CEI EN 61340-2-3 : 2000
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Electrostatics Part 2-3: Test methods for the determination of resistance and resistivity of planar solid materials used to prevent the accumulation of electrostatic charges
Hardcopy , PDF
English - Italian
01-10-2000
15-11-2024
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Conditioning and test environment
5 Selection of test method
6 Resistance measurements for solid conductive materials
7 Resistance measurements for solid insulating materials
8 Resistance measurements for planar electrostatic dissipative
materials (used to avoid electrostatic charge accumulation)
9 Conversion to resistivity values
10 Resistance measurements for non-planar materials and
products with small structures
11 Repeatability and reproducibility
12 Test report
Annex A (normative) - System verification
Annex ZA (normative) - Normative references to international
publications with their corresponding European
publications
This standard describes test methods for determining the electrical resistance and resistivity of solid materials in the range 104 W to 1012 W used to prevent the build-up of electrostatic charges.
| Committee |
CT 101
|
| DevelopmentNote |
Classificazione CEI 101-2 (08/2001) 1ED 2000 Edition is valid until 28-07-2019. (04/2017) Italian translation issued on 01.07.2017. (08/2017)
|
| DocumentType |
Standard
|
| Pages |
26
|
| PublisherName |
Comitato Elettrotecnico Italiano
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| EN 61340-2-3:2016 | Identical |
| IEC 61340-2-3:2016 | Identical |
| EN 61340-2-3:2000 | Identical |
| IEC 61340-2-3:2000 | Identical |
| ISO 7619-1:2010 | Rubber, vulcanized or thermoplastic — Determination of indentation hardness — Part 1: Durometer method (Shore hardness) |
| ISO 3915:1981 | Plastics — Measurement of resistivity of conductive plastics |
| IEC 62631-3-3:2015 | Dielectric and resistive properties of solid insulating materials - Part 3-3: Determination of resistive properties (DC methods) - Insulation resistance |
| IEC 62631-3-2:2015 | Dielectric and resistive properties of solid insulating materials - Part 3-2: Determination of resistive properties (DC methods) - Surface resistance and surface resistivity |
| IEC 62631-3-1:2016 | Dielectric and resistive properties of solid insulating materials - Part 3-1: Determination of resistive properties (DC methods) - Volume resistance and volume resistivity - General method |
| EN 62631-3-2:2016 | Dielectric and resistive properties of solid insulating materials - Part 3-2: Determination of resistive properties (DC Methods) - Surface resistance and surface resistivity |
| EN 62631-3-1:2016 | Dielectric and resistive properties of solid insulating materials - Part 3-1: Determination of resistive properties (DC methods) - Volume resistance and volume resistivity - General method |
| EN 62631-3-3:2016 | Dielectric and resistive properties of solid insulating materials - Part 3-3: Determination of resistive properties (DC Methods) - Insulation resistance |
| ISO 1853:2011 | Conducting and dissipative rubbers, vulcanized or thermoplastic — Measurement of resistivity |
| EN ISO 3915:1999 | Plastics - Measurement of resistivity of conductive plastics (ISO 3915:1981) |
| ISO 2951:2012 | Rubber, vulcanized or thermoplastic — Determination of insulation resistance |