DEFSTAN 80-16/3(2002) : 2002
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PAINT REMOVER, DICHLOROMETHANE, WATER RINSABLE - TYPE 1: HIGH VISCOSITY (BRUSHING) TYPE 2: LOW VISCOSITY (SPRAYING)
12-01-2013
29-09-2006
Description
Content
Preface
Main Text
SECTION 1 - GENERAL REQUIREMENTS
0 Introduction
1 Scope
2 Warning
3 Related Documents
4 Description
5 Information to be Supplied by the Purchaser
6 Keeping Qualities
7 Quality Assurance
8 Product Conformity Certification
9 Containers and Marking of Containers
SECTION 2 - MATERIAL
10 Composition
11 Testing
ANNEX A - Determination of Viscosity
ANNEX B - Determination of Rate of Evaporation
ANNEX C - Determination of Freedom from Corrosive Action
ANNEX D - Determination of Paint Removing Power
ANNEX E - Determination of Flammability
ANNEX F - Determination of Water Rinsability
ANNEX G - Determination of Stress Corrosion Cracking
Specifies requirements for a dichloromethane water rinsable paint remover in two types: - Type 1, High viscosity (Brushing), and - Type 2, Low viscosity (Spraying).
| DevelopmentNote |
Supersedes DEFSTAN 80-16/2(1993), DEFSTAN 80-16/1(1970) & DEF 1280. (07/2002)
|
| DocumentType |
Standard
|
| PublisherName |
UK Ministry of Defence Standards
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| DEFSTAN 03-23(PT1)/1(1993) : 1993 | GUIDE TO THE SELECTION OF PAINT REMOVAL METHODS - PART 1: CHEMICAL PAINT REMOVERS |
| DEFSTAN 21-5/1(2000) : 2000 | CODE OF PRACTICE FOR PROTECTIVE FINISHES |
| DEFSTAN 80-196/1(1994) : 1994 | PAINT REMOVER, TRICHLOROETHYLENE BASED, WATER RINSABLE TYPE: BRUSHING |
| BS EN ISO 1514:2004 | Paints and varnishes. Standard panels for testing |
| BS EN ISO 1518:2001 | Paints and varnishes. Scratch test |
| DEFSTAN 03-19/2(1994) : 1994 | ELECTRO-DEPOSITION OF CADMIUM |
| BS EN ISO 3696:1995 | Water for analytical laboratory use. Specification and test methods |
| BS EN 23270:1991 | Specification for temperatures and humidities for conditioning and testing paints, varnishes and their raw materials |
| BS X 34:1992 | Specification for air drying, two component, polyurethane finish for aerospace purposes |
| BS 2L 97:1971 | Specification for plate of aluminium-copper-magnesium-manganese alloy (solution treated, controlled stretched and aged at room temperature) (Cu 4.4, Mg 1.5, Mn 0.6) |
| BS EN 10130:2006 | Cold rolled low carbon steel flat products for cold forming. Technical delivery conditions |
| BS EN 1652:1998 | Copper and copper alloys. Plate, sheet, strip and circles for general purposes |
| BS 3370:1970 | Specification for wrought magnesium alloys for general engineering purposes. Plate, sheet and strip |
| BS 2L 500:1973 | Procedure for inspection and testing of wrought magnesium-base alloys |
| BS EN 45014:1998 | General criteria for supplier\'s declaration of conformity |
| BS X 33:1991 | Specification for two component epoxy primer for aerospace purposes |
| BS L 168:1978 | Specification for bars and extruded sections of aluminium-copper-magnesium-silicon-manganese alloy (solution treated and artificially aged) (not exceeding 200 mm diameter or minor sectional dimension) (Cu 4.4, Mg 0.5, Si 0.7, Mn 0.8) |
| DEFSTAN 03-2/3(1995) : 1995 | CLEANING AND PREPARATION OF METAL SURFACES |
| DEFSTAN 91-16/2(1982) : 1982 | WAX, PARAFFIN, ORDINARY WAX, PARAFFIN, LF QUALITY WAX, PARAFFIN, SPECIAL |