ANSI/NEMA LD 3:2005
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
HIGH-PRESSURE DECORATIVE LAMINATES
Hardcopy , PDF
English
20-06-2005
19-04-2023
Foreword
Members
Section 1 - GENERAL
1.1 SCOPE
1.2 REFERENCED STANDARDS
1.3 TYPES AND DESCRIPTIONS
1.3.1 General Purpose Type
1.3.2 Postforming Type
1.3.3 Flame Retardant Type
1.3.4 High Wear Type
1.3.5 Specific Purpose Type
1.3.6 Compact Laminate Type
1.3.7 Cabinet Liner Type
1.3.8 Backer Type
1.3.9 Other Types
1.4 CONFORMANCE WITH FOOD, DRUG, AND COSMETICS ACT
1.5 FIRE RATING
1.6 VISUAL INSPECTION
1.7 SURFACE FINISHES
Section 2 - PERFORMANCE PROPERTIES AND VALUES
2.1 PERFORMANCE PROPERTIES
Section 3 - TEST METHODS
3.1 APPEARANCE
3.1.1 Scope
3.1.2 Test Apparatus and Materials
3.1.3 Test Specimens
3.1.4 Test for Visual Defects
3.1.5 Test for Thickness
3.1.6 Test for Flatness
3.1.7 Test for Broken Corners
3.1.8 Test for Squareness
3.1.9 Test for Edge Straightness
3.1.10 Sanding
3.1.11 Test Report
3.2 SURFACE FINISH
3.3 LIGHT RESISTANCE
3.4 CLEANABILITY/STAIN RESISTANCE
3.5 BOILING WATER RESISTANCE
3.6 HIGH TEMPERATURE RESISTANCE
3.6.1 Scope
3.6.2 Hot Wax Method
3.6.3 Hot Oil Method
3.7 SCRATCH RESISTANCE (Values under consideration)
3.7.1 Scope
3.7.2 Linear Glass Scratch Method
3.7.3 Diamond Scratch Method
3.8 BALL IMPACT RESISTANCE
3.9 DART IMPACT RESISTANCE
3.10 RADIANT HEAT RESISTANCE
3.10.1 Scope
3.10.2 Coil Element Method
3.10.3 Strip Element Method
3.11 DIMENSIONAL CHANGE
3.12 ROOM TEMPERATURE DIMENSIONAL STABILITY
3.13 WEAR RESISTANCE
3.14 FORMABILITY
3.15 BLISTER RESISTANCE
Annex A APPLICATION, FABRICATION, AND INSTALLATION
A.1 INTRODUCTION
A.2 GENERAL DISCUSSION
A.3 MATERIALS
A.3.1 High-Pressure Decorative Laminate
A.3.2 Adhesives
A.3.3 Substrate
A.3.4 Factors Affecting Bonded Assemblies
A.4 CONDITIONING AND STORAGE OF MATERIALS PRIOR TO
FABRICATION
A.5 FABRICATION TOOLING
A.5.1 Sawing
A.5.2 Routing
A.5.3 Sanding
A.5.4 Drilling
A.6 GENERAL RULES FOR FABRICATION AND INSTALLATION
A.6.1 Fabrication in the Shop
A.6.2 Postforming Laminates
A.6.3 Installation on the Job
A.6.4 Field Working of Bonded Assemblies
A.7 TYPICAL PROBLEMS - CAUSES AND PREVENTION
Annex B CARE AND CLEANING OF LAMINATES
Annex C PERCEPTION OF SCRATCHES
Annex D WEAR RESISTANCE CHART
Describes high pressure decorative laminate (HPDL) sheets which consist of paper, fabrics, or other core materials that have been laminated at pressures of more than 5.0 MPa using thermosetting condensation resins as binders.
| DevelopmentNote |
Supersedes L P 508 (H). (05/2004) Supersedes NEMA LD 3.1. (04/2006)
|
| DocumentType |
Standard
|
| Pages |
74
|
| ProductNote |
Publisher update - NEMA 2026 Standards – Removed from purchase for this standard as per advice from publisher dated – 5th Feb 2026
|
| PublisherName |
National Electrical Manufacturers Association
|
| Status |
Withdrawn
|
| Supersedes |
This standard has been withdrawn and is no longer current. No replacement edition is available.
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.