IEC 61518:2001
Current
The latest, up-to-date edition.
Mating dimensions between differential pressure (type) measuring instruments and flanged-on shut-off devices up to 413 BAR (41,3 MPa)
Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users
English, English - French
24-01-2001
FOREWORD
INTRODUCTION
Clause
1 Scope
2 Normative references
3 Dimensions
3.1 Connection dimensions at the differential
pressure (type) instrument
3.2 Connection dimensions at the shut-off device
3.3 Seal rings
3.4 Flange connection (see figures 4 and 5)
4 Installation
5 Material for the bolts
6 Marking
Applicable to differential pressure (type) measuring instruments(instrument) with a shut-off device (manifold) directly bolted on to them.
| Committee |
TC 65/SC 65B
|
| DevelopmentNote |
Also numbered as BS EN 61518. (05/2001) Stability Date: 2024. (09/2017)
|
| DocumentType |
Standard
|
| Pages |
13
|
| PublisherName |
International Electrotechnical Committee
|
| Status |
Current
|
| Standards | Relationship |
| NF EN 61518 : 2001 | Identical |
| NEN EN IEC 61518 : 2001 C11 2002 | Identical |
| I.S. EN 61518:2001 | Identical |
| PN EN 61518 : 2004 | Identical |
| EN 61518:2001/corrigendum:2002 | Identical |
| DIN EN 61518:2002-06 | Identical |
| UNE-EN 61518:2001 | Identical |
| IEC 62828-2:2017 | Reference conditions and procedures for testing industrial and process measurement transmitters - Part 2: Specific procedures for pressure transmitters |
| API 551 : 2016 | PROCESS MEASUREMENT |
| 13/30287777 DC : 0 | BS EN 62828-2 ED 1.0 - REFERENCE CONDITIONS AND PROCEDURES FOR INDUSTRIAL MEASUREMENT TRANSMITTERS - PART 2: SPECIFIC PROCEDURES FOR PRESSURE TRANSMITTERS |
| I.S. EN IEC 62828-2:2018 | REFERENCE CONDITIONS AND PROCEDURES FOR TESTING INDUSTRIAL AND PROCESS MEASUREMENT TRANSMITTERS - PART 2: SPECIFIC PROCEDURES FOR PRESSURE TRANSMITTERS |
| ASME B18.2.1 : 2012 | SQUARE, HEX, HEAVY HEX, AND ASKEW HEAD BOLTS AND HEX, HEAVY HEX, HEX FLANGE, LOBED HEAD, AND LAG SCREWS (INCH SERIES) |
| ISO 3506-1:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners — Part 1: Bolts, screws and studs |
| ISO 3506:1979 | Corrosion-resistant stainless steel fasteners — Specifications |
| ISO 3506-3:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners — Part 3: Set screws and similar fasteners not under tensile stress |
| ASTM A 449 : 2014 : REDLINE | Standard Specification for Hex Cap Screws, Bolts and Studs, Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength, General Use |
| ISO 3601-1:2012 | Fluid power systems — O-rings — Part 1: Inside diameters, cross-sections, tolerances and designation codes |
| ISO 3601-3:2005 | Fluid power systems — O-rings — Part 3: Quality acceptance criteria |
| ISO 48:2010 | Rubber, vulcanized or thermoplastic — Determination of hardness (hardness between 10 IRHD and 100 IRHD) |
| ISO 3506-2:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners — Part 2: Nuts |
| ISO 1629:2013 | Rubber and latices — Nomenclature |
| ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.