Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM F 3111 : 2016 : REDLINE

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Specification for Heavy Hex Structural Bolt/Nut/Washer Assemblies, Alloy Steel, Heat Treated, 200 ksi Minimum Tensile Strength

Available format(s)

PDF

Superseded date

18-05-2024

Language(s)

English

Published date

18-05-2016

CONTAINED IN VOL. 01.09, 2018 Defines heat treated, alloy steel, heavy hex structural bolt/nut/washer assemblies, also referred to as 'sets,' having a tensile strength of 200 to 215 ksi.

1.1This specification covers heat treated, alloy steel, heavy hex structural bolt/nut/washer assemblies, also referred to as “sets,” having a tensile strength of 200 to 215 ksi. These assemblies are capable of developing a minimum predetermined tension when installed by applying an initial torque followed by rotation to the nut or bolt head, while at the same time preventing the rotation of the opposite side of the assembly.

Note 1:The installations in Appendix X1 are important to the proper application of this product.

1.2An assembly consists of a heavy hex structural head bolt, nut and two washers covered by this specification.

1.3The assemblies are available in sizes 1 in. to 1 1/4in. inclusive.

1.4The fastener assemblies are intended for use in structural connections in the following environmental conditions:

1.4.1Interiors, normally dry, including interiors where structural steel is embedded in concrete, encased in masonry or protected by membrane or noncorrosive contact type fireproofing.

1.4.2Interiors and exteriors, normally dry, under roof, where the installed assemblies are soundly protected by a shop-applied or field-applied coating to the structural steel system.

1.5The fastener assemblies are not intended for use in structural connections in the following environments, with or without protection by a shop-applied or field-applied coating to the structural steel system:

1.5.1Exteriors not under roof.

1.5.2Chemical environments in which strong concentrations of highly corrosive gases, fumes, or chemicals, either in solution or as concentrated liquids or solids, contact the fasteners or their protective coating.

1.5.3Heavy industrial environments severe enough to be classified as a chemical environment as described in 1.5.2.

1.5.4Condensation and high humidity environments maintaining almost continuous condensation, including submerged in water and soil.

1.5.5Cathodically protected environments, in which current is applied to the structural steel system by the sacrificial anode method or the DC power method.

1.6Units—The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.

1.7The following precautionary statement pertains only to the test method portions, Section 13, Section 14 and Annex A2 of this Specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
F 16
DocumentType
Redline
Pages
15
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy

ASTM F 606/F606M : 2016 : REDLINE Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets
ASTM F 788 : 2013-04 SPECIFICATION FOR SURFACE DISCONTINUITIES OF BOLTS, SCREWS, AND STUDS, INCH AND METRIC SERIES
ASME B1.15 : 1995 UNIFIED INCH SCREW THREADS (UNJ THREAD FORM)
ASTM F 2328 : 2017 : REDLINE Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws, Studs, and Nuts
ASTM E 709 : 2015 : REDLINE Standard Guide for Magnetic Particle Testing

View more information
$138.96
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more