BS EN 61076-5:2001

1 Scope and object
2 General
   2.1 Normative references
   2.2 Marking
   2.3 Information to be given in a detail
        specification
   2.4 Standard values
   2.5 Classification
        2.5.1 Termination types
        2.5.2 Contact style
        2.5.3 Insulator body configuration
        2.5.4 Decoupling capacitor
3 Quality assessment procedures
   3.1 General
   3.2 Primary stage of manufacturing
   3.3 Structurally similar sockets
   3.4 Lot-by-lot inspection tests
   3.5 Periodic inspection tests
   3.6 Alternative test methods
4 Test methods and procedures
   4.1 General aspects
   4.2 Pre-conditioning
   4.3 Mounting of specimens
5 Supplementary test information
   5.1 Test conditions
   5.2 Mechanical tests
        5.2.1 Mating force for all socket sizes
               (insertion and withdrawal forces)
        5.2.2 Mechanical operation
        5.2.3 Contact retention
        5.2.4 Vibration
        5.2.5 Mechanical shock
        5.2.6 Terminal strength (robustness of
               terminations)
        5.2.7 Solder wicking (under consideration)
   5.3 Electrical tests
        5.3.1 Insulation resistance
        5.3.2 Voltage proof
        5.3.3 Contact resistance - Millivolt level
               method
        5.3.4 Capacitance
        5.3.5 Inductance (under consideration)
   5.4 Environmental tests
        5.4.1 Solderability
        5.4.2 Resistance to soldering heat
        5.4.3 Damp heat
        5.4.4 Dry heat
        5.4.5 Rapid change of temperature (thermal
               shock)
        5.4.6 Corrosive atmosphere or mixed flowing gas
               or harsh environment (gas tightness)
        5.4.7 Mould growth (fungus)
        5.4.8 Porosity (under consideration)
        5.4.9 Examination of dimensions and mass
        5.4.10 Visual examination
6 Packaging requirements
   6.1 Unit packing
7 Test schedule
   7.1 General
        7.1.1 Basic(minimum) test schedule
        7.1.2 Full test schedule
Annex A (informative) - Terminology
Annex B (normative) - Test method for determination of
        gas-tight characteristics for electrical
        connectors, sockets and/or contact systems
Annex ZA (normative) - Normative references to international
         publications with their corresponding European
         publications

Covers sockets for packages with contacts having one of the following in-line formats - 1) Single in-line sockets; 2) Dual in-line sockets; 3) Quad in-line sockets; 4) Zig-zag in-line (staggered) sockets. Also describes a unified numbering system, functional levels, standard test methods and gauges for use in the examination of these sockets.

This part of IEC 61000 defines the immunity test methods and range of preferred test levels for electrical and electronic equipment connected to low-voltage power supply networks for voltage dips, short interruptions, and voltage variations. This standard applies to electrical and electronic equipment having a rated input current exceeding 16 A per phase. It covers equipment installed in residential areas as well as industrial machinery, specifically voltage dips and short interruptions for equipment connected to either 50 Hz or 60 Hz a.c. networks, including 1-phase and 3-phase mains. The object of this standard is to establish a common reference for evaluating the immunity of electrical and electronic equipment when subjected to voltage dips, short interruptions and voltage variations. The test method documented in this part of IEC 61000 describes a consistent method to assess the immunity of equipment or a system against a defined phenomenon. It has the status of a Basic EMC Publication in accordance with IEC Guide 107.