BS 5412&5413-5(1976) : AMD 4591
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
SPECIFICATION FOR THE PERFORMANCE OF DRAW-OFF TAPS WITH METAL BODIES FOR WATER SERVICES - PHYSIO-CHEMICAL CHARACTERISTICS MATERIALS COATINGS
23-11-2012
15-01-1996
Foreword
Cooperating organizations
Specification
Section one. General
1 Scope
2 References
3 Definitions
4 Requirements for compliance with BS 5412 and BS 5413
5 Nominal size
6 Marking
7 Identification of taps
Section two. Physio-chemical characteristics:
materials, coatings
8 General
9 Materials
10 Application of materials
11 Coatings
12 Workmanship
Appendices
A Low temperature test for 'O'-rings and other
elastomeric type seals
B Properties of materials and test requirements for
'O'-rings and other elastomeric type seals
C Adhesion to and corrosion of metals and plastics
material by 'O'-rings and other elastomeric type
seals. Test methods
D Properties of lubricating oils for materials tests
for 'O'-rings and other elastomeric type seals
E Method for the determination of surface conditions
of 'O'-ring and other elastomeric type seal
materials on bending after ageing in air
F Method for the determination of tensile elongation
at break of plastic materials
Figures
1 Adhesion and corrosion test apparatus
2 Test specimen
Defines the physio-chemical characteristics and tests for half and three-quarter nominal size draw-off taps. Relates to following types of tap: pillar and bib taps, combination tap assemblies, single hole combination tap assemblies, and three hole combination tap assemblies.
| Committee |
SEB/2
|
| DevelopmentNote |
ALSO NUMBERED AS BS 5413 PART 5 1976
|
| DocumentType |
Standard
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| BS 1206:1974 | Specification for fireclay sinks: dimensions and workmanship |
| BS 6282-4:1982 | Devices with moving parts for the prevention of contamination of water by backflow Specification for combined check and anti-vacuum valves of nominal size up to and including DN 42 |
| BS 6340-4:1984 | Shower units Specification for shower heads and related equipment |
| BS 6281-3:1982 | Devices without moving parts for the prevention of contamination of water by backflow Specification for pipe interrupters of nominal size up to and including DN 42 |
| BS 6282-1:1982 | Devices with moving parts for the prevention of contamination of water by backflow Specification for check valves of nominal size up to and including DN 54 |
| BS 2879:1980 | Specification for draining taps (screw-down pattern) |
| BS 6282-3:1982 | Devices with moving parts for the prevention of contamination of water by backflow Specification for in-line anti-vacuum valves of nominal size up to and including DN 42 |
| BS 6340-2:1983 | Shower units Specification for the installation of shower units |
| BS 5779:1979 | Specification for spray mixing taps |
| BS 6282-2:1982 | Devices with moving parts for the prevention of contamination of water by backflow Specification for terminal anti-vacuum valves of nominal size up to and including DN 54 |
| BS 2871-1:1971 | Specification for copper and copper alloys. Tubes Copper tubes for water, gas and sanitation |
| BS 970-4:1970 | Specification for wrought steels for mechanical and allied engineering purposes Valve steels |
| BS 903-A26:1969 | Physical testing of rubber Determination of hardness |
| BS 1010-2:1973 | Specification for draw-off taps and stopvalves for water services (screw-down pattern) Draw-off taps and above-ground stopvalves |