I.S. EN 10025-6:2004
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
HOT ROLLED PRODUCTS OF STRUCTURAL STEELS - PART 6: TECHNICAL DELIVERY CONDITIONS FOR FLAT PRODUCTS OF HIGH YIELD STRENGTH STRUCTURAL STEELS IN THE QUENCHED AND TEMPERED CONDITION
Hardcopy , PDF
English
01-01-2004
04-09-2019
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Foreword
1 Scope
2 Normative references
2.1 General standards
2.2 Standards on dimensions and tolerances
2.3 Standards on testing
3 Terms and definitions
4 Classification and designation
4.1 Classification
4.1.1 Main quality classes
4.1.2 Grades and qualities
4.2 Designation
5 Information to be supplied by the purchaser
5.1 Mandatory information
5.2 Options
6 Manufacturing process
6.1 Steel making process
6.2 Deoxidation or grain size
6.3 Delivery conditions
7 Requirements
7.1 General
7.2 Chemical composition
7.3 Mechanical properties
7.3.1 General
7.3.2 Impact properties
7.3.3 Improved deformation properties
perpendicular to the surface
7.4 Technological properties
7.4.1 Weldability
7.4.2 Formability
7.4.3 Suitability for hot-dip zinc-coating
7.5 Surface properties
7.6 Internal soundness
7.7 Tolerances on dimensions and shape, mass
8 Inspection
8.1 General
8.2 Type of inspection and inspection document
8.3 Frequency of testing
8.3.1 Sampling
8.3.2 Test units
8.3.3 Verification of chemical composition
8.4 Tests to be carried out for specific inspection
9 Preparation of samples and test pieces
9.1 Selection and preparation of samples for chemical
analysis
9.2 Location and orientation of samples and test pieces
for mechanical tests
9.2.1 General
9.2.2 Preparation of samples
9.2.3 Preparation of test pieces
9.2.4 Impact test pieces
9.3 Identification of samples and test pieces
10 Test methods
10.1 Chemical analysis
10.2 Mechanical tests
10.3 Ultrasonic testing
10.4 Retests
11 Marking, labelling, packaging
12 Complaints
13 Options
Annex A (informative) - List of corresponding former
designations
Annex B (informative) - List of national standards which
correspond with ECSC IC 2 referenced
Annex C (informative) - Minimum recommended inside bend radii
for flanging
Bibliography
Defines requirements for flat products of high yield strength alloy special steels.
| DevelopmentNote |
Supersedes I.S. EN 10137-1 and I.S. EN 10137-2. (05/2005) 2004 Edition Re-issued in July 2009 & incorporates AMD 1 2009. (08/2009)
|
| DocumentType |
Standard
|
| Pages |
26
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| NS EN 10025-6 : 2004 + A1 2009 | Identical |
| NBN EN 10025-6 : 2004 + A1 2009 | Identical |
| EN 10025-6:2004+A1:2009 | Identical |
| DIN EN 10025-6:2011-04 (Draft) | Identical |
| NEN EN 10025-6 : 2004 + A1 2009 | Identical |
| BS EN 10025-6 : 2004 | Identical |
| NF EN 10025-6 : 2005 + A1 2009 | Identical |
| EN 10025-6:2004 | Equivalent |
| UNE-EN 10025-6:2007 | Identical |
| DIN EN 10025-6:2009-08 | Identical |
A newer version of this standard is available.
View Current Edition
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.