helical gears Calculation of tooth bending strength
MIL-L-23251 Revision E:1989 LATHES, ENGINE AND TOOLROOM 2516 AND 3220
CSA B354.5 : 2007 : R2016 MAST-CLIMBING WORK PLATFORMS
AGMA 6023 : REV A : 1988 : R2000 DESIGN MANUAL FOR ENCLOSED EPICYCLIC GEAR DRIVES
MIL-S-80271 Revision A:1992 SHEARING MACHINE, METAL SQUARING MECHANICAL DRIVE
AGMA 1012 : 2005 GEAR NOMENCLATURE, DEFINITIONS OF TERMS WITH SYMBOLS
B354.12-17 Design, calculations, safety requirements, and test methods for mast climbing transport platforms (MCTPs)
AGMA 6013:2016(R2021) INDUSTRIAL ENCLOSED GEAR DRIVES
A-A-59469 Base Document:1999 Washer-Extractor, Laundry, 35 to 200 Pound Capacity (Naval Shipboard)
ASME BTH 1 : 2017 DESIGN OF BELOW-THE-HOOK LIFTING DEVICES
AGMA 938 : A SHOT PEENING OF GEARS
03/314803 DC : DRAFT SEP 2003 ISO 6336-2 - CALCULATION OF LOAD CAPACITY OF SPUR AND HELICAL GEARS - PART 2: CALCULATION OF SURFACE DURABILITY (PITTING)
API SPEC 11E : 2013 SPECIFICATION FOR PUMPING UNITS
AGMA 912 : A MECHANISMS OF GEAR TOOTH FAILURE
AGMA 6010 : REV F : 1997 : R2003 STANDARD FOR SPUR, HELICAL, HERRINGBONE AND BEVEL ENCLOSED DRIVES
AGMA 6001 : REV D : 1997 DESIGN AND SELECTION OF COMPONENTS FOR ENCLOSED GEAR DRIVES
API 2C RUSSIAN : 2004 SPECIFICATION FOR OFFSHORE PEDESTAL MOUNTED CRANES
ISO/TS 10303-5001:2010 Industrial automation systems and integration — Product data representation and exchange — Part 5001: Guidance on the usage of ISO 10303-214 for gear units
ISO 6336-1:2006 Calculation of load capacity of spur and helical gears Part 1: Basic principles, introduction and general influence factors
B354.9-17 Design, calculations, safety requirements, and test methods for mast climbing work platforms (MCWPs)
API 11E RUSSIAN : 2013 SPECIFICATION FOR PUMPING UNITS
MIL-M-80255 Revision B:1990 MACHINING CENTERS, VERTICAL, SINGLE SPINDLE, COMPUTER NUMERICAL CONTROL (CNC)
AGMA 6023 : A DESIGN MANUAL FOR ENCLOSED EPICYCLIC GEAR DRIVES
AGMA 6023 : REV A : 1988 : R1993 DESIGN MANUAL FOR ENCLOSED EPICYCLIC GEAR DRIVES
AGMA 6010 : REV F : 1997 STANDARD FOR SPUR, HELICAL, HERRINGBONE AND BEVEL ENCLOSED DRIVES
ISO 6336-3:2006 Calculation of load capacity of spur and helical gears Part 3: Calculation of tooth bending strength
API 613:2003 SPECIAL PURPOSE GEAR UNITS FOR PETROLEUM, CHEMICAL AND GAS INDUSTRY SERVICES
API SPEC 11E CHINESE : 2013 SPECIFICATION FOR PUMPING UNITS
ISO 6336-2:2006 Calculation of load capacity of spur and helical gears Part 2: Calculation of surface durability (pitting)
06/30157507 DC : 0 BS ISO 10431 - PETROLEUM AND NATURAL GAS INDUSTRIES - PUMPING UNITS - SPECIFICATION
BS ISO 6336-2:2006 Calculation of load capacity of spur and helical gears Calculation of surface durability (pitting)
AGMA 923 : B METALLURGICAL SPECIFICATIONS OF STEEL GEARING
SAE J 1619 : 2017 SINGLE TOOTH GEAR BENDING FATIGUE TEST
CSA B354.5 : 2007 : INC : UPD 1 : 2008 : R2011 MAST-CLIMBING WORK PLATFORMS
BS ISO 6336-1:2006 Calculation of load capacity of spur and helical gears Basic principles, introduction and general influence factors
CSA B354.5:2007 MAST-CLIMBING WORK PLATFORMS
AGMA 6001 : REV D : 1997 : R2003 DESIGN AND SELECTION OF COMPONENTS FOR ENCLOSED GEAR DRIVES
AGMA 6010 : F STANDARD FOR SPUR, HELICAL, HERRINGBONE AND BEVEL ENCLOSED DRIVES
AGMA 937 : A2012(R2017) AEROSPACE BEVEL GEARS
04/30126837 DC : DRAFT DEC 2004 BS ISO 6336-1 - CALCULATION OF LOAD CAPACITY OF SPUR AND HELICAL GEARS - PART 1: BASIC PRINCIPLES, INTRODUCTION AND GENERAL INFLUENCE FACTORS
MIL-L-80007 Revision E:1989 LATHES, TOOLROOM, 11-INCH THROUGH 13-INCH
AGMA 6001 : D DESIGN AND SELECTION OF COMPONENTS FOR ENCLOSED GEAR DRIVES
API 2C : 2012 OFFSHORE PEDESTAL-MOUNTED CRANES
ASME NUM 1 : 2009 RULES FOR CONSTRUCTION OF CRANES, MONORAILS, AND HOISTS (WITH BRIDGE OR TROLLEY OR HOIST OF THE UNDERHUNG TYPE)

AGMA 933 : B BASIC GEAR GEOMETRY
AGMA 2015-1 : A ACCURACY CLASSIFICATION SYSTEM - TANGENTIAL MEASUREMENTS FOR CYLINDRICAL GEARS
AGMA 6011 : I SPECIFICATION FOR HIGH SPEED HELICAL GEAR UNITS
AGMA 246.02 : A RECOMMENDED PROCEDURE FOR CARBURIZED AEROSPACE GEARING
ISO/TR 10495:1997 Cylindrical gears Calculation of service life under variable loads Conditions for cylindrical gears according to ISO 6336
ASTM A 291 : 2003 Standard Specification for Steel Forgings, Carbon and Alloy, for Pinions, Gears and Shafts for Reduction Gears
AGMA 427.01 : 0 INFORMATION SHEET - SYSTEMS CONSIDERATIONS FOR CRITICAL SERVICE GEAR DRIVES
AGMA 2000 : A GEAR CLASSIFICATION AND INSPECTION HANDBOOK - TOLERANCES AND MEASURING METHODS FOR UNASSEMBLED SPUR AND HELICAL GEARS (INCLUDING METRIC EQUIVALENTS)
AGMA 1010 : E APPEARANCE OF GEAR TEETH - TERMINOLOGY OF WEAR AND FAILURE
AGMA 2007 : C GEARS - SURFACE TEMPER ETCH INSPECTION AFTER GRINDING
AGMA 6000 : B SPECIFICATION FOR MEASUREMENT OF LINEAR VIBRATION ON GEAR UNITS
SAE AMS 2301 : 2015 STEEL CLEANLINESS, AIRCRAFT QUALITY MAGNETIC PARTICLE INSPECTION PROCEDURE
AGMA 925 : A EFFECT OF LUBRICATION ON GEAR SURFACE DISTRESS
AGMA 908 : B GEOMETRY FACTORS FOR DETERMINING THE PITTING RESISTANCE AND BENDING STRENGTH OF SPUR, HELICAL AND HERRINGBONE GEAR TEETH
AGMA 9005 : E INDUSTRIAL GEAR LUBRICATION
ASTM A 535 : 1985 Specification for Special-Quality Ball and Roller Bearing Steel (Withdrawn 1998)
SAE AMS 2300 L : 2015 STEEL CLEANLINESS, PREMIUM AIRCRAFT-QUALITY MAGNETIC PARTICLE INSPECTION PROCEDURE
AGMA 927 : A LOAD DISTRIBUTION FACTORS - ANALYTICAL METHODS FOR CYLINDRICAL GEARS
ASTM E 709 : 2015 : REDLINE Standard Guide for Magnetic Particle Testing
AGMA 6033 : B MATERIALS FOR MARINE PROPULSION GEARING
AGMA 2004 : C GEAR MATERIALS, HEAT TREATMENT AND PROCESSING MANUAL
AGMA 1012 : 2005 GEAR NOMENCLATURE, DEFINITIONS OF TERMS WITH SYMBOLS
ASTM A 534 : 2017 : REDLINE Standard Specification for Carburizing Steels for Anti-Friction Bearings

View more information
$464.61
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more