Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM F 2807 : 2013 : R2018

Current

Current

The latest, up-to-date edition.

Standard Specification for Multilayer Polyethylene-Polyamide (PE-PA) Pipe for Pressure Piping Applications (Withdrawn 2024)

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

01-01-2018

CONTAINED IN VOL. 08.04, 2018 Defines requirements and test methods for 1/2 in. through 14 in. multilayer polyethylene-polyamide (PE-PA) pipe, which is a two-layer pipe (PE pipe layer bonded to an inner layer of PA).

Committee
F 17
DocumentType
Standard
Pages
7
ProductNote
Reconfirmed 2018
PublisherName
American Society for Testing and Materials
Status
Current
Supersedes

1.1This specification covers requirements and test methods for 1/2in. through 14 in. multilayer polyethylene-polyamide (PE-PA) pipe, which is a two-layer pipe (PE pipe layer bonded to an inner layer of PA). The multilayer pipe covered by this specification is intended for use in piping applications where the permeation and chemical resistance of polyamide (PA) compounds may be useful to protect the PE pipe layer, such as oil and gas producing applications that convey oil, dry or wet gas, and multiphase fluids.

Note 1:Permeability and chemical resistance depends on the type of PA used. The PA layer delays but does not prevent liquid hydrocarbons effects. Therefore, the hydrocarbon chemical design factor for this multilayer pipe should be the same as for PE pipe layer—see X1.2.

1.2Electrofusion and mechanical joints are typically used for this multilayer pipe.

1.3Unless specified otherwise, all the pipe requirements in this specification are for the multilayer pipe.

1.4The PA layer is not taken into consideration for the design pressure of multilayer pipe meeting this specification. Design pressure rating is determined from the PE pipe layer alone—see Appendix X1.

1.5Units—The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.6The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in figures and tables) shall not be considered as requirements of the standard.

1.7The following precautionary caveat pertains only to the test method portion, Section 6, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.8This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM D 2837 : 2013 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
ASTM D 1600 : 1999 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM D 6779 : 2002 Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 6779 : 2005 Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 6779 : 2020 Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
ASTM D 6779 : 2007 : REV A Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 2290 : 2016 Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe
ASTM D 1598 : 2002 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
ASTM D 2122 : 1998 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
ASTM D 2290 : 2019 : REV A Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe
MIL-STD-129 Revision R:2014 Military Marking for Shipment and Storage
ASTM D 618 : 2013 : REDLINE Standard Practice for Conditioning Plastics for Testing
ASTM D 1598 : 2015 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
ASTM F 412 : 2020 : REV A Standard Terminology Relating to Plastic Piping Systems
ASTM D 4218 : 2020 Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds by the Muffle-Furnace Technique
ASTM D 1598 : 2015 : REV A Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
ASTM F 412 : 2021 Standard Terminology Relating to Plastic Piping Systems
ASTM D 2837 : 2001 : REV A Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials
ASTM D 6779 : 2003 Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 1603 : 2001 Standard Test Method for Carbon Black In Olefin Plastics
ASTM D 3350 : 2000 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D 6779 : 2011 Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 1598 : 2023 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
ASTM D 3350 : 2008 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D 6779 : 2008 Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 4218 : 1996 : R2001 Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds By the Muffle-Furnace Technique
ASTM D 2837 : 2002 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials
ASTM D 2837 : 2001 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials
ASTM F 1290 : 1998 : REV A : R2004 Standard Practice for Electrofusion Joining Polyolefin Pipe and Fittings
ASTM D 3350 : 2021 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D 2837 : 2004 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
ASTM D 2837 : 2021 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
ASTM D 6779 : 2017 : REDLINE Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
ASTM D 3350 : 2002 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D 6779 : 2004 Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 1600 : 2007 Standard Terminology for Abbreviated Terms Relating to Plastics
PPI TR 3 : 2017 POLICIES AND PROCEDURES FOR DEVELOPING HYDROSTATIC DESIGN BASIS (HDB), HYDROSTATIC DESIGN STRESSES (HDS), PRESSURE DESIGN BASIS (PDB), STRENGTH DESIGN BASIS (SDB), MINIMUM REQUIRED STRENGTH (MRS) RATINGS, AND CATEGORIZED REQUIRED STRENGTH (CRS) FOR THERMOPLASTIC PIPING MATERIALS OR PIPE
ASTM D 1600 : 2013 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM D 3350 : 2014 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D 4218 : 1996 : R2008 Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds By the Muffle-Furnace Technique
ASTM D 6779 : 2012 Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
ASTM D 2290 : 2004 Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe by Split Disk Method
ASTM D 1600 : 2014 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM D 2837 : 2008 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
ASTM D 6779 : 2006 Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 2837 : 1998 : REV A Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials
PPI TR 4 : 2017 HDB/HDS/SDB/PDB/MRS LISTED MATERIALS - PPI LISTING OF HYDROSTATIC DESIGN BASIS (HDB), HYDROSTATIC DESIGN STRESS (HDS), STRENGTH DESIGN BASIS (SDB), PRESSURE DESIGN BASIS (PDB) AND MINIMUM REQUIRED STRENGTH (MRS) RATINGS FOR THERMOPLASTIC PIPING MATERIALS OR PIPE
ASTM D 1600 : 2008 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM D 1598 : 1997 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
EN 14125:2013 Thermoplastic and flexible metal pipework for underground installation at petrol filling stations
ASTM D 2837 : 2001 : REV A : EDT 1 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials
ASTM D 3350 : 2004 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D 1603 : 2020 Standard Test Method for Carbon Black Content in Olefin Plastics
ASTM D 2837 : 2011 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
ASTM D 3350 : 2002 : REV A Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D 1599 : 2014 Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
ASTM D 1599 : 2014 : EDT 1 Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
ASTM D 3350 : 2012 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D 3350 : 2001 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D 1603 : 2011 Standard Test Method for Carbon Black Content in Olefin Plastics
ISO 3126:2005 Plastics piping systems Plastics components Determination of dimensions
ASTM D 1603 : 2014 : REDLINE Standard Test Method for Carbon Black Content in Olefin Plastics
ASTM D 3350 : 2012 : EDT 1 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D 2122 : 1998 : EDT 1 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
FED-STD-123 Revision H:2007 MARKING FOR SHIPMENT (CIVIL AGENCIES)
ASTM D 1603 : 1994 Standard Test Method for Carbon Black In Olefin Plastics
ASTM D 1599 : 2018 Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
ASTM D 2837 : 2022 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
ASTM D 1599 : 1999 : R2011 Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
ASTM D 2290 : 2000 Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe by Split Disk Method
ASTM D 1603 : 2006 Standard Test Method for Carbon Black Content in Olefin Plastics
ASTM D 1599 : 1999 : EDT 1 Standard Test Method for Resistance to Short-Time Hydraulic Failure Pressure of Plastic Pipe, Tubing, and Fittings
ASTM D 6779 : 2004 : REV A Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM F 2619/F2619M : 2013 : REDLINE Standard Specification for High-Density Polyethylene (PE) Line Pipe
ASTM D 6779 : 2023 Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
ASTM D 4218 : 2015 Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds By the Muffle-Furnace Technique
ISO 8510-2:2006 Adhesives Peel test for a flexible-bonded-to-rigid test specimen assembly Part 2: 180 peel
ASTM D 2122 : 2022 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
ASTM D 1600 : 2018 Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
ASTM D 6779 : 2012 : REV A Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
ASTM D 3350 : 2010 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM F 1290 : 1998 : REV A : R2011 Standard Practice for Electrofusion Joining Polyolefin Pipe and Fittings
ASTM D 618 : 2013 Standard Practice for Conditioning Plastics for Testing
ASTM F 412 : 2023 Standard Terminology Relating to Plastic Piping Systems
ASTM D 1598 : 2021 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
ASTM D 2122 : 2016 : REDLINE Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
ASTM D 1598 : 2002 : R2008 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
ASTM D 6779 : 2002 : REV A Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 3350 : 2006 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D 2290 : 2016-12 TEST METHOD FOR APPARENT HOOP TENSILE STRENGTH OF PLASTIC OR REINFORCED PLASTIC PIPE
ASTM D 2290 : 2000 : EDT 1 Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe by Split Disk Method
ASTM D 2122 : 1998 : R2004 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
ASTM D 3350 : 2010 : REV A Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D 2122 : 2016 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
ASTM F 1290 : 1998 : REV A Standard Practice for Electrofusion Joining Polyolefin Pipe and Fittings
ASTM D 2290 : 2019 Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe
ASTM D 3350 : 2014 : REDLINE Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D 1603 : 2014 Standard Test Method for Carbon Black Content in Olefin Plastics
ASTM D 1603 : 2012 Standard Test Method for Carbon Black Content in Olefin Plastics
ASTM D 1599 : 1999 : R2005 Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
ASTM D 1598 : 2002 : R2009 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
ASTM D 2290 : 2012 Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe
ASTM D 6779 : 2016 Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
ASTM D 6779 : 2007 Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 6779 : 2021 Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
ASTM D 6779 : 2010 Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 2122 : 1998 : R2010 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
SAE J 2260 : 2004 NONMETALLIC FUEL SYSTEM TUBING WITH ONE OR MORE LAYERS
ASTM D 2290 : 2008 Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe by Split Disk Method
ASTM D 1599 : 1999 Standard Test Method for Resistance to Short-Time Hydraulic Failure Pressure of Plastic Pipe, Tubing, and Fittings
ASTM D 618 : 2021 Standard Practice for Conditioning Plastics for Testing
ASTM D 3350 : 2005 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D 2122 : 2015 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
ASTM D 6779 : 2017 Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
ASTM D 4218 : 1996 Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds By the Muffle-Furnace Technique
ASTM D 6779 : 2008 : REV A Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 6779 : 2006 : EDT 1 Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 2837 : 2013 : EDT 1 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
ASTM D 2837 : 2004 : EDT 1 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products

View more information
$125.58
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more