DIN EN 12007-2:2012-10
Current
The latest, up-to-date edition.
GAS INFRASTRUCTURE - PIPELINES FOR MAXIMUM OPERATING PRESSURE UP TO AND INCLUDING 16 BAR - PART 2: SPECIFIC FUNCTIONAL REQUIREMENTS FOR POLYETHYLENE (MOP UP TO AND INCLUDING 10 BAR)
Hardcopy , PDF
English
01-01-2012
Foreword
1 Scope
2 Normative references
3 Definitions and abbreviations
4 Design
4.1 General
4.2 Materials and components
4.3 Maximum operating pressure
4.4 Assembly techniques
4.5 Material properties for flow stopping by
squeeze-off
4.6 Pipework inside building
5 Construction
5.1 Storage, handling and transportation
5.2 Jointing
5.3 Laying
5.4 Connection to existing systems
6 Quality control
6.1 Inspection prior to installation
6.2 Inspection during laying
7 Pressure testing
Annex A (informative) Storage, handling and transportation
Annex B (informative) Fusion joint integrity
Annex C (informative) Bibliography
Décrit spécifiquement les recommandations fonctionnelles pour Les pipelines du polyéthylène (PE) avec le général fonctionnel Recommandations d'EN 12007-1. Pertinent pour un maximum fonctionnant Contraignez (MOP) vers le haut à et incluant 10 barre, et un fonctionnant Température dans la gamme des degrés de -20 C et degrés de +40 C.
| DevelopmentNote |
Supersedes DIN EN 12008-1 (08/2000)
|
| DocumentType |
Standard
|
| Pages |
30
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| NF EN 12007-2 : 2012 | Identical |
| NBN EN 12007-2 : 2012 | Identical |
| NEN EN 12007-2 : 2012 | Identical |
| NS EN 12007-2 : 2012 | Identical |
| I.S. EN 12007-2:2012 | Identical |
| BS EN 12007-2:2012 | Identical |
| EN 12007-2:2012 | Identical |
| UNE-EN 12007-2:2013 | Identical |
| EN 12327:2012 | Gas infrastructure - Pressure testing, commissioning and decommissioning procedures - Functional requirements |
| EN 1555-1:2010 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 1: General |
| EN 1555-3:2010+A1:2012 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings |
| EN 12007-3:2015 | Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 3: Specific functional requirements for steel |
| EN 12007-1:2012 | Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 1: General functional requirements |
| ISO 10838-2:2000 | Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels — Part 2: Metal fittings for pipes of nominal outside diameter greater than 63 mm |
| ISO 21307:2011 | Plastics pipes and fittings — Butt fusion jointing procedures for polyethylene (PE) pipes and fittings used in the construction of gas and water distribution systems |
| ISO 10838-1:2000 | Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels — Part 1: Metal fittings for pipes of nominal outside diameter less than or equal to 63 mm |
| ISO 12176-1:2017 | Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 1: Butt fusion |
| ISO 3:1973 | Preferred numbers — Series of preferred numbers |
| ISO 12176-2:2008 | Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 2: Electrofusion |
| ISO 11414:2009 | Plastics pipes and fittings — Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion |
| EN 1555-4:2011 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 4: Valves |
| EN 1555-5:2010 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 5: Fitness for purpose of the system |
| EN 1555-2:2010 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 2: Pipes |
| ISO 497:1973 | Guide to the choice of series of preferred numbers and of series containing more rounded values of preferred numbers |
| EN 12007-4:2012 | Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 4: Specific functional requirements for renovation |
| ISO 11413:2008 | Plastics pipes and fittings — Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.