EN ISO 8503-4:2012
Current
The latest, up-to-date edition.
Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blast-cleaned steel substrates - Part 4: Method for the calibration of ISO surface profile comparators and for the determination of surface profile - Stylus instrument procedure (ISO 8503-4:2012)
15-02-2012
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Principle
5 Apparatus
6 Test surfaces
7 Procedure for measurement of maximum peak-to-valley
height, R[y]
8 Calculation and expression of results
9 Test report
Annex A (normative) - Test report for the calibration
of ISO surface profile comparators and for the
determination of surface profiles
Annex B (normative) - Form for recording surface profile
measurements made in accordance with ISO 8503-4
Annex C (informative) - Guidance notes for the preparation
and measurement of replicas
Bibliography
ISO 8503-4:2012 specifies the stylus instrument and describes the procedure for calibrating ISO surface profile comparators conforming to the requirements of ISO 8503-1.It is also applicable to the determination of the surface profile, within the range 20 μm to 200 μm, of essentially planar blast-cleaned steel. The determination can be carried out on a representative section of the blast-cleaned surface or, if direct observation of the surface is not feasible, on a replica of the surface.
| Committee |
CEN/TC 139
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Current
|
| Standards | Relationship |
| ISO 8503-4:2012 | Identical |
| NF EN ISO 8503-4 : 2012 | Identical |
| NBN EN ISO 8503-4 : 2012 | Identical |
| NEN EN ISO 8503-4 : 2012 | Identical |
| NS EN ISO 8503-4 : 2012 | Identical |
| I.S. EN ISO 8503-4:2012 | Identical |
| PN EN ISO 8503-4 : 2012 | Identical |
| BS EN ISO 8503-4:1995 | Identical |
| DIN EN ISO 8503-4:2012-06 | Identical |
| BS EN ISO 8503-4:2012 | Equivalent |
| BS EN ISO 8503-4:2012 | Identical |
| UNE-EN ISO 8503-4:2012 | Identical |
| EN 10339:2007 | Steel tubes for onshore and offshore water pipelines - Internal liquid applied epoxy linings for corrosion protection |
| EN 10301:2003 | Steel tubes and fittings for on and offshore pipelines - Internal coating for the reduction of friction for conveyance of non corrosive gas |
| BS EN 13507:2010 | Thermal spraying. Pre-treatment of surfaces of metallic parts and components for thermal spraying |
| 16/30339226 DC : DRAFT JUNE 2016 | BS EN 13507 - THERMAL SPRAYING - PRE-TREATMENT OF SURFACES OF METALLIC PARTS AND COMPONENTS FOR THERMAL SPRAYING |
| PREN 13507 : DRAFT 2016 | THERMAL SPRAYING - PRE-TREATMENT OF SURFACES OF METALLIC PARTS AND COMPONENTS FOR THERMAL SPRAYING |
| 04/30114371 DC : DRAFT JUN 2004 | EN 10339 - STEEL TUBES FOR ONSHORE AND OFFSHORE WATER PIPELINES - INTERNAL LIQUID APPLIED EPOXY LININGS FOR CORROSION PROTECTION |
| I.S. EN 13507:2010 | THERMAL SPRAYING - PRE-TREATMENT OF SURFACES OF METALLIC PARTS AND COMPONENTS FOR THERMAL SPRAYING |
| EN 13507:2010 | Thermal spraying - Pre-treatment of surfaces of metallic parts and components for thermal spraying |
| BS EN ISO 8504-1:2001 | Preparation of steel substrates before application of paints and related products. Surface preparation methods General principles |
| BS EN 10301:2003 | Steel tubes and fittings for on and offshore pipelines. Internal coating for the reduction of friction for conveyance of non corrosive gas |
| BS EN 10339:2007 | Steel tubes for onshore and offshore water pipelines. Internal liquid applied epoxy linings for corrosion protection |
| EN ISO 8504-1:2001 | Preparation of steel substrates before application of paints and related products - Surface preparation methods - Part 1: General principles (ISO 8504-1:2000) |
| 08/30183878 DC : DRAFT AUG 2008 | BS EN 13507 - THERMAL SPRAYING - PRE-TREATMENT OF SURFACES OF METALLIC PARTS AND COMPONENTS FOR THERMAL SPRAYING |
| DIN EN 13507:2016-07 (Draft) | THERMAL SPRAYING - PRE-TREATMENT OF SURFACES OF METALLIC PARTS AND COMPONENTS FOR THERMAL SPRAYING |
| I.S. EN ISO 8504-1:2001 | PREPARATION OF STEEL SUBSTRATES BEFORE APPLICATION OF PAINTS AND RELATED PRODUCTS - SURFACE PREPARATION METHODS - PART 1: GENERAL PRINCIPLES |
| DIN EN 10301:2004-01 | Steel tubes and fittings for on and offshore pipelines - Internal coating for the reduction of friction for conveyance of non corrosive gas |
| DIN EN 10339:2007-05 | Steel tubes for onshore and offshore water pipelines - Internal liquid applied epoxy linings for corrosion protection |
| UNE-EN 13507:2011 | Thermal spraying - Pre-treatment of surfaces of metallic parts and components for thermal spraying |
| ISO 4287:1997 | Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms, definitions and surface texture parameters |
| ISO 8503-2:2012 | Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 2: Method for the grading of surface profile of abrasive blast-cleaned steel — Comparator procedure |
| ISO 8503-3:2012 | Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 3: Method for the calibration of ISO surface profile comparators and for the determination of surface profile — Focusing microscope procedure |
| ISO 5436-2:2012 | Geometrical product specifications (GPS) — Surface texture: Profile method; Measurement standards — Part 2: Software measurement standards |
| ISO 3274:1996 | Geometrical Product Specifications (GPS) — Surface texture: Profile method — Nominal characteristics of contact (stylus) instruments |
| ISO 5436-1:2000 | Geometrical Product Specifications (GPS) — Surface texture: Profile method; Measurement standards — Part 1: Material measures |
| ISO 8503-1:2012 | Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 1: Specifications and definitions for ISO surface profile comparators for the assessment of abrasive blast-cleaned surfaces |
| ISO 8504-2:2000 | Preparation of steel substrates before application of paints and related products — Surface preparation methods — Part 2: Abrasive blast-cleaning |