EEMUA 225 : 1920
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
ABOVE GROUND PLASTIC TANKS - A GUIDE TO THEIR SPECIFICATION, INSTALLATION, COMMISSIONING, INSPECTION, MAINTENANCE, REPAIR AND DISPOSAL
01-01-1920
30-06-2022
1 Scope
2 Materials
3 Design issues
4 Nameplates, data book, and management of change
5 Installation, commissioning, and operation within
the design window
6 Degradation mechanisms and failure modes
7 Inspection methods and NDT techniques
8 Deciding end-of-life, repairs, modification
and recommissioning
9 Decommissioning, mothballing, reuse and disposal
Appendix 1 - Example nameplates
Appendix 2 - Example management of change form and checklist
Appendix 3 - Recommended bolt tightening torques for flanges
Appendix 4 - Example commissioning check list
Appendix 5 - Risk-based inspection frequencies for tanks
containing potentially aggressive contents
Appendix 6 - Example Inspection Record Form
Appendix 7 - Detectable defects, applicable inspection
techniques, and possible actions
Bibliography
Describes a range of topics, from how to specify the design, through inspection, maintenance, and repair, to decisions at end-of-life and safe disposal.
| DocumentType |
Standard
|
| PublisherName |
Engineering Equipment Material Users Association
|
| Status |
Superseded
|
| SupersededBy |
| EN 13121-1:2003 | GRP tanks and vessels for use above ground - Part 1: Raw materials - Specification conditions and acceptance conditions |
| EN 12573-3:2000 | Welded static non-pressurized thermoplastic tanks - Part 3: Design and calculation for single skin rectangular tanks |
| EN 13121-3:2016 | GRP tanks and vessels for use above ground - Part 3: Design and workmanship |
| API 2000 : 2014 | VENTING ATMOSPHERIC AND LOW-PRESSURE STORAGE TANKS |
| EN 12573-2:2000 | Welded static non-pressurised thermoplastic tanks - Part 2: Calculation of vertical cylindrical tanks |
| BS 4994:1987 | Specification for design and construction of vessels and tanks in reinforced plastics |
| EN 13341:2005+A1:2011 | Static thermoplastic tanks for above ground storage of domestic heating oils, kerosene and diesel fuels - Blow moulded and rotationally moulded polyethylene tanks and rotationally moulded tanks made of anionically polymerized polyamide 6 - Requirements and test methods |
| EN 12573-1:2000 | Welded static non-pressurized thermoplastic tanks - Part 1: General principles |
| EN 13121-2:2003 | GRP tanks and vessels for use above ground - Part 2: Composite materials - Chemical resistance |
| EN 13923:2005 | Filament-wound FRP pressure vessels - Materials, design, manufacturing and testing |
| EN 1778:1999 | Characteristic values for welded thermoplastics constructions - Determination of allowable stresses and moduli for design of thermoplastics equipment |
| ASME PV CODE 10 : 2017 | BOILER AND PRESSURE VESSEL CODE - FIBER-REINFORCED PLASTIC PRESSURE VESSELS |
| API 2350 : 2012 | OVERFILL PROTECTION FOR STORAGE TANKS IN PETROLEUM FACILITIES |
| EN ISO 14122-3:2016 | Safety of machinery - Permanent means of access to machinery - Part 3: Stairs, stepladders and guard-rails (ISO 14122-3:2016) |
| EN ISO 14122-4:2016 | Safety of machinery - Permanent means of access to machinery - Part 4: Fixed ladders (ISO 14122-4:2016) |
| EN ISO 14122-2:2016 | Safety of machinery - Permanent means of access to machinery - Part 2: Working platforms and walkways (ISO 14122-2:2016) |
| EN 12573-4:2000 | Welded static non-pressurised thermoplastic tanks - Part 4: Design and calculation of flanged joints |
| EN 13067:2012 | Plastics welding personnel - Qualification testing of welders - Thermoplastics welded assemblies |
| EN ISO 14122-1:2016 | Safety of machinery - Permanent means of access to machinery - Part 1: Choice of fixed means and general requirements of access (ISO 14122-1:2016) |
| ASME RTP 1 : 2015 | REINFORCED THERMOSET PLASTIC CORROSION-RESISTANT EQUIPMENT |