IEC PAS 61076-3-110:2002

FOREWORD
1 Scope
   1.1 Normative references
2 IEC type designation
   2.1 Terminology
   2.2 Marking
   2.3 Main functions
   2.4 Interchangeability
       2.4.1 Intermateability
       2.4.2 Interoperability
             2.4.2.1 General
             2.4.2.2 Requirements
3 Common features and isometric view
   3.1 Isometric view
   3.2 Mating information
       3.2.1 Contacts interface
       3.2.2 Fixed connector contacts
       3.2.3 Free connector contacts
4 Dimensions
   4.1 General
   4.2 Type C free connectors
       4.2.1 Free connector, side protrusions dimensions
   4.3 Terminations
5 Gauges
   5.1 Fixed connectors
   5.2 Free connectors
   5.3 Switch actuator gauges
6 Characteristics
   6.1 General
   6.2 Classification into climatic categories
   6.3 Creepage and clearance distance
   6.4 Electrical characteristics
       6.4.1 Voltage proof
       6.4.2 Current-carrying capacity
       6.4.3 Initial contact resistance
       6.4.4 Input to output resistance
       6.4.5 Input to output resistance unbalance
       6.4.6 Initial insulation resistance
   6.5 Transmission characteristics, category
       6.5.1 Insertion loss
       6.5.2 Return loss
       6.5.3 Propagation delay
       6.5.4 Delay skew
       6.5.5 NEXT loss
       6.5.6 FEXT loss
       6.5.7 Longitudinal conversion loss
       6.5.8 Coupling attenuation
       6.5.9 Transfer impedance
   6.6 Mechanical characteristics
       6.6.1 Mechanical operation including switch
       6.6.2 Effectiveness of connector coupling devices
       6.6.3 Insertion and withdrawal forces
7 Tests and test schedule
   7.1 General
   7.2 Test procedures and measuring methods
   7.3 Preconditioning
   7.4 Wiring and mounting of specimens
       7.4.1 Wiring
       7.4.2 Mounting
       7.4.3 Arrangement for contact resistance
             measurement
       7.4.4 Test procedure
       7.4.5 Arrangement for dynamic stress tests (test
             phases AP6, AP7)
   7.5 Test schedules
       7.5.1 Basic (minimum) test schedule
       7.5.2 Full test schedule
             7.5.2.1 Test group P preliminary
             7.5.2.2 Test group AP
             7.5.2.3 Test group BP
             7.5.2.4 Test group CP
             7.5.2.5 Test group DP
             7.5.2.6 Test group EP
             7.5.2.7 Test group FP
Annex A (normative) Gauging requirements
Annex B (normative) Locking device mechanical operation -
        test procedure and requirements
Annex C (normative) High frequency (category 7)
        transmission interoperability testing
Annex D (normative) General requirements for the
        measurement set-up
Annex E (normative) Insertion loss
Annex F (normative) Return loss
Annex G (normative) Near end cross talk
Annex H (normative) Far end cross talk
Annex I (normative) Longitudinal conversion loss
Annex J (normative) Transfer impedance
Annex K (normative) Coupling attenuation
Annex L (normative) Termination of balun
Annex M (normative) Gauge dimensions supplement for switch
        actuator for use with standard IEC 61076-3-110
        series connectors

Covers 8-way connectors up to 4 pairs to be used up to 600 MHz, when used with an appropriate cable. These cables are specified in IEC 61156. The connectors are compatible with those already defined in IEC 60603-7-7.