NF EN 15061 : 2007 + A1 2009
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR STRIP PROCESSING LINE MACHINERY AND EQUIPMENT
Published date
12-01-2013
Publisher
Superseded date
31-03-2022
Superseded by
Sorry this product is not available in your region.
Avant-propos
Introduction
1 Domaine d'application
2 Références normatives
3 Termes et définitions
4 Liste des phénomènes dangereux significatifs
5 Prescriptions et/ou mesures de sécurité
5.1 Prescriptions générales de conception
5.2 Liste des phénomènes dangereux significatifs, situations
dangereuses, prescriptions et/ou mesures de sécurité pour
l'équipement terminal
5.3 Liste des phénomènes dangereux significatifs, situations
dangereuses, prescriptions et/ou mesures de sécurité pour
l'équipement de traitement
5.4 Prescriptions et mesures de sécurité spéciales
6 Vérification des prescriptions et/ou mesures de sécurité
7 Informations pour l'utilisation
7.1 Généralités
7.2 Signaux de sécurité et dispositifs d'avertissement
7.3 Marquage minimal
7.4 Notice d'instructions
7.5 Manuel de maintenance
Annexe A (normative) Prescriptions et/ou mesures de
sécurité pour les équipements électriques
Annexe B (normative) Code d'essai acoustique
Annexe C (informative) Exemple d'instructions de sécurité
du fabricant pour la maintenance sur les lignes
de traitement des bandes
Annexe D (informative) Exemples de solutions
Annexe ZA (informative) Relation entre la présente Norme
européenne et les exigences essentielles de
la Directive UE 98/37/CE
Annexe ZB (informative) Relation entre la présente Norme
européenne et les exigences essentielles de la
Directive UE 2006/42/CE
Bibliographie
Describes the health and safety requirements of strip processing lines.
| DevelopmentNote |
Indice de classement: E88-040. PR NF EN 15061 December 2004. (12/2004) 2007 Edition Re-issued in February 2009 & incorporates AMD 1 2009. (02/2009)
|
| DocumentType |
Standard
|
| PublisherName |
Association Francaise de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| DIN EN 15061:2009-05 | Identical |
| NS EN 15061 : 2007 + A1 2008 | Identical |
| NEN EN 15061 : 2007 + A1 2009 | Identical |
| I.S. EN 15061:2007 | Identical |
| BS EN 15061 : 2007 | Identical |
| EN 15061:2007+A1:2008 | Identical |
| NF EN ISO 13857 : 2008 | SAFETY OF MACHINERY - SAFETY DISTANCES TO PREVENT HAZARD ZONES BEING REACHED BY UPPER AND LOWER LIMBS |
| NF EN ISO 7731 : 2008 | ERGONOMICS - DANGER SIGNALS FOR PUBLIC AND WORK AREAS - AUDITORY DANGER SIGNALS |
| NF EN ISO 10218-1 : 2011 | ROBOTS AND ROBOTIC DEVICES - SAFETY REQUIREMENTS FOR INDUSTRIAL ROBOTS - PART 1: ROBOTS |
| NF EN 60825-4 : 2006 AMD 2 2011 | SAFETY OF LASER PRODUCTS - PART 4: LASER GUARDS |
| NF EN ISO 12100-1 : 2004 AMD 1 2009 | SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 1: BASIC TERMINOLOGY, METHODOLOGY |
| NF EN 61496-3 : 2002 | SAFETY OF MACHINERY - ELECTRO-SENSITIVE PROTECTIVE EQUIPMENT - PART 3: PARTICULAR REQUIREMENTS FOR ACTIVE OPTO-ELECTRONIC PROTECTIVE DEVICES RESPONSIVE TO DIFFUSE REFLECTION (AOPDDR) |
| NF EN 626-1 : 1994 + A1 2008 | SAFETY OF MACHINERY - REDUCTION OF RISK TO HEALTH FROM HAZARDOUS SUBSTANCES EMITTED BY MACHINERY - PART 1: PRINCIPLES AND SPECIFICATIONS FOR MACHINERY MANUFACTURERS |
| NF EN ISO 11064-1 : 2001 | ERGONOMIC DESIGN OF CONTROL CENTRES - PART 1: PRINCIPLES FOR THE DESIGN OF CONTROL CENTRES |
| NF EN ISO 14122-4 : 2017 | SAFETY OF MACHINERY - PERMANENT MEANS OF ACCESS TO MACHINERY - PART 4: FIXED LADDERS |
| R044-001 : 1999 | SAFETY OF MACHINERY - GUIDANCE AND RECOMMENDATIONS FOR THE AVOIDANCE OF HAZARDS DUE TO STATIC ELECTRICITY |
| NF EN 61310-2 : 2008 | SAFETY OF MACHINERY - INDICATION, MARKING AND ACTUATION - PART 2: REQUIREMENTS FOR MARKING |
| NF EN 12254 : 2010 | SCREENS FOR LASER WORKING PLACES - SAFETY REQUIREMENTS AND TESTING |
| NF EN 894-2 : 1997 + A1 2008 | SAFETY OF MACHINERY - ERGONOMICS REQUIREMENTS FOR THE DESIGN OF DISPLAYS AND CONTROL ACTUATORS - PART 2: DISPLAYS |
| NF EN ISO 11064-7 : 2006 | ERGONOMIC DESIGN OF CONTROL CENTRES - PART 7: PRINCIPLES FOR THE EVALUATION OF CONTROL CENTRES |
| NF EN ISO 11064-6 : 2005 | ERGONOMIC DESIGN OF CONTROL CENTRES - PART 6: ENVIRONMENTAL REQUIREMENTS FOR CONTROL CENTRES |
| NF EN 349 : 1993 + A1 2008 | SAFETY OF MACHINERY - MINIMUM GAPS TO AVOID CRUSHING OF PARTS OF THE HUMAN BODY |
| NF EN 1037 : 1996 + A1 2008 | SAFETY OF MACHINERY - PREVENTION OF UNEXPECTED START-UP |
| NF EN 1760-2 : 2001 + A1 2009 | SAFETY OF MACHINERY - PRESSURE SENSITIVE PROTECTIVE DEVICES - PART 2: GENERAL PRINCIPLES FOR THE DESIGN AND TESTING OF PRESSURE SENSING EDGES AND PRESSURE SENSITIVE BARS |
| NF EN 983 : 1996 + A1 2008 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR FLUID POWER SYSTEMS AND THEIR COMPONENTS - PNEUMATICS |
| NF EN 626-2 : 1996 + A1 2008 | SAFETY OF MACHINERY - REDUCTION OF RISK TO HEALTH FROM HAZARDOUS SUBSTANCES EMITTED BY MACHINERY - PART 2: METHODOLOGY LEADING TO VERIFICATION PROCEDURES |
| NF EN ISO 13850 : 2015 | SAFETY OF MACHINERY - EMERGENCY STOP FUNCTION - PRINCIPLES FOR DESIGN |
| NF EN 1127-1 : 2011 | EXPLOSIVES ATMOSPHERES - EXPLOSION PREVENTION AND PROTECTION - PART 1: BASIC CONCEPTS AND METHODOLOGY |
| NF EN 1032 : 2003 + A1 2009 | MECHANICAL VIBRATION - TESTING OF MOBILE MACHINERY IN ORDER TO DETERMINE THE VIBRATION EMISSION VALUE |
| NF EN 842 : 1996 + A1 2008 | SAFETY OF MACHINERY - VISUAL DANGER SIGNALS - GENERAL REQUIREMENTS, DESIGN AND TESTING |
| NF EN 61496-2 : 2014 | SAFETY OF MACHINERY - ELECTRO-SENSITIVE PROTECTIVE EQUIPMENT - PART 2: PARTICULAR REQUIREMENTS FOR EQUIPMENT USING ACTIVE OPTO-ELECTRONIC PROTECTIVE DEVICES (AOPDS) |
| NF EN ISO 15004-1 : 2009 | OPHTHALMIC INSTRUMENTS - FUNDAMENTAL REQUIREMENTS AND TEST METHODS - PART 1: GENERAL REQUIREMENTS APPLICABLE TO ALL OPHTHALMIC INSTRUMENTS |
| NF EN 12094-1 : 2003 | FIXED FIREFIGHTING SYSTEMS - COMPONENTS FOR GAS EXTINGUISHING SYSTEMS - PART 1: REQUIREMENTS AND TEST METHODS FOR ELECTRICAL AUTOMATIC CONTROL AND DELAY DEVICES |
| NF EN 1088 : 1996 + A2 2008 | SAFETY OF MACHINERY - INTERLOCKING DEVICES ASSOCIATED WITH GUARDS - PRINCIPLES FOR DESIGN AND SELECTION |
| FD ISO 7000 : 2004 FD | SYMBOLES GRAPHIQUES UTILISABLES SUR LE MATERIEL - INDEX ET TABLEAU SYNOPTIQUE |
| NF EN 689 : 1995 | WORKPLACE ATMOSPHERES - GUIDANCE FOR THE ASSESSMENT OF EXPOSURE BY INHALATION TO CHEMICAL AGENTS FOR COMPARISON WITH LIMIT VALUES AND MEASUREMENT STRATEGY |
| NF EN 999 : 1998 + A1 2008 | SAFETY OF MACHINERY - THE POSITIONING OF PROTECTIVE EQUIPMENT IN RESPECT OF APPROACH SPEEDS OF PARTS OF THE HUMAN BODY |
| NF EN ISO 11202 : 2010 | ACOUSTICS - NOISE EMITTED BY MACHINERY AND EQUIPMENT - DETERMINATION OF EMISSION SOUND PRESSURE LEVELS AT A WORK STATION AND AT OTHER SPECIFIED POSITIONS APPLYING APPROXIMATE ENVIRONMENTAL CORRECTIONS |
| NF EN 60825-1 : 2014 | SAFETY OF LASER PRODUCTS - PART 1: EQUIPMENT CLASSIFICATION AND REQUIREMENTS |
| NF EN 894-3 : 2000 + A1 2008 | SAFETY OF MACHINERY - ERGONOMICS REQUIREMENTS FOR THE DESIGN OF DISPLAYS AND CONTROL ACTUATORS - PART 3: CONTROL ACTUATORS |
| NF EN ISO 4871 : 2009 | ACOUSTICS - DECLARATION AND VERIFICATION OF NOISE EMISSION VALUES OF MACHINERY AND EQUIPMENT |
| NF EN 1299 : 1997 + A1 2009 | MECHANICAL VIBRATION AND SHOCK - VIBRATION ISOLATION OF MACHINES - INFORMATION FOR THE APPLICATION OF SOURCE ISOLATION |
| NF EN 61496-1 : 2014 | SAFETY OF MACHINERY - ELECTRO-SENSITIVE PROTECTIVE EQUIPMENT - PART 1: GENERAL REQUIREMENTS AND TESTS |
| NF EN 13478 : 2002 + A1 2008 | SAFETY OF MACHINERY - FIRE PREVENTION AND PROTECTION |
| NF EN 1837 : 1999 + A1 2009 | SAFETY OF MACHINERY - INTEGRAL LIGHTING OF MACHINES |
| NF EN 981 : 1997 + A1 2008 | SAFETY OF MACHINERY - SYSTEM OF AUDITORY AND VISUAL DANGER AND INFORMATION SIGNALS |
| NF EN 614-2 : 2000 + A1 2008 | SAFETY OF MACHINERY - ERGONOMIC DESIGN PRINCIPLES - PART 2: INTERACTIONS BETWEEN THE DESIGN OF MACHINERY AND WORK TASKS |
| NF EN ISO 11064-3 : 2000 | ERGONOMIC DESIGN OF CONTROL CENTRES - PART 3: CONTROL ROOM LAYOUT |
| NF EN ISO 11064-2 : 2001 | ERGONOMIC DESIGN OF CONTROL CENTRES - PART 2: PRINCIPLES FOR THE ARRANGEMENT OF CONTROL SUITES |
| NF EN ISO 11064-5 : 2008 | ERGONOMIC DESIGN OF CONTROL CENTRES - PART 5: DISPLAYS AND CONTROLS |
| NF EN 894-1 : 1997 + A1 2008 | SAFETY OF MACHINERY - ERGONOMICS REQUIREMENTS FOR THE DESIGN OF DISPLAYS AND CONTROL ACTUATORS - PART 1: GENERAL PRINCIPLES FOR HUMAN INTERACTIONS WITH DISPLAYS AND CONTROL ACTUATORS |
| NF EN 1248 : 2002 + A1 2009 | FOUNDRY MACHINERY - SAFETY REQUIREMENTS FOR ABRASIVE BLASTING EQUIPMENT |
| NF EN ISO 13849-1 : 2016 | SAFETY OF MACHINERY - SAFETY-RELATED PARTS OF CONTROL SYSTEMS - PART 1: GENERAL PRINCIPLES FOR DESIGN |
| NF EN ISO 14122-1 : 2017 | SAFETY OF MACHINERY - PERMANENT MEANS OF ACCESS TO MACHINERY - PART 1: CHOICE OF FIXED MEANS AND GENERAL REQUIREMENTS OF ACCESS |
| 1998/37/EC : 1998 | DIRECTIVE 98/37/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 22 JUNE 1998 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES RELATING TO MACHINERY |
| NF EN ISO 14122-3 : 2017 | SAFETY OF MACHINERY - PERMANENT MEANS OF ACCESS TO MACHINERY - PART 3: STAIRS, STEPLADDERS AND GUARD-RAILS |
| NF EN ISO 14121-1 : 2007 | SAFETY OF MACHINERY - RISK ASSESSMENT - PART 1: PRINCIPLES |
| NF EN 982 : 1996 + A1 2008 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR FLUID POWER SYSTEMS AND THEIR COMPONENTS - HYDRAULICS |
| NF EN ISO 12100-2 : 2004 AMD 1 2009 | SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 2: TECHNICAL PRINCIPLES |
| NF EN ISO 11064-4 : 2014 | ERGONOMIC DESIGN OF CONTROL CENTRES - PART 4: LAYOUT AND DIMENSIONS OF WORKSTATIONS |
| NFX 08 003-1 : 2006 | GRAPHICAL SYMBOLS - SAFETY COLOURS AND VISUAL SAFETY SIGNS - PART 1: DESIGN PRINCIPLES |
| NF EN ISO 11688-1 : 2009 | ACOUSTICS - RECOMMENDED PRACTICE FOR THE DESIGN OF LOW-NOISE MACHINERY AND EQUIPMENT - PART 1: PLANNING |
| NF EN 953 : 1997 + A1 2009 | SAFETY OF MACHINERY - GUARDS - GENERAL REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF FIXED AND MOVABLE GUARDS |
| NF EN 614-1 : 2006 + A1 2009 | SAFETY OF MACHINERY - ERGONOMIC DESIGN PRINCIPLES - PART 1: TERMINOLOGY AND GENERAL PRINCIPLES |
| NF EN 12198-3 : 2003 + A1 2008 | SAFETY OF MACHINERY - ASSESSMENT AND REDUCTION OF RISKS ARISING FROM RADIATION EMITTED BY MACHINERY - PART 3: REDUCTION OF RADIATION BY ATTENUATION OR SCREENING |
Summarise
Sorry this product is not available in your region.