BS ISO 12151-1 : 2010
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
CONNECTIONS FOR HYDRAULIC FLUID POWER AND GENERAL USE - HOSE FITTINGS - PART 1: HOSE FITTINGS WITH ISO 8434-3 O-RING FACE SEAL ENDS
Hardcopy , PDF
English
01-01-2010
18-08-2020
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Performance requirements
5 Designation of hose fittings
6 Design
7 Manufacture
8 Assembly instructions
9 Procurement information
10 Marking
11 Identification statement (reference to this part of
ISO 12151)
Annex A (informative) - Illustrations of applications for
short, medium and long ISO 12151-1 hose fittings
Bibliography
Defines the general and dimensional requirements for the design and performance of hose fittings with O-ring face seal ends in accordance with ISO 8434-3, made of carbon steel, for nominal hose inside diameters of 6,3 mm to 38 mm, inclusive, in accordance with ISO 4397.
| Committee |
MCE/18/-/4
|
| DevelopmentNote |
Supersedes 93/712221 DC. (07/2005) Supersedes 07/30163197 DC. (07/2010) 2010 Edition Re-issued in April 2017 & incorporates AMD 1 2017. (04/2017)
|
| DocumentType |
Standard
|
| Pages |
26
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| ISO 12151-1:2010 | Identical |
| ISO 4039-1:1998 | Road vehicles — Pneumatic braking systems — Part 1: Pipes, male fittings and tapped holes with facial sealing surface |
| ISO 3862:2017 | Rubber hoses and hose assemblies — Rubber-covered spiral-wire-reinforced hydraulic types for oil-based or water-based fluids — Specification |
| ISO 68-2:1998 | ISO general purpose screw threads — Basic profile — Part 2: Inch screw threads |
| ISO 3949:2009 | Plastics hoses and hose assemblies — Textile-reinforced types for hydraulic applications — Specification |
| ISO 5598:2008 | Fluid power systems and components — Vocabulary |
| ISO 4759-1:2000 | Tolerances for fasteners — Part 1: Bolts, screws, studs and nuts — Product grades A, B and C |
| ISO 6605:2017 | Hydraulic fluid power — Test methods for hoses and hose assemblies |
| ISO 4397:2011 | Fluid power connectors and associated components — Nominal outside diameters of tubes and nominal hose sizes |
| ISO 4039-2:1998 | Road vehicles — Pneumatic braking systems — Part 2: Pipes, male fittings and holes with conical sealing surface |
| ISO 5864:1993 | ISO inch screw threads — Allowances and tolerances |
| ISO 4038:1996 | Road vehicles — Hydraulic braking systems — Simple flare pipes, tapped holes, male fittings and hose end fittings |
| ISO 4079:2017 | Rubber hoses and hose assemblies — Textile-reinforced hydraulic types for oil-based or water-based fluids — Specification |
| ISO 8434-3:2005 | Metallic tube connections for fluid power and general use — Part 3: O-ring face seal connectors |
| ISO 19879:2010 | Metallic tube connections for fluid power and general use — Test methods for hydraulic fluid power connections |
| ISO 6149-1:2006 | Connections for hydraulic fluid power and general use — Ports and stud ends with ISO 261 metric threads and O-ring sealing — Part 1: Ports with truncated housing for O-ring seal |
| ISO 9227:2017 | Corrosion tests in artificial atmospheres — Salt spray tests |
| ISO 1436:2017 | Rubber hoses and hose assemblies — Wire-braid-reinforced hydraulic types for oil-based or water-based fluids — Specification |
| ISO 263:1973 | ISO inch screw threads — General plan and selection for screws, bolts and nuts — Diameter range 0,06 to 6 in |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.