• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

AS 1646.2-2000

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Elastomeric seals for waterworks purposes Material requirements for pipe joint seals used in water and wastewater applications - Specifies by prescription formulation
Available format(s)

Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users

Superseded date

30-06-2017

Language(s)

English

Published date

01-01-2000

Preview

1 - AS 1646.2-2000 ELASTOMERIC SEALS FOR WATERWORKS PURPOSES - MATERIAL REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND...
4 - PREFACE
5 - CONTENTS
6 - FOREWORD
7 - SECTION 1 SCOPE AND GENERAL
7 - 1.1 SCOPE
7 - 1.2 REFERENCED DOCUMENTS
8 - 1.3 DEFINITIONS
8 - 1.4 MARKING
8 - 1.4.1 Information required
8 - 1.4.2 Identification of elastomer
10 - SECTION 2 MATERIALS AND COMPOSITION
10 - 2.1 GENERAL
10 - 2.2 ELASTOMERS
10 - 2.3 ELASTOMERIC COMPOUNDS
10 - 2.3.1 Protective system
10 - 2.3.2 Filler
10 - 2.3.3 Minimum volume of polymer
10 - 2.4 COPPER AND MANGANESE
11 - SECTION 3 DETERMINATION OF PROPERTIES OF ELASTOMERIC COMPOUNDS
11 - 3.1 GENERAL
11 - 3.2 ELASTOMER HARDNESS
11 - 3.3 TENSILE STRENGTH AND PERCENTAGE ELONGATION AT BREAK
11 - 3.4 COMPRESSION SET
11 - 3.5 LOW TEMPERATURE COMPRESSION SET
11 - 3.6 ACCELERATED AGEING
11 - 3.7 WATER IMMERSION
11 - 3.8 OIL RESISTANCE
11 - 3.9 STRESS RELAXATION IN COMPRESSION
12 - 3.10 OZONE RESISTANCE
13 - SECTION 4 PROPERTIES OF SEALS
13 - 4.1 CONSTRUCTION
13 - 4.2 SEAL HARDNESS
13 - 4.3 PURCHASING
14 - APPENDIX A - MEANS FOR DEMONSTRATING COMPLIANCE WITH THIS STANDARD
14 - A1 SCOPE
14 - A2 RELEVANCE
14 - A3 PRODUCT CERTIFICATION
14 - A4 TESTING
14 - A4.1 General
14 - A4.2 Sampling
15 - A4.3 Retesting
15 - A4.4 Rejection after retest
17 - APPENDIX B - SEAL HARDNESS TEST
17 - B1 SCOPE
17 - B2 METHOD A-MICRO-TESTER METHOD
17 - B3 METHOD B-TYPE ‘A’ DUROMETER METHOD
17 - B3.1 Principle
17 - B3.2 Apparatus
18 - B3.3 Verification of durometer
18 - B3.4 Conditioning
18 - B3.5 Procedure
18 - B4 DETERMINATION OF SEAL HARDNESS
18 - B5 REPORT

Specifies requirements for elastomeric seals to be used in pipeline systems that convey water and wastewater at temperature of less than 50 degrees Celsius. It also specifies composition and formulation requirements for seals.

This Standard specifies requirements for elastomeric seals to be used in pipeline systems that convey water and wastewater at temperatures of less than 50C. It also specifies composition and formulation requirements for seals.Means for demonstrating compliance with this Standard are given in Appendix A.

Committee
WS-010
DocumentType
Standard
ISBN
0 7337 3355 7
Pages
16
PublisherName
Standards Australia
Status
Superseded
SupersededBy
Supersedes
UnderRevision

First published as AS A139-1964.Second edition 1972.Revised and redesignated as AS 1646-1974.Second edition 1984.Third edition 1987.Fourth edition 1992.Revised and redesignated in part as AS 1646.2-2000. First published as AS A139-1964. Second edition 1972. Revised and redesignated as AS 1646-1974. Second edition 1984. Third edition 1987. Fourth edition 1992. Revised and redesignated in part as AS 1646.2-2000.

AS 1683.24-1984 Methods of test for rubber Rubber - Vulcanized - Determination of resistance to ozone cracking - Static strain test
AS 2193-1978 Methods for calibration and grading of force-measuring systems of testing machines
AS 1683.15.2-1990 Methods of test for elastomers Durometer hardness (Reconfirmed 2018)
AS 1199-1988 Sampling procedures and tables for inspection by attributes
AS 1646.3-2000 Elastomeric seals for waterworks purposes - Material requirements for pipe joints seals used in water and wastewater applications with the exception of natural rubber and polyisoprene compounds
AS 1683.11-1990 Methods of test for elastomers Tension testing of vulcanized rubber
HB 18.28-1991 Guidelines for third-party certification and accreditation - Guide 28: General rules for a model third-party certification system for products
AS 1646.1-2000 Elastomeric seals for waterworks purposes - General requirements
AS 2490-1997 Sampling procedures and charts for inspection by variables for percent nonconforming
AS 1683.15.1-1990 Methods of test for elastomers International rubber hardness
AS 1683.13-1992 Methods of test for elastomers - Compression set of vulcanized rubber under constant deflection
AS 1683.23-1983 Methods of test for rubber Rubber - Vulcanized - Determination of resistance to liquids
AS 2490-1981 Sampling procedures and charts for inspection by variables for percent defective

AS 1646.3-2000 Elastomeric seals for waterworks purposes - Material requirements for pipe joints seals used in water and wastewater applications with the exception of natural rubber and polyisoprene compounds
AS 1646.3-2000 Elastomeric seals for waterworks purposes - Material requirements for pipe joints seals used in water and wastewater applications with the exception of natural rubber and polyisoprene compounds
ATS 5200.006-2004 Technical Specification for plumbing and drainage products Reflux valves - sewerage
AS 3517-2007 Capillary fittings of copper and copper alloy for non-pressure sanitary plumbing applications (Reconfirmed 2018)
AS 4087-2004 Metallic flanges for waterworks purposes
AS 5200.000-2006 Technical specification for plumbing and drainage products Procedures for certification of plumbing and drainage products (Reconfirmed 2018)
AS 1357.1-2004 Valves primarily for use in heated water systems - Protection valves
ATS 5200.042-2004 Technical Specification for plumbing and drainage products - Roll-grooved jointing systems
AS/NZS 4798(INT):2005 Polyethylene maintenance shafts
AS/NZS 4058:2007 Precast concrete pipes (pressure and non-pressure)
AS/NZS 4999:2006 PVC-U maintenance shafts
AS/NZS 4999(INT):2003 PVC-U maintenance shafts
AS/NZS 3500.4:2003 Plumbing and drainage Heated water services
AS/NZS 3500.2:2003 Plumbing and drainage Sanitary plumbing and drainage
AS/NZS 4765:2007 Modified PVC (PVC-M) pipes for pressure applications
ATS 5200.476-2006 Technical Specification for plumbing and drainage products Heated water systems - Leak protection device
AS 4809-2003 Copper pipe and fittings - Installation and commissioning
AS/NZS 1477:2006 PVC pipes and fittings for pressure applications
AS 1646.1-2000 Elastomeric seals for waterworks purposes - General requirements
ATS 5200.420-2005 Technical Specification for plumbing and drainage products Trap-priming valves
ATS 5200.477-2006 Technical Specification for plumbing and drainage products Rainwater/mains supply changeover devices
AS/NZS 3518:2004 Acrylonitrile butadiene styrene (ABS) compounds, pipes and fittings for pressure applications
ATS 5200.037.1-2006
AS 4795-2002 Double-flanged butterfly valves for waterworks purposes
AS 2638.2-2006 Gate valves for waterworks purposes - Resilient seated
AS 5200.000-2005 Technical specification for plumbing and drainage products Procedures for certification of plumbing and drainage products
ATS 5200.482-2006 Technical Specification for plumbing and drainage products Soil waste dump fitting
AS/NZS 2280:2004 Ductile iron pipes and fittings
AS/NZS 1254:2002 PVC pipes and fittings for storm and surface water applications
ATS 5200.472-2006 Technical Specification for plumbing and drainage products Heated water system recirculation device
AS 6401-2003 Knife-gate valves for waterworks purposes (Reconfirmed 2015)
AS 2638.1-2002 Gate valves for waterworks purposes Metal seated
AS 4795-2006 Butterfly valves for waterworks purposes
AS/NZS 5065:2005 Polyethylene and polypropylene pipes and fittings for drainage and sewerage applications (Reconfirmed 2017)
ATS 5200.012-2005 Technical Specification for plumbing and drainage products In-line valves for use in plumbing water supply systems - Miscellaneous types metallic and non-metallic
ATS 5200.475-2006 Technical Specification for plumbing and drainage products Heated Water Systems - Cold water recovery device
MP 52-2001 Manual of authorization procedures for plumbing and drainage products
ATS 5200.481-2006 Technical Specification for plumbing and drainage products Thermal switching valves
AS 2638.2-2002 Gate valves for waterworks purposes - Resilient seated
AS 3952-2002 Water supply - Spring hydrant valve for waterworks purposes (Reconfirmed 2015)
AS 4310-2004 DN 80 piston type vacuum interface valves for municipal sewer systems
AS/NZS 3500.1:2003 Plumbing and drainage Water services
AS/NZS 2566.2:2002 Buried flexible pipelines Installation (Reconfirmed 2016)
ATS 5200.030-2004 Technical Specification for plumbing and drainage products - Solenoid valves
AS 3688-2005 Water supply - Metallic fittings and end connectors
AS 1589-2001 Copper and copper alloy waste fittings (Reconfirmed 2018)
ATS 5200.030-2007 Technical Specification for plumbing and drainage products Solenoid valves
AS 4794-2001 Non-return valves for waterworks purposes - Swing check and tilting disc (Reconfirmed 2015)
ATS 5200.485-2006 Pressure compensating tank
AS 1579-2001 Arc-welded steel pipes and fittings for water and wastewater (Reconfirmed 2018)
AS/NZS 1260:2002 PVC-U pipes and fittings for drain, waste and vent application
AS/NZS 2032:2006 Installation of PVC pipe systems

View more information
$99.73
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more