06/30151382 DC : DRAFT JUN 2006
Withdrawn
Withdrawn
BS ISO/IEC 24702 - INFORMATION TECHNOLOGY - GENERIC CABLING - INDUSTRIAL PREMISES
Published date
11-23-2012
Publisher
Withdrawn date
07-23-2013
Sorry this product is not available in your region.
| Committee |
TCT/7
|
| DocumentType |
Draft
|
| PublisherName |
British Standards Institution
|
| Status |
Withdrawn
|
| IEC 60794-3:2014 | Optical fibre cables - Part 3: Outdoor cables - Sectional specification |
| IEC 60512-11-4:2002 | Connectors for electronic equipment - Tests and measurements - Part 11-4: Climatic tests - Test 11d: Rapid change of temperature |
| IEC 60512-8:1993 | Electromechanical components for electronic equipment; basic testing procedures and measuring methods - Part 8: Connector tests (mechanical) and mechanical tests on contacts and terminations |
| IEC 60512-11-9:2002 | Connectors for electronic equipment - Tests and measurements - Part 11-9: Climatic tests - Test 11i: Dry heat |
| IEC 60512-11-10:2002 | Connectors for electronic equipment - Tests and measurements - Part 11-10: Climatic tests - Test 11j: Cold |
| IEC 60512-4-2:2002 | Connectors for electronic equipment - Tests and measurements - Part 4-2: Voltage stress tests - Test 4b: Partial discharge |
| IEC 60793-1-44:2011 | Optical fibres - Part 1-44: Measurement methods and test procedures - Cut-off wavelength |
| IEC 60793-1-41:2010 | Optical fibres - Part 1-41: Measurement methods and test procedures - Bandwidth |
| IEC 60512-6-3:2002 | Connectors for electronic equipment - Tests and measurements - Part 6-3: Dynamic stress tests - Test 6c: Shock |
| IEC 60793-2-30:2015 | Optical fibres - Part 2-30: Product specifications - Sectional specification for category A3 multimode fibres |
| IEC 60794-1-2:2017 | Optical fibre cables - Part 1-2: Generic specification - Basic optical cable test procedures - General guidance |
| ISO/IEC 11801:2002 | Information technology — Generic cabling for customer premises |
| IEC 60793-2-40:2015 | Optical fibres - Part 2-40: Product specifications - Sectional specification for category A4 multimode fibres |
| IEC 61156-5-1:2009 | Multicore and symmetrical pair/quad cables for digital communications - Part 5-1: Symmetrical pair/quad cables with transmission characteristics up to 1 000 MHz - Horizontal floor wiring - Blank detail specification |
| ISO/IEC TR 14763-2:2000 | Information technology — Implementation and operation of customer premises cabling — Part 2: Planning and installation of copper cabling |
| IEC 61156-6-1:2009 | Multicore and symmetrical pair/quad cables for digital communications - Part 6-1: Symmetrical pair/quad cables with transmission characteristics up to 1 000 MHz - Work area wiring - Blank detail specification |
| IEC 61918:2013 | Industrial communication networks - Installation of communication networks in industrial premises |
| IEC 60512-6-2:2002 | Connectors for electronic equipment - Tests and measurements - Part 6-2: Dynamic stress tests - Test 6b: Bump |
| ISO/IEC 18010:2002 | Information technology — Pathways and spaces for customer premises cabling |
| IEC 60793-1-40:2001 | Optical fibres - Part 1-40: Measurement methods and test procedures - Attenuation |
| ISO/IEC 14763-1:1999 | Information technology — Implementation and operation of customer premises cabling — Part 1: Administration |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| IEC 61076-3-106:2006 | Connectors for electronic equipment - Product requirements - Part 3-106: Rectangular connectors - Detail specification for protective housings for use with 8-way shielded and unshielded connectors for industrial environments incorporating the IEC 60603-7 series interface |
| IEC 60512-11-7:2003 | Connectors for electronic equipment - Tests and measurements - Part 11-7: Climatic tests - Test 11g: Flowing mixed gas corrosion test |
| IEC 61935-1:2015 | Specification for the testing of balanced and coaxial information technology cabling - Part 1: Installed balanced cabling as specified in ISO/IEC 11801 and related standards |
| ISO/IEC TR 14763-3:2000 | Information technology — Implementation and operation of customer premises cabling — Part 3: Acceptance testing for optical cabling |
| IEC 60512-19-3:1997 | Electromechanical components for electronic equipment - Basic testing procedures and measuring methods - Part 19: Chemical resistance tests - Section 3: Test 19c - Fluid resistance |
| IEC 60793-2-50:2015 | Optical fibres - Part 2-50: Product specifications - Sectional specification for class B single-mode fibres |
| IEC 60512-11-12:2002 | Connectors for electronic equipment - Tests and measurements - Part 11-12: Climatic tests - Test 11m: Damp heat, cyclic |
| IEC 60512-4-1:2003 | Connectors for electronic equipment - Tests and measurements - Part 4-1: Voltage stress tests - Test 4a: Voltage proof |
| IEC 60512-9:1992 | Electromechanical components for electronic equipment; basic testing procedures and measuring methods - Part 9: Miscellaneous tests |
| IEC 60794-2:2017 | Optical fibre cables - Part 2: Indoor cables - Sectional specification |
| IEC 61076-2-101:2012 | Connectors for electronic equipment - Product requirements - Part 2-101: Circular connectors - Detail specification for M12 connectors with screw-locking |
| IEC 61935-2:2010 | Specification for the testing of balanced and coaxial information technology cabling - Part 2: Cords as specified in ISO/IEC 11801 and related standards |
| IEC 60512-23-3:2000 | Electromechanical components for electronic equipment - Basic testing procedures and measuring methods - Part 23-3: Test 23c: Shielding effectiveness of connectors and accessories |
| IEC 61754-20:2012 | Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 20: Type LC connector family |
| IEC 60512-6-4:2002 | Connectors for electronic equipment - Tests and measurements - Part 6-4: Dynamic stress tests - Test 6d: Vibration (sinusoidal) |
| IEC 61753-053-3:2004 | Fibre optic interconnecting devices and passive components performance standard - Part 053-3: Continuously variable attenuators for category U - Uncontrolled environment |
Summarise
Sorry this product is not available in your region.