DIN EN 15011:2014-09
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Cranes - Bridge and gantry cranes (includes Amendment A1:2014)
Available format(s)
Hardcopy , PDF
Language(s)
German
Published date
01-09-2014
Superseded date
01-10-2021
Superseded by
$395.18
Including GST where applicable
| DevelopmentNote |
DRAFT 2017 issued in October 2017. (10/2017)
|
| DocumentType |
Standard
|
| Pages |
92
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| EN 15011:2011+A1:2014 | Identical |
| PREN 15011 : DRAFT 2017 | Identical |
| VDI 4467:2014-12 | Tandem operation of cranes/trolleys |
| VDI 3650:2013-02 | Equipment for protecting cranes against drifting caused by wind |
| VDI 4412:2016-05 | Cableless control of cranes |
| ISO 11202:2010 | Acoustics — Noise emitted by machinery and equipment — Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections |
| EN 81-43:2009 | Safety rules for the construction and installation of lifts - Special lifts for the transport of persons and goods - Part 43: Lifts for cranes |
| EN ISO 11204:2010 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections (ISO 11204:2010) |
| EN 12385-4:2002+A1:2008 | Steel wire ropes - Safety - Part 4: Stranded ropes for general lifting applications |
| EN 13557:2003+A2:2008 | Cranes - Controls and control stations |
| ISO 4871:1996 | Acoustics — Declaration and verification of noise emission values of machinery and equipment |
| ISO 11660-5:2001 | Cranes — Access, guards and restraints — Part 5: Bridge and gantry cranes |
| EN 60947-5-5 : 1997 AMD 2 2016 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 5-5: CONTROL CIRCUIT DEVICES AND SWITCHING ELEMENTS - ELECTRICAL EMERGENCY STOP DEVICE WITH MECHANICAL LATCHING FUNCTION (IEC 60947-5-5:1997/A2:2016) |
| ISO 3744:2010 | Acoustics — Determination of sound power levels and sound energy levels of noise sources using sound pressure — Engineering methods for an essentially free field over a reflecting plane |
| ISO 15513:2000 | Cranes — Competency requirements for crane drivers (operators), slingers, signallers and assessors |
| EN 13155:2003+A2:2009 | Cranes - Safety - Non-fixed load lifting attachments |
| EN 60825-1:2014/AC:2017-06 | SAFETY OF LASER PRODUCTS - PART 1: EQUIPMENT CLASSIFICATION AND REQUIREMENTS (IEC 60825-1:2014) |
| ISO 12480-1:1997 | Cranes — Safe use — Part 1: General |
| ISO 9926-1:1990 | Cranes — Training of drivers — Part 1: General |
| EN 12644-2:2000+A1:2008 | Cranes - Information for use and testing - Part 2: Marking |
| ISO 9374-5:1991 | Cranes — Information to be provided — Part 5: Overhead travelling cranes and portal bridge cranes |
| ISO/TR 11688-1:1995 | Acoustics — Recommended practice for the design of low-noise machinery and equipment — Part 1: Planning |
| EN 894-2:1997+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 2: Displays |
| IEC 60364-4-41:2005+AMD1:2017 CSV | Low voltage electrical installations - Part 4-41: Protection for safety - Protection against electric shock |
| ISO 13732-1:2006 | Ergonomics of the thermal environment — Methods for the assessment of human responses to contact with surfaces — Part 1: Hot surfaces |
| DIN 3990-1:1987-12 | CALCULATION OF LOAD CAPACITY OF CYLINDRICAL GEARS - INTRODUCTION AND GENERAL INFLUENCE FACTORS |
| EN 349:1993+A1:2008 | Safety of machinery - Minimum gaps to avoid crushing of parts of the human body |
| ISO 12488-1:2012 | Cranes — Tolerances for wheels and travel and traversing tracks — Part 1: General |
| HD 60364-4-41:2017/A11:2017 | LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 4-41: PROTECTION FOR SAFETY - PROTECTION AGAINST ELECTRIC SHOCK |
| IEC 60204-11:2000 | Safety of machinery - Electrical equipment of machines - Part 11: Requirements for HV equipment for voltages above 1 000 V a.c. or 1 500 V d.c. and not exceeding 36 kV |
| IEC 60825-1:2014 | Safety of laser products - Part 1: Equipment classification and requirements |
| IEC 60204-32:2008 | Safety of machinery - Electrical equipment of machines - Part 32: Requirements for hoisting machines |
| ISO 16881-1:2005 | Cranes — Design calculation for rail wheels and associated trolley track supporting structure — Part 1: General |
| EN 13586:2004+A1:2008 | Cranes - Access |
| EN 1050 : 1996 | SAFETY OF MACHINERY - PRINCIPLES FOR RISK ASSESSMENT |
| EN 614-1:2006+A1:2009 | Safety of machinery - Ergonomic design principles - Part 1: Terminology and general principles |
| EN ISO 13857:2008 | Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008) |
| EN ISO 11688-2:2000 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 2: Introduction to the physics of low-noise design (ISO/TR 11688-2:1998) |
| EN 12644-1:2001+A1:2008 | Cranes - Information for use and testing - Part 1: Instructions |
| ISO 12100:2010 | Safety of machinery — General principles for design — Risk assessment and risk reduction |
| ISO 9374-1:1989 | Cranes — Information to be provided — Part 1: General |
| EN ISO 13732-1:2008 | Ergonomics of the thermal environment - Methods for the assessment of human responses to contact with surfaces - Part 1: Hot surfaces (ISO 13732-1:2006) |
| EN 60204-32:2008 | Safety of machinery - Electrical equipment of machines - Part 32: Requirements for hoisting machines |
| EN ISO 11201:2010 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections (ISO 11201:2010) |
| EN 13001-2:2014 | Crane safety - General design - Part 2: Load actions |
| ISO 4309:2010 | Cranes — Wire ropes — Care and maintenance, inspection and discard |
| EN 13001-1:2015 | Cranes - General design - Part 1: General principles and requirements |
| EN ISO 3744:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010) |
| EN 953:1997+A1:2009 | Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards |
| ISO 13857:2008 | Safety of machinery — Safety distances to prevent hazard zones being reached by upper and lower limbs |
| ISO 6336-1:2006 | Calculation of load capacity of spur and helical gears — Part 1: Basic principles, introduction and general influence factors |
| ISO 11203:1995 | Acoustics — Noise emitted by machinery and equipment — Determination of emission sound pressure levels at a work station and at other specified positions from the sound power level |
| EN 13157:2004+A1:2009 | Cranes - Safety - Hand powered cranes |
| EN ISO 12100:2010 | Safety of machinery - General principles for design - Risk assessment and risk reduction (ISO 12100:2010) |
| ISO 2631-1:1997 | Mechanical vibration and shock — Evaluation of human exposure to whole-body vibration — Part 1: General requirements |
| EN 60204-11:2000/corrigendum:2010 | SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 11: REQUIREMENTS FOR HV EQUIPMENT FOR VOLTAGES ABOVE 1000 V A.C. OR 1500 V D.C. AND NOT EXCEEDING 36 KV |
| EN ISO 13849-1:2015 | Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015) |
| DIN EN ISO 1680:2014-04 | ACOUSTICS - TEST CODE FOR THE MEASUREMENT OF AIRBORNE NOISE EMITTED BY ROTATING ELECTRICAL MACHINES (ISO 1680:2013) |
| EN ISO 4871:2009 | Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996) |
| ISO 4301-1:2016 | Cranes — Classification — Part 1: General |
| ISO 22986:2007 | Cranes — Stiffness — Bridge and gantry cranes |
| EN 795:2012 | Personal fall protection equipment - Anchor devices |
| ISO 8566-5:2017 | Cranes — Cabins and control stations — Part 5: Overhead travelling and portal bridge cranes |
| EN ISO 11688-1:2009 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995) |
| ISO 13849-1:2015 | Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design |
| ISO/TR 11688-2:1998 | Acoustics — Recommended practice for the design of low-noise machinery and equipment — Part 2: Introduction to the physics of low-noise design |
| ISO 12482-1:1995 | Cranes — Condition monitoring — Part 1: General |
| EN ISO 11202:2010 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections (ISO 11202:2010) |
| EN ISO 11203:2009 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions from the sound power level (ISO 11203:1995) |
| ISO 7752-5:1985 | Lifting appliances — Controls — Layout and characteristics — Part 5: Overhead travelling cranes and portal bridge cranes |
| ISO 11201:2010 | Acoustics — Noise emitted by machinery and equipment — Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections |
| ISO 11204:2010 | Acoustics — Noise emitted by machinery and equipment — Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections |
| PREN 13001-3-3 : DRAFT 2012 | CRANES - GENERAL DESIGN - PART 3-3: LIMIT STATES AND PROOF OF COMPETENCE OF WHEEL/RAIL CONTACTS |
| ISO 10245-5:1995 | Cranes — Limiting and indicating devices — Part 5: Overhead travelling and portal bridge cranes |
| CEN/TS 13001-3-2:2008 | Cranes - General design - Part 3-2: Limit states and proof of competence of wire ropes in reeving systems |
| IEC 60947-5-5:1997+AMD1:2005+AMD2:2016 CSV | Low-voltage switchgear and controlgear - Part 5-5: Control circuitdevices and switching elements - Electrical emergency stop device with mechanical latching function |
| EN 894-1:1997+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 1: General principles for human interactions with displays and control actuators |
Summarise
$395.18
Including GST where applicable
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.