NF ISO 8015 : 2006
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
TECHNICAL DRAWINGS - FUNDAMENTAL TOLERANCING PRINCIPLE
Published date
12-01-2013
Publisher
Superseded date
01-08-2011
Superseded by
Sorry this product is not available in your region.
Le principe spécifié doit être appliqué sur les dessins techniques et les documents connexes aux: - cotes linéaires et à leurs tolérances; - cotes angulaires et à leurs tolérances; - tolérances géométriques;qui définissent, pour chaque élément d'une pièce, les quatre aspects suivants: - dimension; - forme; - orientation; - position.
| DevelopmentNote |
Indice de classement: E04-561 PR NF ISO 8015 October 2005. (10/2005) Supersedes NFE 04 561 (02/2006)
|
| DocumentType |
Standard
|
| PublisherName |
Association Francaise de Normalisation
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| ISO 8015:2011 | Identical |
| NF EN 50377-8-13 : 2011 | CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 8-13: TYPE LSH-PC SIMPLEX TERMINATED ON IEC 60793-2-50 CATEGORY B1.1 AND B1.3 SINGLEMODE FIBRE WITH TITANIUM COMPOSITE FERRULE FOR CATEGORY U |
| NF EN 50377-4-2 : 2011 | CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 4-2: TYPE SC/APC SIMPLEX 8 DEGREES TERMINATED ON IEC 60793-2-50 OF TYPES B1.1 AND B1.3 SINGLEMODE FIBRE, WITH FULL ZIRCONIA FERRULE CATEGORY U |
| NF ISO 7388-2 : 2007 | TOOL SHANKS WITH 7/24 TAPER FOR AUTOMATIC TOOL CHANGERS - PART 2: DIMENSIONS AND DESIGNATION OF SHANKS OF FORMS J, JD AND JF |
| NF EN 50377-8-11 : 2011 | CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 8-11: TYPE LSH-PC SIMPLEX TERMINATED ON IEC 60793-2-50 CATEGORY B1.1 AND B1.3 SINGLEMODE FIBRE WITH TITANIUM COMPOSITE FERRULE FOR CATEGORY C |
| NF EN 50377-13-2 : 2011 | CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 13-2: TYPE LX.5-PC DUPLEX TERMINATED ON IEC 60793-2-50 CATEGORY B1.1 AND B1.3 SINGLE MODE FIBRE, WITH FULL ZIRCONIA FERRULE CATEGORY U |
| NF EN 50377-8-12 : 2011 | CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 8-12: TYPE LSH-APC SIMPLEX TERMINATED ON IEC 60793-2-50 CATEGORY B1.1 AND B1.3 SINGLEMODE FIBRE WITH TITANIUM COMPOSITE FERRULE FOR CATEGORY U |
| NF ISO 10110-1 : 2006 | OPTICS AND PHOTONICS - PREPARATION OF DRAWINGS FOR OPTICAL ELEMENTS AND SYSTEMS - PART 1: GENERAL |
| NF EN 50377-8-10 : 2011 | CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 8-10: TYPE LSH-APC SIMPLEX TERMINATED ON IEC 60793-2-50 CATEGORY B1.1 AND B1.3 SINGLEMODE FIBRE WITH TITANIUM COMPOSITE FERRULE FOR CATEGORY C |
| NF EN 50377-13-3 : 2011 | CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 13-3: TYPE LX.5-APC DUPLEX TERMINATED ON IEC 60793-2-50 CATEGORY B1.1 AND B1.3 SINGLE MODE FIBRE, WITH FULL ZIRCONIA FERRULE CATEGORY U |
| ISO 2692:2014 | Geometrical product specifications (GPS) — Geometrical tolerancing — Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR) |
| ISO 1101:2017 | Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out |
| ISO 286-1:2010 | Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes — Part 1: Basis of tolerances, deviations and fits |
Summarise
Sorry this product is not available in your region.