BIS IS 513 : 2008 AMD 2 2016
Current
Current
The latest, up-to-date edition.
COLD REDUCED LOW CARBON STEEL SHEET AND STRIP
Published date
12-01-2013
Publisher
Sorry this product is not available in your region.
FOREWORD
1 SCOPE
2 REFERENCES
3 CLASSIFICATION OF GRADES
4 SUPPLY OF MATERIAL
5 MANUFACTURE
6 CHEMICAL COMPOSITION
7 MECHANICAL AND PHYSICAL PROPERTIES
8 SURFACE FINISH
9 FREEDOM FROM DEFECTS
10 DIMENSIONS AND TOLERANCES
11 SAMPLING FOR TESTS
12 MARKING
ANNEX A (Foreword) - CORRELATION OF OLD
AND NEW GRADES/DESIGNATIONS
ANNEX B (Clause 4.4.3 and 4.4.3.1) - STABILITY
TEST
ANNEX C (Foreword) - COMMITTEE COMPOSITION
Specifies the requirements of cold reduced low carbon steel sheets and strips for bending and drawing purpose and where the surface is of prime importance.
| Committee |
MTD 4
|
| DevelopmentNote |
Supersedes BIS IS 4030. (09/2008)
|
| DocumentType |
Standard
|
| PublisherName |
Bureau of Indian Standards
|
| Status |
Current
|
| Supersedes |
| BIS IS 10864 : 2013 | METAL JACKETED GASKETS FOR PIPE FLANGES AND HEAT EXCHANGER FLANGES - SPECIFICATION |
| BIS IS 1956-4 : 2013 | GLOSSARY OF TERMS RELATING TO IRON AND STEEL - PART 4: FLAT PRODUCTS |
| BIS IS 16176 : 2014 | RATCHET PIPE THREADER FOR TAPER PIPE THREADS (R-SERIES) - SPECIFICATION |
| BIS IS 1783-2 : 2014 | DRUMS LARGE, FIXED ENDS - SPECIFICATION - PART 2: GRADE B DRUMS |
| BIS IS 950 : 2012 | FUNCTIONAL REQUIREMENTS FOR WATER TENDER, TYPE B FOR FIRE BRIGADE USE |
| BIS IS 5244 : 2014 AMD 1 2015 | SAFE DEPOSIT LOCKER CABINETS - SPECIFICATION |
| BIS IS 14246 : 2013 | CONTINUOUSLY PRE-PAINTED GALVANIZED STEEL SHEETS AND COILS |
| BIS IS 15908 : 2011 | SELECTION, INSTALLATION AND MAINTENANCE OF CONTROL AND INDICATING EQUIPMENTS FOR FIRE DETECTION AND ALARM SYSTEM - CODE OF PRACTICE |
| BIS IS 2932-1 : 2013 AMD 1 2015 | ENAMEL, SYNTHETIC, EXTERIOR: (A) UNDERCOATING (B) FINISHING - SPECIFICATION |
| IS 13997 : 2014 | DRUMS, LARGE OPEN TOP - SPECIFICATION |
| BIS IS 1239-1 : 2004 AMD 5 2017 | STEEL TUBES, TUBULARS AND OTHER WROUGHT STEEL FITTINGS - SPECIFICATION - PART 1: STEEL TUBES |
| BIS IS 12933-2 : 2003 AMD 3 2013 | SOLAR FLAT PLATE COLLECTOR - SPECIFICATION - PART 2: COMPONENTS |
| BIS IS 800 : 2007 AMD 1 2012 | GENERAL CONSTRUCTION IN STEEL - CODE OF PRACTICE |
| BIS IS 629 : 2013 | BICYCLE - HUB ASSEMBLY - SPECIFICATION |
| BIS IS 7142 : 1995(R2006) | WELDED LOW CARBON STEEL CYLINDERS FOR LOW PRESSURE LIQUEFIABLE GASES NOT EXCEEDING 5 LITRE WATER CAPACITY - SPECIFICATION |
| BIS IS 16074 : 2013 | STEEL FLUSH DOOR SHUTTERS - SPECIFICATION |
| BIS IS 13152-1 : 2013 | PORTABLE SOLID BIO-MASS COOKSTOVE (CHULHA) - SPECIFICATION |
| ISO 6932:2014 | Cold-reduced carbon steel strip with a maximum carbon content of 0,25 % |
| BIS IS 3074 : 2013 | STEEL TUBES FOR AUTOMOTIVE PURPOSES - SPECIFICATION |
| 13/30280533 DC : 0 | BS ISO 6932 - COLD-REDUCED CARBON STEEL STRIP WITH A MAXIMUM CARBON CONTENT OF 0,25% |
| BS ISO 6932:2014 | Cold-reduced carbon steel strip with a maximum carbon content of 0,25 % |
| BIS IS 15961 : 2012 AMD 1 2016 | HOT DIP ALUMINIUM-ZINC ALLOY METALLIC COATED STEEL STRIP AND SHEET (PLAIN) |
| BIS IS 11188-1 : 2014 AMD 1 2015 | VAULT (STRONG ROOM) DOORS - PART 1: SPECIFICATION |
| ISO 6507-1:2005 | Metallic materials — Vickers hardness test — Part 1: Test method |
| ISO 10275:2007 | Metallic materials — Sheet and strip — Determination of tensile strain hardening exponent |
| BIS IS 1586 : 2000(R2006) | METHOD FOR ROCKWELL HARDNESS TEST FOR METALLIC MATERIAL (SCALES A-B-C-D-E-F-G-H-K 15N, 30N, 45N, 15T, 30T AND 45T) |
| ISO 6892:1998 | Metallic materials — Tensile testing at ambient temperature |
| BIS IS 10175-1 : 1993(R2003) | MECHANICAL TESTING OF METALS - MODIFIED ERICHSEN CUPPING TEST - SHEET AND STRIP PT 1 THICKNESS UPTO 2 MM |
| BIS IS 1501 : 2002 | METHOD FOR VICKERS HARDNESS TEST FOR METALLIC MATERIALS |
| BIS IS 11999 : 2007(R2009) | METHOD FOR DETERMINATION OF PLASTIC STRAIN RATIO 'R' FOR STEEL SHEETS |
| BIS IS 1599 : 2012(R2017) | METALLIC MATERIALS - BEND TEST |
| BIS IS 15756 : 2007 | METALLIC MATERIALS - SHEET AND STRIP - DETERMINATION OF TENSILE STRAIN HARDENING EXPONENT |
| BIS IS 1608 : 2005 | METALLIC MATERIALS - TENSILE TESTING AT AMBIENT TEMPERATURE |
| BIS IS/ISO 16162 : 2012 | CONTINUOUSLY COLD-ROLLED STEEL SHEET PRODUCTS - DIMENSIONAL AND SHAPE TOLERANCES |
| BIS IS 8910 : 2010 | GENERAL TECHNICAL DELIVERY REQUIREMENTS FOR STEEL AND STEEL PRODUCTS |
Summarise
Sorry this product is not available in your region.