Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

EN 60794-2-50 : 2008

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

OPTICAL FIBRE CABLES - PART 2-50: INDOOR CABLES - FAMILY SPECIFICATION FOR SIMPLEX AND DUPLEX CABLES FOR USE IN TERMINATED CABLE ASSEMBLIES
Superseded date

17-03-2020

Published date

12-01-2013

FOREWORD
1 Scope
2 Normative references
3 Terms and definitions
4 Construction
  4.1 General
  4.2 Optical fibres and primary coating
  4.3 Buffer
  4.4 Tube
  4.5 Strength and anti-buckling members
  4.6 Sheath
  4.7 Sheath marking
  4.8 Examples of cable constructions
5 Tests
  5.1 Dimensions
  5.2 Mechanical requirements
      5.2.1 Tensile performance
      5.2.2 Crush
      5.2.3 Impact
      5.2.4 Repeated bending
      5.2.5 Bend
      5.2.6 Torsion
      5.2.7 Bend at low temperature
      5.2.8 Kink
      5.2.9 Sheath pull-off force
      5.2.10 Buffered fibre movement in compression
  5.3 Environmental requirements
      5.3.1 Temperature cycling
      5.3.2 Sheath shrinkage
  5.4 Transmission requirements
  5.5 Fire performance
Annex A (normative) - Examples of some types of cable
        construction
Annex B (normative) - METHOD E21 - Sheath pull-off force
        for optical fibre cable for use in patch cords
Annex C (normative) - METHOD F11 - Sheath shrinkage for
        optical fibre cable for use in patchcords
Annex D (normative) - METHOD E22 - Buffered fibre movement
        under compression in optical fibre cables for use
        in patchcords
Annex E (normative) - METHOD F12 - Temperature cycling for
        optical fibre cable for use in patchcords
Annex F (normative) - Guidance on the selection of tests applicable
        to optical fibre cables for use in patchcords
Annex ZA (normative) - Normative references to international
         publications with their corresponding European publications
Bibliography

Defines requirements for simplex and duplex optical fibre cables for use in terminated cable assemblies or for termination with optical fibre passive components.

Committee
TC 86A
DevelopmentNote
To be read in conjunction with EN 60794-1-1, EN 60794-1-2 and EN 60794-2. (08/2008)
DocumentType
Standard
PublisherName
European Committee for Standards - Electrical
Status
Superseded
SupersededBy

CEI EN 50377-8-13 : 2012 CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 8-13: TYPE LSH-PC SIMPLEX TERMINATED ON IEC 60793-2-50 CATEGORY B1.1 AND B1.3 SINGLEMODE FIBRE WITH TITANIUM COMPOSITE FERRULE FOR CATEGORY U
BS EN 50411-3-8:2016 Fibre organizers and closures to be used in optical fibre communication systems. Product specifications Fibre management system, terminal equipment box type 1 for category C
I.S. EN 61753-053-2:2014 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS - PERFORMANCE STANDARD - PART 053-2: NON-CONNECTORIZED SINGLE-MODE FIBRE, ELECTRICALLY CONTROLLED, VARIABLE OPTICAL ATTENUATOR FOR CATEGORY C - CONTROLLED ENVIRONMENTS
BS EN 61753-053-2:2014 Fibre optic interconnecting devices and passive components. Performance standard Non-connectorized single-mode fibre, electrically controlled, variable optical attenuator for category C. Controlled environments
BS EN 60794-2-51:2014 Optical fibre cables Indoor cables. Detail specification for simplex and duplex cables for use in cords for controlled environment
BS EN 50377-16-1:2011 Connector sets and interconnect components to be used in optical fibre communication systems. Product specifications Type LF3 APC simplex terminated on IEC 60793-2-50 category B1.1 and B1.3 singlemode fibre with titanium composite ferrule for category C
09/30215019 DC : 0 BS EN 50551-1 - SIMPLEX AND DUPLEX CABLES TO BE USED FOR CORDS - PART 1: BLANK DETAIL SPECIFICATION AND MINIMUM REQUIREMENTS
UNE-EN 50377-4-2:2015 Connector sets and interconnect components to be used in optical fibre communication systems - Product specifications - Part 4-2: Type SC/APC simplex 8° terminated on IEC 60793-2-50 of types B1.1 and B1.3 singlemode fibre, with full zirconia ferrule category U
CEI EN 50377-14-1 : 2012 CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 14-1: CORDS WITH IEC 60793-2-50 SINGLEMODE CATEGORY B1.1 AND B1.3 FIBRE FOR CATEGORY C
17/30347862 DC : 0 BS EN 50377-14-1 - CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 14-1: SIMPLEX AND DUPLEX CORDS MADE FROM SIMPLEX PLUGS WITH CYLINDRICAL FERRULES, USING EN 60793-2-50 SINGLEMODE B1 OR B6 FIBRE FOR CATEGORY C ACCORDING TO EN 61753-1
BS EN 61753-061-2:2012 Fibre optic interconnecting devices and passive components. Performance standard Non-connectorized single-mode fibre optic pigtailed isolators for category C. Controlled environment
PREN 50411-3-8 : DRAFT 2014 FIBRE ORGANIZERS AND CLOSURES TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 3-8: FIBRE MANAGEMENT SYSTEM, TERMINAL EQUIPMENT BOX TYPE 1 FOR CATEGORY C
08/30195624 DC : 0 BS EN 50377-8-11 - CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 8-11: TYPE LSH-PC SIMPLEX TERMINATED ON IEC 60793-2-50 CATEGORY B1.1 AND B1.3 SINGLE MODE FIBRE WITH TITANIUM COMPOSITE FERRULE FOR CATEGORY C
CEI EN 61754-34 : 1ED 2017 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS - FIBRE OPTIC CONNECTOR INTERFACES - PART 34: TYPE URM CONNECTOR FAMILY
CEI EN 50377-13-3 : 2012 CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 13-3: TYPE LX.5-APC DUPLEX TERMINATED ON IEC 60793-2-50 CATEGORY B1.1 AND B1.3 SINGLEMODE FIBRE, WITH FULL ZIRCONIA FERRULE CATEGORY U
I.S. EN 61753-052-6:2016 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS - PERFORMANCE STANDARD - PART 052-6: SINGLE-MODE FIBRE NON-CONNECTORIZED FIXED ATTENUATOR - CATEGORY O IN OUTSIDE PLANT ENVIRONMENT
I.S. EN 61754-28:2012 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS - FIBRE OPTIC CONNECTOR INTERFACES - PART 28: TYPE LF3 CONNECTOR FAMILY (IEC 61754-28:2012 (EQV))
BS EN 50551-1:2011 Simplex and duplex cables to be used for cords Blank detail specification and minimum requirements
I.S. EN 61753-091-2:2013 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS - PERFORMANCE STANDARD - PART 091-2: NON-CONNECTORIZED SINGLE-MODE FIBRE OPTIC PIGTAILED CIRCULATORS FOR CATEGORY C - CONTROLLED ENVIRONMENT (IEC 61753-091-2:2012 (EQV))
I.S. EN 50377-4-2:2011 CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 4-2: TYPE SC/APC SIMPLEX 8 DEGREES TERMINATED ON IEC 60793-2-50 OF TYPES B1.1 AND B1.3 SINGLEMODE FIBRE, WITH FULL ZIRCONIA FERRULE CATEGORY U
NF EN 50551-1 : 2011 SIMPLEX AND DUPLEX CABLES TO BE USED FOR CORDS - PART 1: BLANK DETAIL SPECIFICATION AND MINIMUM REQUIREMENTS
I.S. EN 50551-1:2011 SIMPLEX AND DUPLEX CABLES TO BE USED FOR CORDS - PART 1: BLANK DETAIL SPECIFICATION AND MINIMUM REQUIREMENTS
EN 50377-13-2:2011 Connector sets and interconnect components to be used in optical fibre communication systems - Product specifications - Part 13-2: Type LX.5-PC DUPLEX terminated on IEC 60793-2-50 category B1.1 and B1.3 singlemode fibre, with full zirconia ferrule category U
EN 50411-3-5:2015 Fibre organisers and closures to be used in optical fibre communication systems - Product specifications - Part 3-5: Wall outlet
EN 50377-17-2:2015 Connector sets and Interconnect components to be used in optical fibre communication systems - Product specifications - Part 17-2: Type FPFT (factory polished field terminated) simplex connector factory terminated with EN 60793-2-50 category B1.3 fibre and field mounted onto reinforced cable containing IEC 60793-2-50 category B1.3 or B6a1 or B6a 2 singlemode fibre (with restricted MFD), category C
EN 61753-052-6:2016 Fibre optic interconnecting devices and passive components - Performance standard - Part 052-6: Single-mode fibre non-connectorized fixed attenuator - Category O in outside plant environment
EN 50377-2-2 : 2009 Connector sets and interconnect components to be used in optical fibre communication systems - Product specifications - Part 2-2: FC/APC 8 terminated on IEC 60793-2-50 category B1.1 and B1.3 singlemode fibre, with full zirconia ferrule, category C
EN 50377-4-2:2011 Connector sets and interconnect components to be used in optical fibre communication systems - Product specifications - Part 4-2: Type SC/APC simplex 8° terminated on IEC 60793-2-50 of types B1.1 and B1.3 singlemode fibre, with full zirconia ferrule category U
EN 50377-8-10:2010 Connector sets and interconnect components to be used in optical fibre communication systems - Product specifications - Part 8-10: Type LSH-APC simplex terminated on IEC 60793-2-50 category B1.1 and B1.3 singlemode fibre with titanium composite ferrule for category C
EN 61754-32:2016 Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 32: Type DiaLink connector family
EN 61754-29 : 2012 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS - FIBRE OPTIC CONNECTOR INTERFACES - PART 29: TYPE BLINK CONNECTOR SERIES (IEC 61754-29:2012)
EN 50411-3-8:2016 Fibre organizers and closures to be used in optical fibre communication systems - Product specifications - Part 3-8: Fibre management system, terminal equipment box type 1 for category C
EN 50516-2-1 : 2011 INDUSTRIAL CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE CONTROL AND COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 2-1: TYPE ODVA PC INDUSTRIAL TERMINATED ON EN 60793-2-10 CATEGORY A1A AND A1B MULTIMODE FIBRE TO MEET THE REQUIREMENTS OF CATEGORY 1 (INDUSTRIAL ENVIRONMENTS) AS SPECIFIED IN EN 50173-1 AND IEC 61753-1-3
EN 61753-121-2:2017 Fibre optic interconnecting devices and passive components - Performance standard - Part 121-2: Simplex and duplex cords with single-mode fibre and cylindrical ferrule connectors for category C - Controlled environment
EN 50411-3-6:2013 Fibre organisers and closures to be used in optical fibre communication systems - Product specifications - Part 3-6: Multimode mechanical fibre splice for use in an outdoor protected environment (Cat U)
EN 61753-091-2:2013 Fibre optic interconnecting devices and passive components - Performance standard - Part 091-2: Non-connectorized single-mode fibre optic pigtailed circulators for category C - Controlled environment
EN 50377-13-3:2011 Connector sets and interconnect components to be used in optical fibre communication systems - Product specifications - Part 13-3: Type LX.5-APC DUPLEX terminated on IEC 60793-2-50 category B1.1 and B1.3 singlemode fibre, with full zirconia ferrule category U
EN 61753-052-3:2016 Fibre optic interconnecting devices and passive components - Performance standard - Part 052-3: Single-mode fibre non-connectorized fixed attenuator - Category U in uncontrolled environment
EN 60794-2-22:2017 Optical fibre cables - Part 2-22: Indoor cables - Detail specification for multi-simplex breakout optical cables to be terminated with connectors
EN 50411-3-2:2011 Fibre organisers and closures to be used in optical fibre communication systems - Product specifications - Part 3-2: Singlemode mechanical fibre splice
EN 61754-30:2014 Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 30: Type CLIK connector series
BS EN 50377-7-4:2011 Connector sets and interconnect components to be used in optical fibre communication systems. Product specifications LC-PC simplex terminated on IEC 60793-2-50 category B1.1 and B1.3 singlemode fibre with full zirconia ferrule for category C
08/30190093 DC : DRAFT SEP 2008 BS EN 50377-7-4 - CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 7-4: LC-PC SIMPLEX TERMINATED ON IEC 60793-2-50 CATEGORY B1.1 AND B1.3 SINGLE MODE FIBRE WITH FULL ZIRCONIA FERRULE FOR CATEGORY C
BS EN 61754-28:2012 Fibre optic interconnecting devices and passive components. Fibre optic connector interfaces Type LF3 connector family
BS EN 50377-17-1:2013 Connector sets and interconnect components to be used in optical fibre communication systems. Product specifications Type FPFT (factory polished field terminated) simplex connector factory terminated with EN 60793-2-50 category B1.3 fibre and field mounted onto IEC 60793-2-50 category B1.3 or B6a_1 or B6a_2 singlemode fibre, category C
I.S. EN 50411-3-2:2011 FIBRE ORGANISERS AND CLOSURES TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 3-2: SINGLEMODE MECHANICAL FIBRE SPLICE
BS EN 60794-2-22:2017 Optical fibre cables Indoor cables. Detail specification for multi-simplex breakout optical cables to be terminated with connectors
BS EN 61753-052-6:2016 Fibre optic interconnecting devices and passive components. Performance standard Single-mode fibre non-connectorized fixed attenuator. Category O in outside plant environment
BS EN 50377-8-12:2010 Connector sets and interconnect components to be used in optical fibre communication systems. Product specifications Type LSH-APC simplex terminated on IEC 60793-2-50 category B1.1 and B1.3 singlemode fibre with titanium composite ferrule for category U
I.S. EN 50411-3-6:2013 FIBRE ORGANISERS AND CLOSURES TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 3-6: MULTIMODE MECHANICAL FIBRE SPLICE FOR USE IN AN OUTDOOR PROTECTED ENVIRONMENT (CAT U)
BS EN 50411-3-2:2011 Fibre organisers and closures to be used in optical fibre communication systems. Product specifications Singlemode mechanical fibre splice
14/30262209 DC : 0 BS EN 50411-3-8 - FIBRE ORGANIZERS AND CLOSURES TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 3-8: FIBRE MANAGEMENT SYSTEM, TERMINAL EQUIPMENT BOX TYPE 1 FOR CATEGORY C
BS EN 61754-29:2012 Fibre optic interconnecting devices and passive components. Fibre optic connector interfaces Type BLINK connector series
BS EN 61753-121-2:2017 Fibre optic interconnecting devices and passive components. Performance standard Simplex and duplex cords with single-mode fibre and cylindrical ferrule connectors for category C. Controlled environment
BS EN 50377-4-4:2011 Connector sets and interconnect components to be used in optical fibre communication systems. Product specifications Type SC-PC simplex terminated on IEC 60793-2-50 category B1.1 and B1.3 singlemode fibre, with full zirconia ferrule category U
BS EN 50377-4-2:2011 Connector sets and interconnect components to be used in optical fibre communication systems. Product specifications Type SC/APC simplex 8° terminated on IEC 60793-2-50 of types B1.1 and B1.3 singlemode fibre, with full zirconia ferrule category U
BS EN 50377-14-1:2011 Connector sets and interconnect components to be used in optical fibre communication systems. Product specifications Cords with IEC 60793-2-50 singlemode category B1.1 and B1.3 fibre for category C
CEI EN 50551-2 : 2014 SIMPLEX AND DUPLEX CABLES TO BE USED FOR CORDS - PART 2: DETAILED SPECIFICATION AND MINIMUM REQUIREMENTS FOR A 3,0 MM SIMPLEX RUGGEDISED SINGLE MODE FIBRE CABLE TO BE USED FOR PATCHCORDS/CORDS CATEGORY U
I.S. EN 61754-30:2014 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS - FIBRE OPTIC CONNECTOR INTERFACES - PART 30: TYPE CLIK CONNECTOR SERIES
CEI EN 61753-091-2 : 2013 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS - PERFORMANCE STANDARD - PART 091-2: NON-CONNECTORISED SINGLE-MODE FIBRE OPTIC PIGTAILED CIRCULATORS FOR CATEGORY C - CONTROLLED ENVIRONMENT
CEI EN 50377-2-2 : 2010 CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 2-2: FC/APC 8 TERMINATED ON IEC 60793-2-50 CATEGORY B1.1 AND B1.3 SINGLEMODE FIBRE, WITH FULL ZIRCONIA FERRULE, CATEGORY C
I.S. EN 50411-3-5:2015 FIBRE ORGANISERS AND CLOSURES TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 3-5: WALL OUTLET
I.S. EN 50377-8-12:2010 CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 8-12: TYPE LSH-APC SIMPLEX TERMINATED ON IEC 60793-2-50 CATEGORY B1.1 AND B1.3 SINGLEMODE FIBRE WITH TITANIUM COMPOSITE FERRULE FOR CATEGORY U
I.S. EN 50377-14-1:2011 CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 14-1: CORDS WITH IEC 60793-2-50 SINGLEMODE CATEGORY B1.1 AND B1.3 FIBRE FOR CATEGORY C
CEI EN 61753-121-3 : 2012 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS - PERFORMANCE STANDARDS - PART 121-3: SIMPLEX AND DUPLEX CORDS WITH SINGLEMODE FIBRE AND CYLINDRICAL FERRULE CONNECTORS FOR CATEGORY U - UNCONTROLLED ENVIRONMENT
08/30195630 DC : 0 BS EN 50377-8-13 - CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 8-13: TYPE LSH-PC SIMPLEX TERMINATED ON IEC 60793-2-50 CATEGORY B1.1 AND B1.3 SINGLE MODE FIBRE WITH TITANIUM COMPOSITE FERRULE FOR CATEGORY U
BS EN 50516-2-1:2011 Industrial connector sets and interconnect components to be used in optical fibre control and communication systems. Product specifications Type ODVA PC industrial terminated on EN 60793-2-10 category A1a and A1b multimode fibre to meet the requirements of category I (industrial environments) as specified in EN 50173-1 and IEC 61753-1-3
I.S. EN 50377-2-2:2009 CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 2-2: FC/APC 8 TERMINATED ON IEC 60793-2-50 CATEGORY B1.1 AND B1.3 SINGLEMODE FIBRE, WITH FULL ZIRCONIA FERRULE, CATEGORY C
NF EN 50377-8-12 : 2011 CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 8-12: TYPE LSH-APC SIMPLEX TERMINATED ON IEC 60793-2-50 CATEGORY B1.1 AND B1.3 SINGLEMODE FIBRE WITH TITANIUM COMPOSITE FERRULE FOR CATEGORY U
CEI EN 50516-1-1 : 2012 INDUSTRIAL CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE CONTROL AND COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 1-1: TYPE SC-RJ PC INDUSTRIAL TERMINATED ON EN 60793-2-10 CATEGORY A1A AND A1B MULTIMODE FIBRE TO MEET THE REQUIREMENTS OF CATEGORY I (INDUSTRIAL ENVIRONMENTS) AS SPECIFIED IN IEC 61753-1-3
TS 102 873 : 1.1.1 ACCESS, TERMINALS, TRANSMISSION AND MULTIPLEXING (ATTM); OPTICAL EXTERNAL NETWORK TESTING INTERFACE
CEI EN 50377-16-1 : 2012 CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 16-1: TYPE LF3 APC SIMPLEX TERMINATED ON IEC 60793-2-50 CATEGORY B1.1 AND B1.3 SINGLE MODE FIBRE WITH TITANIUM COMPOSITE FERRULE FOR CATEGORY C
BS EN 61753-081-2:2014 Fibre optic interconnecting devices and passive components. Performance standard Non-connectorized single-mode fibre optic middle-scale 1 x N DWDM devices for category C. Controlled environments
BS EN 50377-13-3:2011 Connector sets and interconnect components to be used in optical fibre communication systems. Product specifications Type LX.5-APC DUPLEX terminated on IEC 60793-2-50 category B1.1 and B1.3 singlemode fibre, with full zirconia ferrule category U
08/30195627 DC : 0 BS EN 50377-8-12 - CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 8-12: TYPE LSH-APC SIMPLEX TERMINATED ON IEC 60793-2-50 CATEGORY B1.1 AND B1.3 SINGLE MODE FIBRE WITH TITANIUM COMPOSITE FERRULE FOR CATEGORY U
14/30285749 DC : 0 BS EN 50377-17-2 - CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 17-2: TYPE FPFT (FACTORY POLISHED FIELD TERMINATED) SIMPLEX CONNECTOR FACTORY TERMINATED WITH EN 60793-2-50 CATEGORY B1.3 FIBRE AND FIELD MOUNTED ONTO TIGHT JACKET CABLE CONTAINING IEC 60793-2-50 CATEGORY B1.3 OR B6A1 OR B6A 2 SIN
CEI EN 50551-1 : 2012 SIMPLEX AND DUPLEX CABLES TO BE USED FOR CORDS - PART 1: BLANK DETAIL SPECIFICATION AND MINIMUM REQUIREMENTS
BS EN 50377-8-11:2010 Connector sets and interconnect components to be used in optical fibre communication systems. Product specifications Type LSH-PC simplex terminated on IEC 60793-2-50 category B1.1 and B1.3 singlemode fibre with titanium composite ferrule for category C
13/30271356 DC : 0 BS EN 50411-3-5 - FIBRE ORGANISERS AND CLOSURES TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 3-5 WALL OUTLET
BS EN 61754-30:2014 Fibre optic interconnecting devices and passive components. Fibre optic connector interfaces Type CLIK connector series
BS EN 50516-3-1:2014 Industrial connector sets and interconnect components to be used in optical fibre control and communication systems. Product specifications Type ODVA APC terminated on EN 60793-2-50 category B1.1 and B1.3 singlemode fibre to meet the requirements of category I (industrial environments) as specified in EN 50173-1 and IEC 61753-1-3
CEI EN 61753-052-6 : 1ED 2017 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS - PERFORMANCE STANDARD - PART 052-6: SINGLE-MODE FIBRE NONCONNECTORIZED FIXED ATTENUATOR - CATEGORY O IN OUTSIDE PLANT ENVIRONMENT
BS EN 61753-052-3:2016 Fibre optic interconnecting devices and passive components. Performance standard Single-mode fibre non-connectorized fixed attenuator. Category U in uncontrolled environment
CEI EN 61754-29 : 2013 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS - FIBRE OPTIC CONNECTOR INTERFACES - PART 29: TYPE BLINK CONNECTOR SERIES
CEI EN 50377-8-11 : 2012 CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 8-11: TYPE LSH-PC SIMPLEX TERMINATED ON IEC 60793-2-50 CATEGORY B1.1 AND B1.3 SINGLEMODE FIBRE WITH TITANIUM COMPOSITE FERRULE FOR CATEGORY C
12/30262212 DC : 0 BS EN 50516-3-1 - INDUSTRIAL CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE CONTROL AND COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 3-1: TYPE ODVA APC TERMINATED ON EN 60793-2-50 CATEGORY B1.1 AND B1.3 SINGLEMODE FIBRE TO MEET THE REQUIREMENTS OF CATEGORY 1 (INDUSTRIAL ENVIRONMENTS) AS SPECIFIED IN EN 50173-1 AND IEC 61753-1-3
BS EN 50377-13-2:2011 Connector sets and interconnect components to be used in optical fibre communication systems. Product specifications Type LX.5-PC DUPLEX terminated on IEC 60793-2-50 category B1.1 and B1.3 singlemode fibre, with full zirconia ferrule category U
BS EN 61754-32:2016 Fibre optic interconnecting devices and passive components. Fibre optic connector interfaces Type DiaLink connector family
CEI EN 61753-052-3 : 2004 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS - PERFORMANCE STANDARD - PART 052-3: SINGLE-MODE FIBRE NONCONNECTORIZED FIXED ATTENUATOR - CATEGORY U IN UNCONTROLLED ENVIRONMENT
I.S. EN 61754-34:2016 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS - FIBRE OPTIC CONNECTOR INTERFACES - PART 34: TYPE URM CONNECTOR FAMILY
08/30193101 DC : 0 BS EN 50377-4-2 - CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 4-2: TYPE SC/APC SIMPLEX 8 DEGREE TERMINATED ON IEC 60793-2-50 CATEGORY B1.1 AND B1.3 SINGLEMODE FIBRE, WITH FULL ZIRCONIA FERRULE CATEGORY U
CEI EN 50377-13-2 : 2012 CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 13-2: TYPE LX.5-PC DUPLEX TERMINATED ON IEC 60793-2-50 CATEGORY B1.1 AND B1.3 SINGLEMODE FIBRE, WITH FULL ZIRCONIA FERRULE CATEGORY U
CEI EN 50377-8-12 : 2012 CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 8-12: TYPE LSH-APC SIMPLEX TERMINATED ON IEC 60793-2-50 CATEGORY B1.1 AND B1.3 SINGLEMODE FIBRE WITH TITANIUM COMPOSITE FERRULE FOR CATEGORY U
I.S. EN 50551-2:2013 SIMPLEX AND DUPLEX CABLES TO BE USED FOR CORDS - PART 2: DETAILED SPECIFICATION AND MINIMUM REQUIREMENTS FOR A 3,0 MM SIMPLEX RUGGEDISED SINGLE MODE FIBRE CABLE TO BE USED FOR PATCHCORDS/CORDS CATEGORY U
CEI EN 50516-2-1 : 2012 INDUSTRIAL CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE CONTROL AND COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 2-1: TYPE ODVA PC INDUSTRIAL TERMINATED ON EN 60793-2-10 CATEGORY A1A AND A1B MULTIMODE FIBRE TO MEET THE REQUIREMENTS OF CATEGORY 1 (INDUSTRIAL ENVIRONMENTS) AS SPECIFIED IN EN 50173-1 AND IEC 61753-1-3
I.S. EN 61753-081-2:2014 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS - PERFORMANCE STANDARD - PART 081-2: NON-CONNECTORIZED SINGLE-MODE FIBRE OPTIC MIDDLE-SCALE 1 X N DWDM DEVICES FOR CATEGORY C - CONTROLLED ENVIRONMENTS
EN 61753-061-2:2012 Fibre optic interconnecting devices and passive components - Performance standard - Part 061-2: Non-connectorized single-mode fibre optic pigtailed isolators for category C - Controlled environment
EN 61754-34:2016 Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 34: Type URM connector family
CEI EN 61754-30 : 2014 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS - FIBRE OPTIC CONNECTOR INTERFACES - PART 30: TYPE CLIK CONNECTOR SERIES
I.S. EN 61753-052-3:2016 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS - PERFORMANCE STANDARD - PART 052-3: SINGLE-MODE FIBRE NONCONNECTORIZED FIXED ATTENUATOR - CATEGORY U IN UNCONTROLLED ENVIRONMENT
I.S. EN 50377-7-4:2011 CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 7-4: LC-PC SIMPLEX TERMINATED ON IEC 60793-2-50 CATEGORY B1.1 AND B1.3 SINGLEMODE FIBRE WITH FULL ZIRCONIA FERRULE FOR CATEGORY C
I.S. EN 50377-8-11:2010 CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 8-11: TYPE LSH-PC SIMPLEX TERMINATED ON IEC 60793-2-50 CATEGORY B1.1 AND B1.3 SINGLEMODE FIBRE WITH TITANIUM COMPOSITE FERRULE FOR CATEGORY C
08/30189758 DC : DRAFT SEP 2008 BS EN 50377-13-3 - CONNECTORS SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 13-3: TYPE LX.5-APC DUPLEX TERMINATED ON EN 60793-2-50 CATEGORY B1.1 AND B1.3 SINGLEMODE FIBRE, WITH FULL ZIRCONIA FERRULE CATEGORY U
BS EN 50377-17-2:2015 Connector sets and Interconnect components to be used in optical fibre communication systems. Product specifications Type FPFT (factory polished field terminated) simplex connector factory terminated with EN 60793-2-50 category B1.3 fibre and field mounted onto reinforced cable containing IEC 60793-2-50 category B1.3 or B6a1 or B6a 2 singlemode fibre (with restricted MFD), category C
BS EN 50377-8-10:2010 Connector sets and interconnect components to be used in optical fibre communication systems. Product specifications Type LSH-APC simplex terminated on IEC 60793-2-50 category B1.1 and B1.3 singlemode fibre with titanium composite ferrule for category C
CEI EN 50377-8-10 : 2012 CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 8-10: TYPE LSH-APC SIMPLEX TERMINATED ON IEC 60793-2-50 CATEGORY B1.1 AND B1.3 SINGLEMODE FIBRE WITH TITANIUM COMPOSITE FERRULE FOR CATEGORY C
BS EN 61754-34:2016 Fibre optic interconnecting devices and passive components. Fibre optic connector interfaces Type URM connector family
CEI EN 61753-121-2 : 2012 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS - PERFORMANCE STANDARDS - PART 121-2: SIMPLEX AND DUPLEX CORDS WITH SINGLEMODE FIBRE AND CYLINDRICAL FERRULE CONNECTORS FOR CATEGORY C - CONTROLLED ENVIRONMENT
CEI EN 60794-2-22 : 1ED 2017 OPTICAL FIBRE CABLES - PART 2-22: INDOOR CABLES - DETAIL SPECIFICATION FOR MULTI-SIMPLEX BREAKOUT OPTICAL CABLES TO BE TERMINATED WITH CONNECTORS
I.S. EN 50377-16-1:2011 CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 16-1: TYPE LF3 APC SIMPLEX TERMINATED ON IEC 60793-2-50 CATEGORY B1.1 AND B1.3 SINGLEMODE FIBRE WITH TITANIUM COMPOSITE FERRULE FOR CATEGORY C
I.S. EN 61753-121-3:2010 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS - PERFORMANCE STANDARD - PART 121-3: SIMPLEX AND DUPLEX CORDS WITH SINGLE-MODE FIBRE AND CYLINDRICAL FERRULE CONNECTORS FOR CATEGORY U - UNCONTROLLED ENVIRONMENT
PREN 50377-14-1 : DRAFT 2017 CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 14-1: SIMPLEX AND DUPLEX CORDS MADE FROM SIMPLEX PLUGS WITH CYLINDRICAL FERRULES, USING EN 60793-2-50 SINGLEMODE B1 OR B6 FIBRE FOR CATEGORY C ACCORDING TO EN 61753-1
CEI EN 61753-061-2 : 2013 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS - PERFORMANCE STANDARD - PART 061-2: NON-CONNECTORIZED SINGLE-MODE FIBRE OPTIC PIGTAILED ISOLATORS FOR CATEGORY C - CONTROLLED ENVIRONMENT
08/30189753 DC : DRAFT SEP 2008 BS EN 50377-13-2 - CONNECTORS SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 13-2: TYPE LX.5-PC DUPLEX TERMINATED ON EN 60793-2-50 CATEGORY B1.1 AND B1.3 SINGLEMODE FIBRE, WITH FULL ZIRCONIA FERRULE CATEGORY U
08/30193326 DC : DRAFT NOV 2008 BS EN 50377-14-1 - CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 14-1: PATCH CORDS WITH EN 60793-2-50 SINGLE MODE CATEGORY B1.1 AND B1.3 FIBRE FOR CATEGORY C
CEI EN 50377-4-2 : 2012 CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 4-2: TYPE SC/APC SIMPLEX 8 DEGREES TERMINATED ON IEC 60793-2-50 OF TYPES B1.1 AND B1.3 SINGLEMODE FIBRE, WITH FULL ZIRCONIA FERRULE CATEGORY U
CEI EN 50516-3-1 : 2014 INDUSTRIAL CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE CONTROL AND COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 3-1: TYPE ODVA APC TERMINATED ON EN 60793-2-50 CATEGORY B1.1 AND B1.3 SINGLEMODE FIBRE TO MEET THE REQUIREMENTS OF CATEGORY 1 (INDUSTRIAL ENVIRONMENTS) AS SPECIFIED IN EN 50173-1 AND IEC 61753-1-3
I.S. EN 50411-3-8:2016 FIBRE ORGANIZERS AND CLOSURES TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 3-8: FIBRE MANAGEMENT SYSTEM, TERMINAL EQUIPMENT BOX TYPE 1 FOR CATEGORY C
I.S. EN 50516-2-1:2011 INDUSTRIAL CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE CONTROL AND COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 2-1: TYPE ODVA PC INDUSTRIAL TERMINATED ON EN 60793-2-10 CATEGORY A1A AND A1B MULTIMODE FIBRE TO MEET THE REQUIREMENTS OF CATEGORY I (INDUSTRIAL ENVIRONMENTS) AS SPECIFIED IN EN 50173-1 AND IEC 61753-1-3
I.S. EN 50377-13-2:2011 CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 13-2: TYPE LX.5-PC DUPLEX TERMINATED ON IEC 60793-2-50 CATEGORY B1.1 AND B1.3 SINGLEMODE FIBRE, WITH FULL ZIRCONIA FERRULE CATEGORY U
I.S. EN 50377-13-3:2011 CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 13-3: TYPE LX.5-APC DUPLEX TERMINATED ON IEC 60793-2-50 CATEGORY B1.1 AND B1.3 SINGLEMODE FIBRE, WITH FULL ZIRCONIA FERRULE CATEGORY U
I.S. EN 50516-3-1:2014 INDUSTRIAL CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE CONTROL AND COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 3-1: TYPE ODVA APC TERMINATED ON EN 60793-2-50 CATEGORY B1.1 AND B1.3 SINGLEMODE FIBRE TO MEET THE REQUIREMENTS OF CATEGORY 1 (INDUSTRIAL ENVIRONMENTS) AS SPECIFIED IN EN 50173-1 AND IEC 61753-1-3
I.S. EN 60794-2-22:2017 OPTICAL FIBRE CABLES - PART 2-22: INDOOR CABLES - DETAIL SPECIFICATION FOR MULTI-SIMPLEX BREAKOUT OPTICAL CABLES TO BE TERMINATED WITH CONNECTORS
I.S. EN 50377-17-2:2015 CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 17-2: TYPE FPFT (FACTORY POLISHED FIELD TERMINATED) SIMPLEX CONNECTOR FACTORY TERMINATED WITH EN 60793-2-50 CATEGORY B1.3 FIBRE AND FIELD MOUNTED ONTO REINFORCED CABLE CONTAINING IEC 60793-2-50 CATEGORY B1.3 OR B6A1 OR B6A2 SINGLEMODE FIBRE
CEI EN 50411-3-2 : 2012 FIBRE ORGANISERS AND CLOSURES TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 3-2: SINGLEMODE MECHANICAL FIBRE SPLICE
CEI EN 50377-4-4 : 2012 CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 4-4: TYPE SC-PC SIMPLEX TERMINATED ON IEC 60793-2-50 CATEGORY B1.1 AND B1.3 SINGLEMODE FIBRE, WITH FULL ZIRCONIA FERRULE CATEGORY U
I.S. EN 50516-1-1:2011 INDUSTRIAL CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE CONTROL AND COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 1-1: TYPE SC-RJ PC INDUSTRIAL TERMINATED ON EN 60793-2-10 CATEGORY A1A AND A1B MULTIMODE FIBRE TO MEET THE REQUIREMENTS OF CATEGORY I (INDUSTRIAL ENVIRONMENTS) AS SPECIFIED IN IEC 61753-1-3
I.S. EN 61753-121-2:2017 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS - PERFORMANCE STANDARDS - PART 121-2: SIMPLEX AND DUPLEX CORDS WITH SINGLE-MODE FIBRE AND CYLINDRICAL FERRULE CONNECTORS FOR CATEGORY C - CONTROLLED ENVIRONMENT
EN 50377-8-12:2010 Connector sets and interconnect components to be used in optical fibre communication systems - Product specifications - Part 8-12: Type LSH-APC simplex terminated on IEC 60793-2-50 category B1.1 and B1.3 singlemode fibre with titanium composite ferrule for category U
I.S. EN 50377-8-10:2010 CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 8-10: TYPE LSH-APC SIMPLEX TERMINATED ON IEC 60793-2-50 CATEGORY B1.1 AND B1.3 SINGLEMODE FIBRE WITH TITANIUM COMPOSITE FERRULE FOR CATEGORY C
BS EN 50377-8-13:2010 Connector sets and interconnect components to be used in optical fibre communication systems. Product specifications Type LSH-PC simplex terminated on IEC 60793-2-50 category B1.1 and B1.3 singlemode fibre with titanium composite ferrule for category U
BS EN 50551-2:2013 Simplex and duplex cables to be used for cords Detailed specification and minimum requirements for a 3,0 mm simplex ruggedised single mode fibre cable to be used for patchcords/cords category U
I.S. EN 50377-8-13:2010 CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 8-13: TYPE LSH-PC SIMPLEX TERMINATED ON IEC 60793-2-50 CATEGORY B1.1 AND B1.3 SINGLEMODE FIBRE WITH TITANIUM COMPOSITE FERRULE FOR CATEGORY U
CEI EN 50377-7-4 : 2012 CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 7-4: LC-PC SIMPLEX TERMINATED ON IEC 60793-2-50 CATEGORY B1.1 AND B1.3 SINGLEMODE FIBRE WITH FULL ZIRCONIA FERRULE FOR CATEGORY C
BS EN 50377-2-2:2009 Connector sets and interconnect components to be used in optical fibre communication systems. Product specifications FC/APC 8 terminated on IEC 60793-2-50 category B1.1 and B1.3 singlemode fibre, with full zirconia ferrule, category C
BS EN 50411-3-6:2013 Fibre organisers and closures to be used in optical fibre communication systems. Product specifications Multimode mechanical fibre splice for use in an outdoor protected environment (Cat U)
BS EN 61753-091-2:2013 Fibre optic interconnecting devices and passive components. Performance standard Non-connectorized single-mode fibre optic pigtailed circulators for category C. Controlled environment
BS EN 50411-3-5:2015 Fibre organisers and closures to be used in optical fibre communication systems. Product specifications Wall outlet
BS EN 50516-1-1:2011 Industrial connector sets and interconnect components to be used in optical fibre control and communication systems. Product specifications Type SC-RJ PC industrial terminated on EN 60793-2-10 category A1a and A1b multimode fibre to meet the requirements of category I (industrial environments) as specified in IEC 61753-1-3
09/30197413 DC : 0 BS EN 50411-3-2 - FIBRE ORGANISERS AND CLOSURES TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 3-2: SINGLEMODE MECHANICAL FIBRE SPLICE
BS EN 61753-121-3:2010 Fibre optic interconnecting devices and passive components. Performance standard Simplex and duplex cords with single-mode fibre and cylindrical ferrule connectors for category U. Uncontrolled environment
CEI EN 61754-28 : 2013 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS - FIBRE OPTIC CONNECTOR INTERFACES - PART 28: TYPE LF3 CONNECTOR FAMILY
08/30195621 DC : 0 BS EN 50377-8-10 - CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 8-10: TYPE LSH-APC SIMPLEX TERMINATED ON IEC 60793-2-50 CATEGORY B1.1 AND B1.3 SINGLE MODE FIBRE WITH TITANIUM COMPOSITE FERRULE FOR CATEGORY C
CEI EN 50377-17-1 : 2013 CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 17-1: TYPE FPFT (FACTORY POLISHED FIELD TERMINATED) SIMPLEX CONNECTOR FACTORY TERMINATED WITH EN 60793-2-50 CATEGORY B1.3 FIBRE AND FIELD MOUNTED ONTO IEC 60793-2-50 CATEGORY B1.3 OR B6A1 OR B6A2 SINGLEMODE FIBRE, CATEGORY C
I.S. EN 61754-29:2012 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS - FIBRE OPTIC CONNECTOR INTERFACES - PART 29: TYPE BLINK CONNECTOR SERIES (IEC 61754-29:2012 (EQV))
I.S. EN 50377-17-1:2013 CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 17-1: TYPE FPFT (FACTORY POLISHED FIELD TERMINATED) SIMPLEX CONNECTOR FACTORY TERMINATED WITH EN 60793-2-50 CATEGORY B1.3 FIBRE AND FIELD MOUNTED ONTO IEC 60793-2-50 CATEGORY B1.3 OR B6A1 OR B6A2 SINGLEMODE FIBRE, CATEGORY C
I.S. EN 60794-2-51:2014 OPTICAL FIBRE CABLES - PART 2-51: INDOOR CABLES - DETAIL SPECIFICATION FOR SIMPLEX AND DUPLEX CABLES FOR USE IN CORDS FOR CONTROLLED ENVIRONMENT
I.S. EN 50377-4-4:2011 CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 4-4: TYPE SC-PC SIMPLEX TERMINATED ON IEC 60793-2-50 CATEGORY B1.1 AND B1.3 SINGLEMODE FIBRE, WITH FULL ZIRCONIA FERRULE CATEGORY U
I.S. EN 61753-061-2:2012 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS - PERFORMANCE STANDARD - PART 061-2: NON-CONNECTORIZED SINGLE-MODE FIBRE OPTIC PIGTAILED ISOLATORS FOR CATEGORY C - CONTROLLED ENVIRONMENT (IEC 61753-061-2:2012 (EQV))
EN 50516-1-1:2011/AC:2012 INDUSTRIAL CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE CONTROL AND COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 1-1: TYPE SC-RJ PC INDUSTRIAL TERMINATED ON EN 60793-2-10 CATEGORY A1A AND A1B MULTIMODE FIBRE TO MEET THE REQUIREMENTS OF CATEGORY I (INDUSTRIAL ENVIRONMENTS) AS SPECIFIED IN IEC 61753-1-3
EN 61753-121-3 : 2010 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS - PERFORMANCE STANDARD - PART 121-3: SIMPLEX AND DUPLEX CORDS WITH SINGLE-MODE FIBRE AND CYLINDRICAL FERRULE CONNECTORS FOR CATEGORY U - UNCONTROLLED ENVIRONMENT
EN 50377-14-1:2011 Connector sets and interconnect components to be used in optical fibre communication systems - Product specifications - Part 14-1: Cords with IEC 60793-2-50 singlemode category B1.1 and B1.3 fibre for category C
EN 50377-16-1:2011 Connector sets and interconnect components to be used in optical fibre communication systems - Product specifications - Part 16-1: Type LF3 APC simplex terminated on IEC 60793-2-50 category B1.1 and B1.3 singlemode fibre with titanium composite ferrule for category C
EN 61753-053-2:2014 Fibre optic interconnecting devices and passive components - Performance standard - Part 053-2: Non-connectorized single-mode fibre, electrically controlled, variable optical attenuator for category C - Controlled environments
EN 50551-1:2011 Simplex and duplex cables to be used for cords - Part 1: Blank Detail Specification and minimum requirements
EN 50377-8-11:2010 Connector sets and interconnect components to be used in optical fibre communication systems - Product specifications - Part 8-11: Type LSH-PC simplex terminated on IEC 60793-2-50 category B1.1 and B1.3 singlemode fibre with titanium composite ferrule for category C
EN 50377-7-4:2011 Connector sets and interconnect components to be used in optical fibre communication systems - Product specifications - Part 7-4: LC-PC simplex terminated on IEC 60793-2-50 category B1.1 and B1.3 singlemode fibre with full zirconia ferrule for category C
EN 50551-2:2013 Simplex and duplex cables to be used for cords - Part 2: Detailed specification and minimum requirements for a 3,0 mm simplex ruggedised single mode fibre cable to be used for patchcords/cords category U
EN 50377-4-4:2011 Connector sets and interconnect components to be used in optical fibre communication systems - Product specifications - Part 4-4: Type SC-PC simplex terminated on IEC 60793-2-50 category B1.1 and B1.3 singlemode fibre, with full zirconia ferrule category U
EN 50516-3-1:2014 Industrial connector sets and interconnect components to be used in optical fibre control and communication systems - Product specifications - Part 3-1: Type ODVA APC terminated on EN 60793-2-50 category B1.1 and B1.3 singlemode fibre to meet the requirements of category I (industrial environments) as specified in EN 50173-1 and IEC 61753-1-3
EN 50377-17-1 : 2013 CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 17-1: TYPE FPFT (FACTORY POLISHED FIELD TERMINATED) SIMPLEX CONNECTOR FACTORY TERMINATED WITH EN 60793-2-50 CATEGORY B1.3 FIBRE AND FIELD MOUNTED ONTO IEC 60793-2-50 CATEGORY B1.3 OR B6A1 OR B6A2 SINGLEMODE FIBRE, CATEGORY C
EN 50377-8-13:2010 Connector sets and interconnect components to be used in optical fibre communication systems - Product specifications - Part 8-13: Type LSH-PC simplex terminated on IEC 60793-2-50 category B1.1 and B1.3 singlemode fibre with titanium composite ferrule for category U
EN 61754-28:2012 Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 28: Type LF3 connector family
EN 61753-081-2:2014 Fibre optic interconnecting devices and passive components - Performance standard - Part 081-2: Non-connectorized single-mode fibre optic middle-scale 1 x N DWDM devices for category C - Controlled environments
EN 60794-2-51:2014 Optical fibre cables - Part 2-51: Indoor cables - Detail specification for simplex and duplex cables for use in cords for controlled environment

EN 60793-1-46:2002 Optical fibres - Part 1-46: Measurement methods and test procedures - Monitoring of changes in optical transmittance
IEC 60793-1-1 : 2017 OPTICAL FIBRES - PART 1-1: MEASUREMENT METHODS AND TEST PROCEDURES - GENERAL AND GUIDANCE
EN 60793-1-21:2002 Optical fibres - Part 1-21: Measurement methods and test procedures - Coating geometry
EN 60793-1-20:2014/AC:2016-03 OPTICAL FIBRES - PART 1-20: MEASUREMENT METHODS AND TEST PROCEDURES - FIBRE GEOMETRY (IEC 60793-1-20:2014/COR1:2016)
IEC 60793-2-10:2017 Optical fibres - Part 2-10: Product specifications - Sectional specification for category A1 multimode fibres
EN 60794-2:2017 Optical fibre cables - Part 2: Indoor cables - Sectional specification
EN 60793-1-1:2017 Optical fibres - Part 1-1: Measurement methods and test procedures - General and guidance
IEC 60189-1:2007 Low-frequency cables and wires with PVC insulation and PVC sheath - Part 1: General test and measuring methods
EN 60793-2-50:2016 Optical fibres - Part 2-50: Product specifications - Sectional specification for class B single-mode fibres
IEC TR 62222:2012 Fire performance of communication cables installed in buildings
EN 60811-1-3:1995/A1:2001 INSULATING AND SHEATHING MATERIALS OF ELECTRIC CABLES - COMMON TEST METHODS - PART 1-3: GENERAL APPLICATION - METHODS FOR DETERMINING THE DENSITY - WATER ABSORPTION TESTS - SHRINKAGE TEST
IEC 60794-1-2:2017 Optical fibre cables - Part 1-2: Generic specification - Basic optical cable test procedures - General guidance
EN 60794-1-1:2016 Optical fibre cables - Part 1-1: Generic specification - General
ISO/IEC 11801:2002 Information technology Generic cabling for customer premises
EN 60793-2-10:2017 Optical fibres - Part 2-10: Product specifications - Sectional specification for category A1 multimode fibres
IEC 60794-1-1:2015 Optical fibre cables - Part 1-1: Generic specification - General
EN 60793-1-40:2003 Optical fibres - Part 1-40: Measurement methods and test procedures - Attenuation
EN 50173-1:2011 Information technology - Generic cabling systems - Part 1: General requirements
IEC 60793-1-46:2001 Optical fibres - Part 1-46: Measurement methods and test procedures - Monitoring of changes in optical transmittance
IEC 60793-1-40:2001 Optical fibres - Part 1-40: Measurement methods and test procedures - Attenuation
IEC 60793-1-21:2001 Optical fibres - Part 1-21: Measurement methods and test procedures - Coating geometry
IEC 60793-2-50:2015 Optical fibres - Part 2-50: Product specifications - Sectional specification for class B single-mode fibres
EN 60794-1-2:2017/AC:2017-07 OPTICAL FIBRE CABLES - PART 1-2: GENERIC SPECIFICATION - BASIC OPTICAL CABLE TEST PROCEDURES - GENERAL GUIDANCE (IEC 60794-1-2:2017)
IEC 60794-2:2017 Optical fibre cables - Part 2: Indoor cables - Sectional specification
IEC 60811-1-3:1993+AMD1:2001 CSV Common test methods for insulating and sheathing materials of electric and optical cables - Part 1-3: General application -Methods for determining the density - Water absorption tests - Shrinkage test
IEC 60793-1-20:2014 Optical fibres - Part 1-20: Measurement methods and test procedures - Fibre geometry
IEC 60811-1-4:1985 Common test methods for insulating and sheathing materials of electric cables - Part 1: Methods for general application - Section Four: Tests at low temperature
IEC 60068-2-14:2009 Environmental testing - Part 2-14: Tests - Test N: Change of temperature
EN 60068-2-14:2009 Environmental testing - Part 2-14: Tests - Test N: Change of temperature
EN 60811-1-4:1995/A2:2001 INSULATING AND SHEATHING MATERIALS OF ELECTRIC CABLES - COMMON TEST METHODS - PART 1-4: GENERAL APPLICATION - TESTS AT LOW TEMPERATURE

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more