• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

EN 14483-4 : 2004

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

VITREOUS AND PORCELAIN ENAMELS - DETERMINATION OF RESISTANCE TO CHEMICAL CORROSION - PART 4: DETERMINATION OF RESISTANCE TO CHEMICAL CORROSION BY ALKALINE LIQUIDS USING A CYLINDRICAL VESSEL
Superseded date

01-05-2011

Published date

12-01-2013

Foreword
Introduction
1 Scope
2 Normative references
3 Principle
4 Reagents
5 Apparatus and material
   5.1 Test apparatus: cylindrical vessel
        5.1.1 General
   5.2 Thermostatically controlled liquid bath
        (containing demineralized or distilled water),
        incorporating a stirrer or other rotating device
        for use with one or more pieces of test apparatus.
        It shall be capable of being sealed against loss
        on evaporation and allowing temperatures up to 100
        degree C to be kept constant to 0,1 degree C
   5.3 Thermometer, calibrated and graduated in 0,1
        degree C steps, for use with the thermostatically
        controlled liquid bath
   5.4 Drying oven, capable of maintaining temperatures
        of at least 130 degree C
   5.5 Desiccator, internal diameter of at least 200 mm
   5.6 Polypropylene bottle, of 1000 ml capacity and
        capable of being closed
   5.7 One-mark volumetric flask, 1000 ml capacity
        and conforming to the requirements of class A of
        ISO
   5.8 Funnel, of maximum diameter of 70 mm
   5.9 Balance, accurate to 0,2 x 10[-3] g
   5.10 Cotton wool
6 Test specimens
7 Procedure
8 Expression of results
   8.1 Total loss in mass per unit area
   8.2 Corrosion rate
9 Hot sodium hydroxide test
   9.1 General
   9.2 Test solution, c (NaOH) = 0,1 mol/l
   9.3 Test temperature
   9.4 Duration of the test
   9.5 Test report
10 Other test solution
   10.1 General
   10.2 Test solution
   10.3 Test temperature
   10.4 Duration of the test
   10.5 Test report
Bibliography

Describes a test method for the determination of vitreous and porcelain enamelled articles to resistance to attack by alkaline liquids at temperatures between 25 degrees C and 95 degrees C.

Committee
TC 262
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Superseded
SupersededBy

I.S. EN 15159-2:2006 VITREOUS AND PORCELAIN ENAMELS - GLASS-LINED APPARATUS FOR PROCESS PLANTS - PART 2: DESIGNATION AND SPECIFICATION OF RESISTANCE TO CHEMICAL ATTACK AND THERMAL SHOCK
07/30169151 DC : 0 BS ISO 28765 - VITREOUS AND PORCELAIN ENAMELS - DESIGN OF BOLTED STEEL TANKS FOR THE STORAGE OR TREATMENT OF WATER OR MUNICIPAL OR INDUSTRIAL EFFLUENTS AND SLUDGES
07/30169188 DC : 0 BS ISO 28721-2 - VITREOUS AND PORCELAIN ENAMELS - GLASS-LINED APPARATUS FOR PROCESS PLANTS - PART 2: DESIGNATION AND SPECIFICATION OF RESISTANCE TO CHEMICAL ATTACK AND THERMAL SHOCK
I.S. EN 15711:2009 VITREOUS AND PORCELAIN ENAMELS - GLASS LINED FLANGED STEEL PIPES AND FLANGED STEEL FITTINGS - QUALITY REQUIREMENTS
DIN EN 15711:2009-08 VITREOUS AND PORCELAIN ENAMELS - GLASS LINED FLANGED STEEL PIPES AND FLANGED STEEL FITTINGS - QUALITY REQUIREMENTS
10/30232007 DC : 0 BS EN ISO 28765 - VITREOUS AND PORCELAIN ENAMELS - DESIGN OF BOLTED STEEL TANKS FOR THE STORAGE OR TREATMENT OF WATER OR MUNICIPAL OR INDUSTRIAL EFFLUENTS AND SLUDGES
BS EN 15711:2009 Vitreous and porcelain enamels. Glass lined flanged steel pipes and flanged steel fittings. Quality requirements
09/30197538 DC : 0 BS ISO 12778 - VITREOUS AND PORCELAIN ENAMELS - GLASS LINED FLANGED STEEL PIPES AND FLANGED STEEL FITTINGS - QUALITY REQUIREMENTS
05/30130126 DC : DRAFT FEB 2005 EN 15159-2 - VITREOUS AND PORCELAIN ENAMELS - GLASS-LINED APPARATUS FOR PROCESS PLANTS - PART 2: QUALITY REQUIREMENTS
07/30166946 DC : DRAFT AUG 2007 BS EN 15711 - VITREOUS AND PORCELAIN ENAMELS - GLASS LINED FLANGED STEEL PIPES AND FLANGED STEEL FITTINGS - QUALITY REQUIREMENTS
UNE-EN 15711:2010 Vitreous and porcelain enamels - Glass lined flanged steel pipes and flanged steel fittings - Quality requirements
UNI EN 15711 : 2009 VITREOUS AND PORCELAIN ENAMELS - GLASS LINED FLANGED STEEL PIPES AND FLANGED STEEL FITTINGS - QUALITY REQUIREMENTS
I.S. EN 15282:2007 VITREOUS AND PORCELAIN ENAMELS - DESIGN OF BOLTED STEEL TANKS FOR THE STORAGE OR TREATMENT OF WATER OR MUNICIPAL OR INDUSTRIAL EFFLUENTS AND SLUDGES
BS EN 15159-2:2006 Vitreous and porcelain enamels. Glass-lined apparatus for process plants Designation and specification of resistance to chemical attack and thermal shock
BS EN 15282:2007 Vitreous and porcelain enamels. Design of bolted steel tanks for the storage or treatment of water or municipal or industrial effluents and sludges
EN 15159-2:2006 Vitreous and porcelain enamels - Glass-lined apparatus for process plants - Part 2: Designation and specification of resistance to chemical attack and thermal shock
EN 15282:2007 Vitreous and porcelain enamels - Design of bolted steel tanks for the storage or treatment of water or municipal or industrial effluents and sludges
EN 15711:2009 Vitreous and porcelain enamels - Glass lined flanged steel pipes and flanged steel fittings - Quality requirements
DIN EN 15711 E : 2009 VITREOUS AND PORCELAIN ENAMELS - GLASS LINED FLANGED STEEL PIPES AND FLANGED STEEL FITTINGS - QUALITY REQUIREMENTS
DIN EN 15282:2007-06 VITREOUS AND PORCELAIN ENAMELS - DESIGN OF BOLTED STEEL TANKS FOR THE STORAGE OR TREATMENT OF WATER OR MUNICIPAL OR INDUSTRIAL EFFLUENTS AND SLUDGES

ISO 2723:1995 Vitreous and porcelain enamels for sheet steel Production of specimens for testing
ISO 1042:1998 Laboratory glassware One-mark volumetric flasks
ISO 2724:1973 Vitreous and porcelain enamels for cast iron Production of specimens for testing
EN ISO 3696:1995 Water for analytical laboratory use - Specification and test methods (ISO 3696:1987)
ISO 48:2010 Rubber, vulcanized or thermoplastic Determination of hardness (hardness between 10 IRHD and 100 IRHD)
ISO 13804:1999 Vitreous and porcelain enamels for aluminium Production of specimens for testing
ISO 868:2003 Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness)
EN 10088-1:2014 Stainless steels - Part 1: List of stainless steels

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more