DIN ISO 7919-2:2010-06
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
MECHANICAL VIBRATION - EVALUATION OF MACHINE VIBRATION BY MEASUREMENTS ON ROTATING SHAFTS - PART 2: LAND-BASED STEAM TURBINES AND GENERATORS IN EXCESS OF 50 MW WITH NORMAL OPERATING SPEEDS OF 1500 R/MIN, 1800 R/MIN, 3000 R/MIN AND 3600 R/MIN
Hardcopy , PDF
English
01-01-2010
01-01-2018
Foreword
Introduction
1 Scope
2 Normative references
3 Measurement procedure
4 Evaluation criteria
Annex A (normative) Evaluation zones boundaries
Annex B (informative) Evaluation zone boundary values
and bearing clearance
Bibliography
Specifies provisions for evaluating the severity of in-situ, broad-band shaft vibration measured radial (i.e. transverse) to the shaft axis at, or close to, the main bearings. These are in terms of: - vibration under normal steady-state operating conditions; - vibration during other (non-steady-state) conditions when transient changes are taking place, including run up or run down, initial loading and load changes; - changes in vibration which can occur during normal steady-state operation.
| DocumentType |
Standard
|
| Pages |
17
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| ISO 7919-2:2009 | Identical |
| DIN ISO 10816-7:2009-08 | MECHANICAL VIBRATION - EVALUATION OF MACHINE VIBRATION BY MEASUREMENTS ON NON-ROTATING PARTS - PART 7: ROTODYNAMIC PUMPS FOR INDUSTRIAL APPLICATIONS, INCLUDING MEASUREMENTS ON ROTATING SHAFTS |
| DIN ISO 11342:1999-05 | MECHANICAL VIBRATION - METHODS AND CRITERIA FOR THE MECHANICAL BALANCING OF FLEXIBLE ROTORS |
| DIN ISO 13373-3:2015-12 | CONDITION MONITORING AND DIAGNOSTICS OF MACHINES - VIBRATION CONDITION MONITORING - PART 3: GUIDELINES FOR VIBRATION DIAGNOSIS (ISO 13373-3:2015) |
| VDI 3840:2004-05 | Vibration analysis for machine sets |
| VDI 3839 Blatt 5:2001-09 | Instructions on measuring and interpreting the vibration of machines - Typical vibration patterns with electrical machines |
| VDI 3840:2004-05 | VIBRATION ANALYSIS FOR MACHINE SETS |
| VDI 2038 Blatt 1:2012-06 | Serviceability of structures under dynamic loads - Methods of analysis and evaluation in structural dynamics - Basics, methods, procedures and loads |
| VDI 3839 Blatt 1:2001-03 | Instructions on measuring and interpreting the vibrations of machines - General principles |
| DIN ISO 17359:2011-09 | CONDITION MONITORING AND DIAGNOSTICS OF MACHINES - GENERAL GUIDELINES |
| DIN ISO 18436-2:2014-11 | CONDITION MONITORING AND DIAGNOSTICS OF MACHINES - REQUIREMENTS FOR QUALIFICATION AND ASSESSMENT OF PERSONNEL - PART 2: VIBRATION CONDITION MONITORING AND DIAGNOSTICS (ISO 18436-2:2014) |
| DIN ISO 20816-1:2015-12 (Draft) | MECHANICAL VIBRATION - MEASUREMENT AND EVALUATION OF MACHINE VIBRATION - PART 1: GENERAL GUIDELINES (ISO 20816-1:2016) |
| DIN ISO 21940-12:2016-09 | MECHANICAL VIBRATION - ROTOR BALANCING - PART 12: PROCEDURES AND TOLERANCES FOR ROTORS WITH FLEXIBLE BEHAVIOUR (ISO 21940-12:2016) |
| DIN ISO 11342 E : 1999 | MECHANICAL VIBRATION - METHODS AND CRITERIA FOR THE MECHANICAL BALANCING OF FLEXIBLE ROTORS |
| DIN ISO 10817-1:1999-11 | ROTATING SHAFT VIBRATION MEASURING SYSTEMS - PART 1: RELATIVE AND ABSOLUTE SENSING OF RADIAL VIBRATION |
| DIN ISO 7919-4:2010-06 | MECHANICAL VIBRATION - EVALUATION OF MACHINE VIBRATION BY MEASUREMENTS ON ROTATING SHAFTS - PART 4: GAS TURBINE SETS WITH FLUID-FILM BEARINGS (ISO 7919-4:2009 + AMD.1:2017) |
| ISO 10816-4:2009 | Mechanical vibration — Evaluation of machine vibration by measurements on non-rotating parts — Part 4: Gas turbine sets with fluid-film bearings |
| ISO 13373-1:2002 | Condition monitoring and diagnostics of machines — Vibration condition monitoring — Part 1: General procedures |
| DIN ISO 10816-7:2009-08 | MECHANICAL VIBRATION - EVALUATION OF MACHINE VIBRATION BY MEASUREMENTS ON NON-ROTATING PARTS - PART 7: ROTODYNAMIC PUMPS FOR INDUSTRIAL APPLICATIONS, INCLUDING MEASUREMENTS ON ROTATING SHAFTS |
| DIN ISO 7919-5:2005-10 | MECHANICAL VIBRATION - EVALUATION OF MACHINE VIBRATION BY MEASUREMENTS ON ROTATING SHAFTS - PART 5: MACHINE SETS IN HYDRAULIC POWER GENERATING AND PUMPING PLANTS |
| DIN ISO 7919-1:1997-08 | MECHANICAL VIBRATION OF NON-RECIPROCATING MACHINES - MEASUREMENTS ON ROTATING SHAFTS AND EVALUATION - PART 1: GENERAL GUIDELINES |
| ISO 10816-2:2009 | Mechanical vibration — Evaluation of machine vibration by measurements on non-rotating parts — Part 2: Land-based steam turbines and generators in excess of 50 MW with normal operating speeds of 1 500 r/min, 1 800 r/min, 3 000 r/min and 3 600 r/min |
| ISO 10814:1996 | Mechanical vibration — Susceptibility and sensitivity of machines to unbalance |
| ISO 7919-1:1996 | Mechanical vibration of non-reciprocating machines — Measurements on rotating shafts and evaluation criteria — Part 1: General guidelines |
| ISO 10816-5:2000 | Mechanical vibration — Evaluation of machine vibration by measurements on non-rotating parts — Part 5: Machine sets in hydraulic power generating and pumping plants |
| ISO 13373-2:2016 | Condition monitoring and diagnostics of machines — Vibration condition monitoring — Part 2: Processing, analysis and presentation of vibration data |
| ISO 2041:2009 | Mechanical vibration, shock and condition monitoring — Vocabulary |
| DIN ISO 13373-2:2006-01 | CONDITION MONITORING AND DIAGNOSTICS OF MACHINES - VIBRATION CONDITION MONITORING - PART 2: PROCESSING, ANALYSIS AND PRESENTATION OF VIBRATION DATA (ISO 13373-2:2016) |
| DIN ISO 10817-1:1999-11 | ROTATING SHAFT VIBRATION MEASURING SYSTEMS - PART 1: RELATIVE AND ABSOLUTE SENSING OF RADIAL VIBRATION |
| ISO 10816-1:1995 | Mechanical vibration — Evaluation of machine vibration by measurements on non-rotating parts — Part 1: General guidelines |
| DIN ISO 7919-3:2009-08 | MECHANICAL VIBRATION - EVALUATION OF MACHINE VIBRATION BY MEASUREMENTS ON ROTATING SHAFTS - PART 3: COUPLED INDUSTRIAL MACHINES (ISO 7919-3:2009 + AMD.1:2017) |
| ISO 10816-7:2009 | Mechanical vibration — Evaluation of machine vibration by measurements on non-rotating parts — Part 7: Rotodynamic pumps for industrial applications, including measurements on rotating shafts |
| ISO 10817-1:1998 | Rotating shaft vibration measuring systems — Part 1: Relative and absolute sensing of radial vibration |
| ISO 5348:1998 | Mechanical vibration and shock — Mechanical mounting of accelerometers |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.