IEC 62301:2011
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Household electrical appliances - Measurement of standby power
Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users
English, English - French
27-01-2011
22-05-2026
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 General conditions for measurements
5 Measurements
6 Test report
Annex A (informative) - Guidance on modes and
functions for selected product types
Annex B (informative) - Notes on the measurement
of low power modes
Annex C (informative) - Converting power values to
energy
Annex D (informative) - Determination of uncertainty
of measurement
Bibliography
IEC 62301:2011 specifies methods of measurement of electrical power consumption in standby mode(s) and other low power modes (off mode and network mode), as applicable. It is applicable to electrical products with a rated input voltage or voltage range that lies wholly or partly in the range 100 V a.c. to 250 V a.c. for single phase products and 130 V a.c. to 480 V a.c. for other products. The objective of this standard is to provide a method of test to determine the power consumption of a range of products in relevant low power modes (see 3.4), generally where the product is not in active mode (i.e. not performing a primary function). This standard does not specify safety requirements. It does not specify minimum performance requirements nor does it set maximum limits on power or energy consumption. This second edition cancels and replaces the first edition published in 2005 and constitutes a technical revision. The main changes from the previous edition are as follows:
- greater detail in set-up procedures and introduction of stability requirements for all measurement methods to ensure that results are as representative as possible;
- refinement of measurement uncertainty requirements for power measuring instruments, especially for more difficult loads with high crest factor and/or low power factor;
- updated guidance on product configuration, instrumentation and calculation of measurement uncertainty;
- inclusion of definitions for low power modes as requested by TC59 and use of these new definitions and more rigorous terminology throughout the standard;
- inclusion of specific test conditions where power consumption is affected by ambient illumination.
| Committee |
TC 59
|
| DevelopmentNote |
Stability Date: 2019. (09/2017) This standard was just updated in our system however it was originally released on 01-2011
|
| DocumentType |
Standard
|
| ISBN |
978-2-88912-329-2
|
| Pages |
92
|
| PublisherName |
International Electrotechnical Committee
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| AS/NZS IEC 62301:2014 | Identical |
| VDE 0705-2301:2011-12 | Identical |
| DIN EN 50564:2011-12 | Identical |
| OVE EN IEC 60879:2020 07 01 | Identical |
| EN 50564:2011 | Identical |
| GOST IEC 62301 : 2016 | Identical |
| GOST R IEC 62301 : 2011 | Identical |
| EN 62301:2005 | Identical |
| I.S. EN 62301:2005 | Identical |
| BS EN 62301:2005 | Identical |
| NEN EN IEC 62301 : 2005 | Identical |
| DIN EN 62301:2006-05 | Identical |
| UNE-EN 50564:2012 | Identical |
| UNE-EN 62301:2006 | Identical |
| CEI EN 62301 : 2006 | Identical |
A newer version of this standard is available.
View Current Edition
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.