• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

AS/NZS 4291.2:1995

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Mechanical properties of fasteners Nuts with specified proof load values - Coarse thread
Available format(s)

Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users

Superseded date

30-06-2017

Language(s)

English

Published date

05-09-1995

Preview

Specifies materials, mechanical properties and marking requirements for steel nuts of property classes 4, 5, 6, 8, 9, 10 and 12 with ISO metric coarse pitch threads and diameters up to and including 39 mm. The property class system is explained and test methods for determination of mechanical properties are given. Identical with and reproduced from ISO 898-2:1992.

This International Standard specifies the mechanical properties of nuts with specified proof load values when tested at room temperature (see ISO 1). Properties will vary at higher and lower temperature.It applies to nuts- with nominal thread diameters up to and including 39 mm;- of triangular ISO thread and with diameters and pitches according to ISO 68 and ISO 262 (coarse thread);- with diameter/pitch combinations according to ISO 261 (coarse thread);- with thread tolerances 6H according to ISO 965-1 and ISO 965-2;- with specific mechanical requirements;- with widths across flats as specified in ISO 272 or equivalent;- with nominal heights greater than or equal to 0,5D*;- made of carbon steel or low alloy steel.It does not apply to nuts requiring special properties such as- locking abilities (see ISO 2320);- weldability;- corrosion resistance (see ISO 3506);- ability to withstand temperatures above + 300°C or below - 50°C.NOTES1 Nuts made from free-cutting steel should not be used above + 250°C.2 For special products such as nuts for high-strength structural bolting, and overtapped nuts for use with hot dipped galvanized bolts, see the product standards for appropriate values.3 For assemblies with threads having tolerances wider than 6H/6g, there is an increased risk of stripping; see also table 1.4 In the case of thread tolerances other or larger than 6H a decrease of the stripping strength should be considered (see table 1).

Committee
ME-029
DocumentType
Standard
ISBN
0 7262 9813 1
Pages
16
PublisherName
Standards Australia
Status
Superseded
SupersededBy
UnderRevision

Standards Relationship
ISO 898-2:1992 Identical

First published as AS/NZS 4291.2:1995.

AS/NZS 4291.1:1995 Mechanical properties of fasteners Bolts, screws and studs
AS/NZS 1111:1996 ISO metric hexagon commercial bolts and screws
AS/NZS 1112:1996 ISO metric hexagon nuts, including thin nuts, slotted nuts and castle nuts
AS 4291.1-2000 Mechanical properties of fasteners made of carbon steel and alloy steel - Bolts, screws and studs
AS 1815-1991 Metallic materials - Rockwell hardness test
AS 1816-1990 Metallic materials - Brinell hardness test
AS 1817-1991 Metallic materials - Vickers hardness test
AS/NZS 1110:1995 ISO metric precision hexagon bolts and screws
AS 1721-1985 General purpose metric screw threads
AS 1654-1974 Limits and fits for engineering (Metric units)

AS 2294.2-1997 Earth-moving machinery - Protective structures - Laboratory tests and performance requirements for roll-over protective structures
AS 2294.3-1997 Earth-moving machinery - Protective structures - Laboratory tests and performance requirements for falling-object protective structures
AS/NZS 2451:1998 Bolts, screws and nuts with British Standard Whitworth threads (rationalized series)
AS 5047-2005 Hydraulic shoring and trench lining equipment
AS/NZS 4998:2009 Bolted unrestrained mechanical couplings for waterworks purposes (Reconfirmed 2022)
AS/NZS 4793:2009 Mechanical tapping bands for waterworks purposes
AS 4087:2011 Metallic flanges for waterworks purposes
AS/NZS 1252:1996 High-strength steel bolts with associated nuts and washers for structural engineering
AS/NZS 1112:1996 ISO metric hexagon nuts, including thin nuts, slotted nuts and castle nuts
AS/NZS 1559:1997 Hot-dip galvanized steel bolts and associated nuts and washers for tower construction
AS 3533.2-2009 Amusement rides and devices Operation and maintenance
AS 4291.1-2000 Mechanical properties of fasteners made of carbon steel and alloy steel - Bolts, screws and studs

View more information
$79.54
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more