Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

EN ISO 21003-3:2008

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Multilayer piping systems for hot and cold water installations inside buildings - Part 3: Fittings (ISO 21003-3:2008)
Superseded date

06-11-2021

Published date

01-07-2008

Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Material characteristics
   5.1 Plastics fitting materials specified in reference
        product standards
   5.2 Plastics fitting materials not specified in reference
        product standards
   5.3 Metallic fitting material
   5.4 Influence on water intended for human consumption
6 General characteristics
   6.1 Appearance
   6.2 Opacity
7 Geometrical characteristics
   7.1 General
   7.2 Dimensions of sockets for socket weld, electrofusion
        and solvent-cemented fittings
   7.3 Dimensions of metallic fittings
8 Mechanical characteristics of plastics fittings (internal
   pressure test)
   8.1 General
   8.2 Plastics fitting materials specified in reference
        product standards
   8.3 Plastics fitting materials not specified in reference
        product standards
9 Physical and chemical characteristics of plastics fittings
   9.1 Plastics fitting materials specified in reference
        product standards
   9.2 Plastics fitting materials not specified in reference
        product standards
   9.3 Sealing elements
10 Performance requirements
11 Marking
   11.1 General requirements
   11.2 Minimum required marking
Annex A (normative) - List of reference product standards
Bibliography

ISO 21003-3:2008 specifies the characteristics of fittings for multilayer piping systems intended to be used for hot and cold water installations inside buildings for the conveyance of water — whether or not the water is intended for human consumption (domestic systems) or for heating systems — under specified design pressures and temperatures appropriate to the class of applicationIt also specifies the test parameters for the test methods referred to in this part of ISO 21003.ISO 21003 is a reference product standard. It is applicable to multilayer pipes, fittings, their joints, and also to joints with components made of other plastics and non-plastics materials intended to be used for hot and cold water installations. ISO 21003-3 is intended for use only in conjunction with all the other parts of ISO 21003.

Committee
CEN/TC 155
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Superseded
SupersededBy

11/30197617 DC : 0 BS ISO 11855-5 - BUILDING ENVIRONMENT DESIGN - STANDARDS FOR THE DESIGN, CONSTRUCTION AND OPERATION OF RADIANT HEATING AND COOLING SYSTEMS - PART 5: INSTALLATION
09/30202316 DC : 0 BS EN 12514-4 - PARTS FOR SUPPLY SYSTEMS FOR CONSUMING UNITS WITH LIQUID FUELS - PART 4: SAFETY REQUIREMENTS AND TESTS - PIPINGS AND PARTS WITHIN PIPELINES
CEN ISO/TS 21003-7:2008/A1:2010 MULTILAYER PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS INSIDE BUILDINGS - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY
NF EN 1264-4 : 2010 WATER BASED SURFACE EMBEDDED HEATING AND COOLING SYSTEMS - PART 4: INSTALLATION
I.S. EN 1264-4:2009 WATER BASED SURFACE EMBEDDED HEATING AND COOLING SYSTEMS - PART 4: INSTALLATION
UNI EN 806-4 : 2010 SPECIFICATIONS FOR INSTALLATIONS INSIDE BUILDINGS CONVEYING WATER FOR HUMAN CONSUMPTION - PART 4: INSTALLATION
BS EN 806-4:2010 Specifications for installations inside buildings conveying water for human consumption Installation
EN 1264-4:2009 Water based surface embedded heating and cooling systems - Part 4: Installation
ISO/TS 21003-7:2008 Multilayer piping systems for hot and cold water installations inside buildings Part 7: Guidance for the assessment of conformity
S.R. CEN ISO TS 21003-7:2008 MULTILAYER PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS INSIDE BUILDINGS - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY
NF EN 806-4 : 2010 SPECIFICATIONS FOR INSTALLATIONS INSIDE BUILDINGS CONVEYING WATER FOR HUMAN CONSUMPTION - PART 4: INSTALLATION
DIN EN 1264-4:2009-11 Water based surface embedded heating and cooling systems - Part 4: Installation
BS EN 1264-4:2009 Water based surface embedded heating and cooling systems Installation
DIN EN 806-4:2010-06 Specifications for installations inside buildings conveying water for human consumption - Part 4: Installation
DD CEN ISO/TS 21003-7 : 2008 MULTILAYER PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS INSIDE BUILDINGS - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY
UNI EN 1264-4 : 2009 WATER BASED SURFACE EMBEDDED HEATING AND COOLING SYSTEMS - PART 4: INSTALLATION
I.S. EN 806-4:2010 SPECIFICATIONS FOR INSTALLATIONS INSIDE BUILDINGS CONVEYING WATER FOR HUMAN CONSUMPTION - PART 4: INSTALLATION
EN 806-4:2010 Specifications for installations inside buildings conveying water for human consumption - Part 4: Installation
UNI CEN ISO/TS 21003-7 : 2010 MULTILAYER PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS INSIDE BUILDINGS - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY
UNE-EN 1264-4:2010 Water based surface embedded heating and cooling systems - Part 4: Installation

EN 1254-3:1998 Copper and copper alloys - Plumbing fittings - Part 3: Fittings with compression ends for use with plastics pipes
EN 681-1:1996/A3:2005 ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 1: VULCANIZED RUBBER
ISO 15874-3:2013 Plastics piping systems for hot and cold water installations — Polypropylene (PP) — Part 3: Fittings
ISO 15877-3:2009 Plastics piping systems for hot and cold water installations Chlorinated poly(vinyl chloride) (PVC-C) Part 3: Fittings
ISO 1167-2:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces
BS 7291-2:2006 Thermoplastics pipes and associated fittings for hot and cold water for domestic purposes and heating installations in buildings Specification for polybutylene (PB) pipes and associated fittings
ISO 1167-4:2007 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 4: Preparation of assemblies
ISO 9080:2012 Plastics piping and ducting systems — Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation
EN 681-2:2000/A2:2005 ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 2: THERMOPLASTIC ELASTOMERS
ISO 21003-5:2008 Multilayer piping systems for hot and cold water installations inside buildings — Part 5: Fitness for purpose of the system
ISO 3126:2005 Plastics piping systems Plastics components Determination of dimensions
ISO 15876-3:2017 Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 3: Fittings
ISO 1167-3:2007 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 3: Preparation of components
ISO 21003-2:2008 Multilayer piping systems for hot and cold water installations inside buildings — Part 2: Pipes
ISO 21003-1:2008 Multilayer piping systems for hot and cold water installations inside buildings — Part 1: General
ISO 22391-3:2009 Plastics piping systems for hot and cold water installations Polyethylene of raised temperature resistance (PE-RT) Part 3: Fittings
BS 7291-4:1990 Thermoplastics pipes and associated fittings for hot and cold water for domestic purposes and heating installations in buildings Specification for chlorinated polyvinyl chloride (PVC-C) pipes and associated fittings and solvent cement
ISO/TS 21003-7:2008 Multilayer piping systems for hot and cold water installations inside buildings Part 7: Guidance for the assessment of conformity
ISO 15875-3:2003 Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X) — Part 3: Fittings
EN 10226-1:2004 Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation
ISO 228-1:2000 Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation
ISO 7686:2005 Plastics pipes and fittings — Determination of opacity
EN 10088-1:2014 Stainless steels - Part 1: List of stainless steels
ISO 1167-1:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more