BS EN 10002-5:1992
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Tensile testing of metallic materials Method of test at elevated temperatures
Hardcopy , PDF
English
01-04-1992
28-02-2011
Cooperating organizations
National foreword
Foreword
1 Scope
2 Normative references
3 Principle
4 Definitions
5 Symbols and Designations
6 Test Pieces
7 Determination of original cross-sectional area (S[O])
8 Marking the original gauge length (L[O])
9 Testing apparatus
10 Conditions of testing
11 Determination of percentage elongation after fracture (A)
12 Determination of proof Strength (non-proportional extension)
(R[p])
13 Determination of proof strength (total extension) (R[t])
14 Method of verification of permanent set strength (R[r])
15 Test report
Annex A (Normative annex) - Types of test piece to be used
for thin products: sheets, strips and flats between
0.1 mm AND 3 mm
Annex B (Normative annex) - types of test pieces to be used
in the case of wire, bars and sections with a diameter
or thickness of less than 4 mm
Annex C (Normative annex) - Types of test pieces to be used
in the case of sheets and flats of thickness equal
to or greater than 3 mm, and wire, bars and sections
of diameter or thickness equal to or greater than 4 mm
Annex D (Normative annex) - Types of test pieces to be used
in the case of tubes
Annex E (Normative annex) - Measurement or percentage elongation
after fracture, based on sub-division of the original
gauge length
Annex F (Informative annex) - List of national standards
corresponding to reference Euronorm 18
Annex G (Informative annex) - Bibliography
National annex NA (informative)
National annex NB (informative)
Defines the mechanical properties which can be determined at elevated temperature.
| Committee |
ISE/101
|
| DevelopmentNote |
Supersedes BS 3688-1(1963) and 88/37338 DC (11/2003) Reviewed and confirmed by BSI, September 2007. (09/2007)
|
| DocumentType |
Standard
|
| Pages |
32
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| I.S. EN 10002-5:1992 | Identical |
| NBN EN 10002-5 : 1992 | Identical |
| NEN EN 10002-5 : 1992 | Identical |
| DIN EN 10002-5:1992-02 | Identical |
| NS EN 10002-5 : 1ED 1992 | Identical |
| NF EN 10002-5 : 1992 | Identical |
| EN 10002-5:1991 | Identical |
| 04/30102371 DC : 0 | BS 5A 4-6 - AEROSPACE SERIES - TEST PIECES AND TEST METHODS FOR METALLIC MATERIALS - PART 6: TENSILE TESTING ELEVATED TEMPERATURE |
| PD 5500:2000 | SPECIFICATION FOR UNFIRED FUSION WELDED PRESSURE VESSELS |
| BS 4825-1(1991) : 1991 | STAINLESS STEEL TUBES AND FITTINGS FOR THE FOOD INDUSTRY AND OTHER HYGIENIC APPLICATIONS - PART 1: SPECIFICATION FOR TUBES |
| DEFSTAN 02-848(PT2)/3(2010) : 2010 | REQUIREMENTS FOR CARBON-MANGANESE AND LOW ALLOY STEEL FORGINGS - PART 2: LOW ALLOY STEEL FORGINGS |
| DEFSTAN 02-848(PT1)/3(2010) : 2010 | REQUIREMENTS FOR CARBON-MANGANESE AND LOW ALLOY STEEL FORGINGS - PART 1: CARBON-MANGANESE STEEL FORGINGS |
| DEFSTAN 02-848(PT1)/2(2004) : 2004 | REQUIREMENTS FOR CARBON-MANGANESE AND LOW ALLOY STEEL FORGINGS - PART 1: CARBON-MANGANESE STEEL FORGINGS |
| DEFSTAN 02-848(PT2)/2(2004) : 2004 | REQUIREMENTS FOR CARBON-MANGANESE AND LOW ALLOY STEEL FORGINGS - PART 2: LOW ALLOY STEEL FORGINGS |
| 02/710149 DC : 0 | PD 2790 - SPECIFICATION FOR THE DESIGN AND MANUFACTURE OF SHELL BOILERS |
| BS PD5500(2015) : 2015 | SPECIFICATION FOR UNFIRED FUSION WELDED PRESSURE VESSELS |
| BS 2790:1992 | Specification for design and manufacture of shell boilers of welded construction |
| BS 7910:2005 | Guide to methods for assessing the acceptability of flaws in metallic structures |
| BS PD5500(2009) : 2009 | SPECIFICATION FOR UNFIRED FUSION WELDED PRESSURE VESSELS |
| PD 5500:2003 | Specification for unfired fusion welded pressure vessels |
| BS PD5500(2006) : 2006 | SPECIFICATION FOR UNFIRED FUSION WELDED PRESSURE VESSELS |
| BS PD5500(2018) : 2018 | SPECIFICATION FOR UNFIRED FUSION WELDED PRESSURE VESSELS |
| BS 806:1993 | Specification for design and construction of ferrous piping installations for and in connection with land boilers |
| BS PD5500(2012) : 2012 | SPECIFICATION FOR UNFIRED FUSION WELDED PRESSURE VESSELS |
| BS 3843-3:1992 | Guide to terotechnology (the economic management of assets) Guide to the available techniques |
| BS 8118-1:1991 | Structural use of aluminium Code of practice for design |
| 04/30111613 DC : DRAFT OCT 2004 | BS 7910 - GUIDE TO METHODS FOR ASSESSING THE ACCEPTABILITY OF FLAWS IN FUSION WELDED STRUCTURES |
| EURONORM 18 : 1979 | TAKING AND PREPARATION OF SAMPLES AND SAMPLE SECTIONS OF STEEL AND STEEL PRODUCTS |
| ISO 2566-2:1984 | Steel — Conversion of elongation values — Part 2: Austenitic steels |
| BS EN 10002-4:1995 | Tensile testing of metallic materials Verification of extensometers used in uniaxial testing |
| ISO 2566-1:1984 | Steel — Conversion of elongation values — Part 1: Carbon and low alloy steels |
| BS EN 10002-2:1992 | Tensile testing of metallic materials Verification of the force measuring system of the tensile testing machine |
| BS EN 10002-1:2001 | Tensile testing of metallic materials Method of test at ambient temperature |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : All end users must be registered with an Account prior to user licenses being assigned.