Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 6747 : 2021

Current

Current

The latest, up-to-date edition.

Standard Guide for Selection of Techniques for Electrical Leak Location of Leaks in Geomembranes

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

05-08-2021

1.1This guide is intended to assist individuals or groups in assessing different options available for locating leaks in installed geomembranes using electrical methods. For clarity, this guide uses the term “leak” to mean holes, punctures, tears, knife cuts, seam defects, cracks, and similar breaches in an installed geomembrane (as defined in 3.2.6).

1.2This guide does not cover systems that are restricted to seam testing only, nor does it cover systems that may detect leaks non-electrically. It does not cover systems that only detect the presence, but not the location, of leaks.

1.3(Warning—The electrical methods used for geomembrane leak location could use high voltages, resulting in the potential for electrical shock or electrocution. This hazard might be increased because operations might be conducted in or near water. In particular, a high voltage could exist between the water or earth material and earth ground, or any grounded conductor. These procedures are potentially very dangerous, and can result in personal injury or death. The electrical methods used for geomembrane leak location should be attempted only by qualified and experienced personnel. Appropriate safety measures must be taken to protect the leak location operators as well as other people at the site.)

1.4The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
D 35
DocumentType
Guide
Pages
14
PublisherName
American Society for Testing and Materials
Status
Current
Supersedes

ASTM D 7852 : 2013 Standard Practice for Use of an Electrically Conductive Geotextile for Leak Location Surveys
ASTM D 7953 : 2020 Standard Practice for Electrical Leak Location on Exposed Geomembranes Using the Arc Testing Method
ASTM D 7240 : 2018 Standard Practice for Electrical Leak Location Using Geomembranes with an Insulating Layer in Intimate Contact with a Conductive Layer via Electrical Capacitance Technique (Conductive-Backed Geomembrane Spark Test)
ASTM D 7877 : 2014 Standard Guide for Electronic Methods for Detecting and Locating Leaks in Waterproof Membranes
ASTM D 7700 : 2015 Standard Guide for Selecting Test Methods for Geomembrane Seams
ASTM D 7931/D7931M : 2021 Standard Guide for Specifying Drainage Geocomposites
ASTM D 7007 : 2016 Standard Practices for Electrical Methods for Locating Leaks in Geomembranes Covered with Water or Earthen Materials
ASTM D 6455 : 2011 : R2018 Standard Guide for the Selection of Test Methods for Prefabricated Bituminous Geomembranes (PBGMs)
ASTM D 7909 : 2021 : REV A Standard Guide for Placement of Intentional Leaks During Electrical Leak Location Surveys of Geomembranes
ASTM D 7931/D7931M : 2021 : REV A Standard Guide for Specifying Drainage Geocomposites

ASTM D 4439 : 2020 Standard Terminology for Geosynthetics
ASTM D 7852 : 2023 Standard Practice for Use of an Electrically Conductive Geotextile for Leak Location Surveys
ASTM D 7852 : 2013 : R2022 Standard Practice for Use of an Electrically Conductive Geotextile for Leak Location Surveys
ASTM D 7703 : 2022 Standard Practice for Electrical Leak Location on Exposed Geomembranes Using the Water Lance Method
ASTM D 7002 : 2022 Standard Practice for Electrical Leak Location on Exposed Geomembranes Using the Water Puddle Method
ASTM D 7852 : 2013 Standard Practice for Use of an Electrically Conductive Geotextile for Leak Location Surveys
ASTM D 7002 : 2016 Standard Practice for Electrical Leak Location on Exposed Geomembranes Using the Water Puddle Method
ASTM D 7703 : 2016 Standard Practice for Electrical Leak Location on Exposed Geomembranes Using the Water Lance Method
ASTM D 4439 : 2024 Standard Terminology for Geosynthetics
ASTM D 4439 : 2023 : REV A Standard Terminology for Geosynthetics
ASTM D 4439 : 2023 : REV B Standard Terminology for Geosynthetics
ASTM D 7007 : 2024 Standard Practices for Electrical Methods for Locating Leaks in Geomembranes Covered with Water or Earthen Materials
ASTM D 8265 : 2023 Standard Practices for Electrical Methods for Mapping Leaks in Installed Geomembranes
ASTM D 8265 : 2021 Standard Practices for Electrical Methods for Mapping Leaks in Installed Geomembranes
ASTM D 4439 : 2023 Standard Terminology for Geosynthetics

View more information
$115.52
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more