I.S. EN 61158-2:2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
INDUSTRIAL COMMUNICATION NETWORKS - FIELDBUS SPECIFICATIONS - PART 2: PHYSICAL LAYER SPECIFICATION AND SERVICE DEFINITION
Hardcopy , PDF
English
01-01-2014
18-12-2023
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
FOREWORD
0 Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviations
5 DLL - PhL interface
6 Systems management - PhL interface
7 DCE independent sublayer (DIS)
8 DTE - DCE interface and MIS-specific functions
9 Medium dependent sublayer (MDS)
10 MDS - MAU interface
11 Types 1 and 7: Medium attachment unit: voltage mode,
linear-bus-topology 150 Omega twisted-pair wire medium
12 Types 1 and 3: Medium attachment unit: 31,25 kbit/s,
voltage-mode with low-power option, bus- and
tree-topology, 100 Omega wire medium
13 Type 1: Medium attachment unit: current mode,
twisted-pair wire medium
14 Type 1: Medium attachment unit: current mode (1 A),
twisted-pair wire medium
15 Types 1 and 7: Medium attachment unit: dual-fiber
optical media
16 Type 1: Medium attachment unit: 31,25 kbit/s,
single-fiber optical medium
17 Void
18 Type 2: Medium attachment unit: 5 Mbit/s,
voltage-mode, coaxial wire medium
19 Type 2: Medium attachment unit: 5 Mbit/s,
optical medium
20 Type 2: Medium attachment unit: network access
port (NAP)
21 Type 3: Medium attachment unit: synchronous
transmission, 31,25 kbit/s, voltage mode,
wire medium
22 Type 3: Medium attachment unit: asynchronous
transmission, wire medium
23 Type 3: Medium attachment unit: asynchronous
transmission, optical medium
24 Type 4: Medium attachment unit: RS-485
25 Void
26 Void
27 Type 8: Medium attachment unit: twisted-pair
wire medium
28 Type 8: Medium attachment unit: optical media
29 Type 12: Medium attachment unit: electrical medium
30 Type 16: Medium attachment unit: optical fiber
medium at 2, 4, 8 and 16 Mbit/s
31 Type 18: Medium attachment unit: basic medium
32 Type 18: Medium attachment unit: powered medium
33 Type 24: Medium attachment unit: twisted-pair wire medium
34 Type 20: Medium attachment unit: FSK medium
Annex A (normative) - Type 1: Connector specification
Annex B (informative) - Types 1 and 3: Cable specifications and
trunk and spur lengths for the 31,25 kbit/s
voltage-mode MAU
Annex C (informative) - Types 1 and 7: Optical passive stars
Annex D (informative) - Types 1 and 7: Star topology
Annex E (informative) - Type 1: Alternate fibers
Annex F (normative) - Type 2: Connector specification
Annex G (normative) - Type 2: Repeater machine sublayers
(RM, RRM) and redundant PhLs
Annex H (informative) - Type 2: Reference design examples
Annex I (normative) - Type 3: Connector specification
Annex J (normative) - Type 3: Redundancy of PhL
and medium
Annex K (normative) - Type 3: Optical network topology
Annex L (informative) - Type 3: Reference design
examples for asynchronous transmission, wire
medium, intrinsically safe
Annex M (normative) - Type 8: Connector specification
Annex N (normative) - Type 16: Connector specification
Annex O (normative) - Type 16: Optical network topology
Annex P (informative) - Type 16: Reference design example
Annex Q (normative) - Type 18: Connector specification
Annex R (normative) - Type 18: Media cable specifications
Annex S (normative) - Type 24: Connector specification
Annex T (informative) - Type 20: Network topology, cable
characteristics and lengths, power distribution through
barriers, and shielding and grounding
Bibliography
Annex ZA (normative) - Normative references to
International publications with their
corresponding European publications
Describes the requirements for fieldbus component parts. It also specifies the media and network configuration requirements necessary to ensure agreed levels of: a) data integrity before data-link Layer error checking; b) interoperability between devices at the Physical Layer.
| DevelopmentNote |
Supersedes I.S. EN 50170 and I.S. EN 50254 (09/2004) Supersedes I.S. EN 61491. (10/2009) For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
|
| DocumentType |
Standard
|
| Pages |
1024
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| BS EN 61158-2:2014 | Identical |
| EN 61158-2:2014 | Identical |
| NF EN 61158-2 : 2015 | Identical |
| NBN EN 61158-2 : 2014 | Identical |
| DIN EN 61158-2:2015-02 | Identical |
| IEC 61158-2:2014 | Equivalent |
| UNE-EN 61158-2:2014 | Equivalent |
A newer version of this standard is available.
View Current Edition
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.