BS EN 50411-2-5:2009

1 Scope
   1.1 Product definition
   1.2 Operating environment
   1.3 Reliability
   1.4 Quality assurance
   1.5 Allowed fibre and cable types
   1.6 Allowed microduct connector types
   1.7 Microduct storage constraints
2 Normative references
3 Definitions and abbreviations
   3.1 Definitions
   3.2 Abbreviations
4 Description
   4.1 Microduct closure
   4.2 Closure housing functions
   4.3 Burst pressure
   4.4 Closure housing configurations
   4.5 Entry seals
   4.6 Common base configurations
   4.7 Microduct management system
   4.8 Materials
   4.9 Colour and marking
   4.10 Microduct connectors applications and capacity
5 Variants
6 Dimensional requirements
   6.1 Dimensions of inline closures
   6.2 Dimensions of tee closures
   6.3 Dimensions of pan closures
   6.4 Dimensions of dome closures
7 Tests
   7.1 Sample size
   7.2 Test sample preparation
   7.3 Test and measurement methods
   7.4 Test sequence
   7.5 Pass/fail criteria
8 Test report
9 Performance requirements
   9.1 Dimensional and marking requirements
   9.2 Sealing, optical and appearance performance criteria
   9.3 Mechanical sealing performance requirements
   9.4 Environmental sealing performance requirements
   9.5 Mechanical optical performance requirements
   9.6 Environmental optical performance requirements
Annex A (informative) - Fibre for test sample details
Annex B (informative) - Sample size and product sourcing
        requirements
Annex C (informative) - Closure minimum internal diameters,
        containing microduct connectors
Annex D (informative) - Typical buried blown fibre microduct
        cable outside diameters
Annex E (informative) - Microduct connector definitions and
        sketches
Annex F (informative) - Microduct minimum bend radius
Bibliography

Covers the initial, start of life dimensional, optical, mechanical and environmental performance requirements which a fully installed blown fibre protected microduct closure must meet in order for it to be categorised as an EN standard product.

1.1 Product definition This specification contains the initial, start of life dimensional, optical, mechanical and environmental performance requirements which a fully installed blown fibre protected microduct closure must meet in order for it to be categorised as an EN standard product. These products are suitable for installation of and use with microduct fibre units, microduct optical fibre cables, microduct and protected microduct as defined within EN 60794-5. 1.2 Operating environment The tests selected combined with the severities and duration are representative of an outside plant for subterranean and/or aerial environment defined by: - ETSI EN 300 019 series: Class 8.1: underground locations (without earthquake requirement); - EN 61753-1: Category S: subterranean environment; Category A: aerial environment. 1.3 Reliability Whilst the anticipated service life expectancy of the product in this environment is a minimum of 20 years, compliance with this specification does not guarantee the reliability of the product. This should be predicted using a recognised reliability assessment programme. 1.4 Quality assurance Compliance with this specification does not guarantee the manufacturing consistency of the product. This should be maintained using a recognised quality assurance programme. 1.5 Allowed fibre and cable types This closure standard covers all IEC standard optical fibre microducts, and protected microducts with their various fibre capacities, types and designs. This includes, but is not limited to, optical fibre cable standard EN 60794-5. This product specification has only considered protected microduct cables containing microducts of same outside diameters. There are other hybrid protected microduct cables with microducts of differing OD\'s, with too many variants to be included in this PS. 1.6 Allowed microduct connector types This closure standard covers all EN standard microduct connectors, including: straight, reducer/enlarger stem, reducer/enlarger, close down, liquid block, liquid block with barb end, and end stop connectors. This includes, but is not limited to, EN 50411-2-8. 1.7 Microduct storage constraints Microduct excess storage is not required in all air blown fibre closures. Some closure types do not have sufficient internal space to provide storage. The need for microduct storage is provided inside the closure when opened, typically to ensure that there is enough microduct to fulfil the following functions: - remove the coiled microduct attached to the \'closedown\' connectors, to a remote location, close to blowing equipment, in the process uncoiling the microducts to aid blowing; - provide additional microduct if repeated cut backs for connectors are planned or likely to be fitted throughout the closure life. The minimum microduct storage bend radius is based on the outside diameter and material selection, typically based on 12 times the outside diameter (below 8 mm) and 20 times above. During fibre blowing the bend radius is typically 20 times the microduct diameter.