DIN EN 50134-2 : 2000
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
ALARM SYSTEMS - SOCIAL ALARM SYSTEMS - PART 2: TRIGGER DEVICES
12-01-2013
13-08-2019
Einleitung
1 Anwendungsbereich
2 Normative Verweisungen
3 Definitionen
4 Manuell aktivierte Auslösegeräte
5 Prüfungen von manuell aktivierten Auslösegeräten
6 Automatisch aktivierte Auslösegeräte
7 Kennzeichnung
Anhang A (normativ) Messungen der Kontakt- und
Isolationswiderstände für mechanische
Kontaktfunktionen
Anhang B (normativ) Spannvorrichtung für die Prüfung der
Zugentlastung
Anhang C (normativ) Prüfaufbau, wenn HF-geschirmte
Prüfeinrichtungen eingesetzt werden
Defines tests and requirements for manually-activated trigger devices that form part of a social alarm system. Only applicable to manually-activated trigger devices that transmit the alarm triggering signal to a local controller or unit by cable or wire-free radio transmission, for example; push button fixed/ pull switch fixed/ push button portable/ pull activated portable. Gives a guide on automatically-activated trigger devices, and for the tests and requirements applicable to these, refer to appropriate CEN/CENELEC standards for gas alarm, fire alarm and intruder alarm system components. Not specific to EMC emission or electrical safety requirements.
| DevelopmentNote |
Supersedes DIN EN 50134-2-1. (10/2001) DRAFT 2016 issued in September 2016. (09/2016)
|
| DocumentType |
Standard
|
| PublisherName |
Verband Deutscher Elektrotechniker
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| I.S. EN 50134-2:1999 | Identical |
| BS EN 50134-2:2000 | Identical |
| NBN EN 50134-2 : 2000 | Identical |
| VDE 0830-4-2 : 2000 | Corresponds |
| UNE-EN 50134-2:2000 | Identical |
| BS EN 50134-2:2017 | Identical |
| I.S. EN 50134-2:2017 | Identical |
| EN 50134-2:2017 | Identical |
| VDE 0830-4-2 : 2000 | Identical |
| NF EN 50134-2 : 2017 | Identical |
| NEN EN 50134-2 : 2017 | Identical |
| EN 50058:1998 | Electrical apparatus for the detection and measurement of combustible gases - Performance requirements for Group II apparatus indicating up to 100 % (v/v) gas |
| DIN IEC 61020-5-1:1994-02 | Electromechanical switches for use in electronic equipment; part 5: sectional specification for pushbutton switches; section 1: blank detail specification; identical with IEC 61020-5-1:1991 |
| VDE 0830-1-4:2015-04 | Alarm systems Part 4: Electromagnetic compatibility – Product family standard: Immunity requirements for components of fire, intruder, hold up, CCTV, access control and social alarm systems; |
| EN 50054:1998 | Electrical apparatus for the detection and measurement of combustible gases - General requirements and test methods |
| IEC 60341-1:1970 | Push-button switches - Part 1: General requirements and measuring methods |
| EN 60068-1:2014 | Environmental testing - Part 1: General and guidance |
| EN 50055:1998 | Electrical apparatus for the detection and measurement of combustible gases - Performance requirements for Group I apparatus indicating up to 5 % (v/v) methane in air |
| EN 50057:1998 | Electrical apparatus for the detection and measurement of combustible gases - Performance requirements for Group II apparatus indicating up to 100 % lower explosive limit |
| VDE 0830-1-5:2012-02 | |
| DIN EN 60068-1:2015-09 | ENVIRONMENTAL TESTING - PART 1: GENERAL AND GUIDANCE (IEC 60068-1:2013) |
| DIN EN 50130-4:2015-04 | ALARM SYSTEMS - PART 4: ELECTROMAGNETIC COMPATIBILITY - PRODUCT FAMILY STANDARD: IMMUNITY REQUIREMENTS FOR COMPONENTS OF FIRE, INTRUDER, HOLD UP, CCTV, ACCESS CONTROL AND SOCIAL ALARM SYSTEMS |
| ETSI EN 300 220-2 V2.4.1 (2012-05) | Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD); Radio equipment to be used in the 25 MHz to 1 000 MHz frequency range with power levels ranging up to 500 mW; Part 2: Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive |
| DIN EN 50130-5:2012-02 | ALARM SYSTEMS - PART 5: ENVIRONMENTAL TEST METHODS |
| EN 50130-4:2011/A1:2014 | ALARM SYSTEMS - PART 4: ELECTROMAGNETIC COMPATIBILITY - PRODUCT FAMILY STANDARD: IMMUNITY REQUIREMENTS FOR COMPONENTS OF FIRE, INTRUDER, HOLD UP, CCTV, ACCESS CONTROL AND SOCIAL ALARM SYSTEMS |
| EN 50056:1998 | Electrical apparatus for the detection and measurement of combustible gases - Performance requirements for Group I apparatus indicating up to 100 % (v/v) methane in air |
| DIN EN 300220-2:2017-05 | SHORT RANGE DEVICES (SRD) OPERATING IN THE FREQUENCY RANGE 25 MHZ TO 1000 MHZ - PART 2: HARMONISED STANDARD COVERING THE ESSENTIAL REQUIREMENTS OF ARTICLE 3.2 OF THE DIRECTIVE 2014/53/EU FOR NON SPECIFIC RADIO EQUIPMENT |
| EN 50130-5:2011 | Alarm systems - Part 5: Environmental test methods |
| DIN IEC 61020-5:1994-02 | Electromechanical switches for use in electronic equipment; part 5: sectional specification for pushbutton switches; identical with IEC 61020-5:1991 |