BS EN 62329-3-102:2010
Current
The latest, up-to-date edition.
Heat-shrinkable moulded shapes Specification requirements for shape dimensions, material requirements and compatibility performance. Heat-shrinkable elastomeric moulded shapes, semi-rigid, material requirements and system performance
Hardcopy , PDF
English
28-02-2011
Foreword
INTRODUCTION
1 Scope
2 Normative references
3 Designation
4 Conditions of test for the moulded shapes
5 Requirements
6 Moulded shapes material conformance
7 Moulded shapes compatibility
Annex A (informative) - Adhesive compatibility guide for
sheet 102 moulded shapes
Annex ZA (normative) - Normative references to international
publications with their corresponding European
publications
Defines the requirements for heat-shrinkable elastomeric moulded shape, semi-rigid material requirements and system performance.
| Committee |
GEL/15/5
|
| DevelopmentNote |
Supersedes 09/30198650 DC. (02/2011)
|
| DocumentType |
Standard
|
| Pages |
14
|
| PublisherName |
British Standards Institution
|
| Status |
Current
|
| Supersedes |
This sheet of IEC 62329-3 gives the requirements for heat-shrinkable elastomeric moulded shape, semi-rigid material requirements and system performance.
Experience of product performance indicates that this moulded shape material is suitable for inclusion in systems for operation in the following temperature ranges: –75 °C to + 120 °C.
The moulded shapes may be supplied with a pre-coated adhesive. Refer to the manufacturers/suppliers for options. A guide to adhesive compatibility is given in Annex A.
These moulded shapes are normally supplied in the styles and dimensions given in IEC 62329-3-100. The colour is normally Black.
Styles and dimensions other than those specifically listed in IEC 62329-3-100 may be available as custom items. These items shall be considered to comply with this standard if they comply with the property requirements listed in Table 1 with the exception of dimensions.
Materials that conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone.
| Standards | Relationship |
| EN 60464-3-2:2001/A1:2006 | Identical |
| I.S. EN 62329-3-102:2010 | Equivalent |
| EN 62329-3-102:2010 | Identical |
| IEC 62329-3-102:2010 | Identical |
| UNE-EN 62329-3-102:2010 | Equivalent |
| EN 62329-1:2006/corrigendum:2006 | HEAT SHRINKABLE MOULDED SHAPES - PART 1: DEFINITIONS AND GENERAL REQUIREMENTS |
| EN 62329-3-100:2010 | Heat-shrinkable moulded shapes - Part 3: Specification requirements for shape dimensions, material requirements and compatibility performance - Sheet 100: Heat-shrinkable moulded shape dimensions |
| EN 62329-2:2006 | Heat shrinkable moulded shapes - Part 2: Methods of test |
| IEC 62329-1:2005 | Heat shrinkable moulded shapes - Part 1: Definitions and general requirements |
| IEC 60757:1983 | Code for designation of colours |
| HD 457 : 200S1 | CODE FOR DESIGNATION OF COLOURS |
| IEC 60695-11-10:2013 | Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods |
| IEC 62329-2:2006 | Heat-shrinkable moulded shapes - Part 2: Methods of test |
| IEC 62329-3-100:2010 | Heat-shrinkable moulded shapes - Part 3: Specification requirements for shape dimensions, material requirements and compatibility performance - Sheet 100: Heat-shrinkable moulded shape dimensions |
| ISO 1817:2015 | Rubber, vulcanized or thermoplastic — Determination of the effect of liquids |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.