11/30235009 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
BS EN 13852-1 - CRANES - OFFSHORE CRANES - PART 1: GENERAL PURPOSE OFFSHORE CRANES
Hardcopy , PDF
10-31-2013
English
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and/or protective measures
6 Verification of the safety requirements and/or
protective measures
7 Information for use
Annex A (informative) - Selection of a suitable set
of crane standards for a given application
Annex B (normative) - Determination of factors
Annex C (normative) - Environmental influences
Annex D (normative) - Failure mode analysis
Annex E (normative) - Material selection
Annex F (normative) - Control station instrumentation
Annex G (normative) - Wire rope safety factors
Annex H (normative) - Slewing bearings
Annex I (normative) - Requirements for brakes
Annex J (normative) - Ranking of safety systems
Annex K (normative) - Required performance levels (PLr) for
SRP/CS according to EN ISO 13849-1:2008
Annex L (informative) - Typical general-purpose offshore
cranes and terminology
Annex M (normative) - Design excursion envelopes
Annex N (normative) - Noise test code
Annex O (normative) - Equipment for use in a hazardous area
Annex ZA (informative) - Relationship between this
European Standard and the Essential
Requirements of EU Directive 2006/42/EC
BS EN 13852-1
Committee |
MHE/3/10
|
DocumentType |
Draft
|
Pages |
92
|
PublisherName |
British Standards Institution
|
Status |
Superseded
|
SupersededBy |
Standards | Relationship |
PREN 13852-1 : DRAFT 2011 | Identical |
EN 1127-1:2011 | Explosive atmospheres - Explosion prevention and protection - Part 1: Basic concepts and methodology |
EN 12385-2:2002+A1:2008 | Steel wire ropes - Safety - Part 2: Definitions, designation and classification |
EN 12385-4:2002+A1:2008 | Steel wire ropes - Safety - Part 4: Stranded ropes for general lifting applications |
CEN/TS 13001-3-1:2004/AC:2006 | CRANES - GENERAL DESIGN - PART 3-1: LIMIT STATES AND PROOF OF COMPETENCE OF STEEL STRUCTURES |
EN 894-3:2000+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 3: Control actuators |
EN 13557:2003+A2:2008 | Cranes - Controls and control stations |
EN 982:1996+A1:2008 | Safety of machinery - Safety requirements for fluid power systems and their components - Hydraulics |
ISO 4871:1996 | Acoustics — Declaration and verification of noise emission values of machinery and equipment |
EN 12385-1:2002+A1:2008 | Steel wire ropes - Safety - Part 1: General requirements |
EN 10025-4:2004 | Hot rolled products of structural steels - Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels |
ISO 12480-1:1997 | Cranes Safe use Part 1: General |
EN 12644-2:2000+A1:2008 | Cranes - Information for use and testing - Part 2: Marking |
EN 60079-1:2014 | Explosive atmospheres - Part 1: Equipment protection by flameproof enclosures "d" |
ISO/TR 11688-1:1995 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning |
ISO 9374-4:1989 | Cranes Information to be provided Part 4: Jib cranes |
EN 61310-2:2008 | Safety of machinery - Indication, marking and actuation - Part 2: Requirements for marking |
EN 60079-0:2012/A11:2013 | EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS (IEC 60079-0:2011, MODIFIED) |
EN 14502-1:2010 | Cranes - Equipment for the lifting of persons - Part 1: Suspended baskets |
EN 12385-3:2004+A1:2008 | Steel wire ropes - Safety - Part 3: Information for use and maintenance |
EN 60079-15:2010 | Explosive atmospheres - Part 15: Equipment protection by type of protection "n" |
EN ISO 14121-1:2007 | Safety of machinery - Risk assessment - Part 1: Principles (ISO 14121-1:2007) |
EN 13463-1:2009 | Non-electrical equipment for use in potentially explosive atmospheres - Part 1: Basic method and requirements |
EN 13135-2:2004+A1:2010 | Cranes - Equipment - Part 2: Non-electrotechnical equipment |
ISO 12478-1:1997 | Cranes Maintenance manual Part 1: General |
EN 61310-3:2008 | Safety of machinery - Indication, marking and actuation - Part 3: Requirements for the location and operation of actuators |
EN ISO 13850:2015 | Safety of machinery - Emergency stop function - Principles for design (ISO 13850:2015) |
ISO 8566-1:2010 | Cranes Cabins and control stations Part 1: General |
ISO 9927-1:2013 | Cranes — Inspections — Part 1: General |
EN 13586:2004+A1:2008 | Cranes - Access |
EN ISO 7731:2008 | Ergonomics - Danger signals for public and work areas - Auditory danger signals (ISO 7731:2003) |
EN 50017:1998 | Electrical apparatus for potentially explosive atmospheres - Powder filling "q" |
EN 614-1:2006+A1:2009 | Safety of machinery - Ergonomic design principles - Part 1: Terminology and general principles |
EN 13411-3:2004+A1:2008 | Terminations for steel wire ropes - Safety - Part 3: Ferrules and ferrule-securing |
EN ISO 11688-2 : 2000 | ACOUSTICS - RECOMMENDED PRACTICE FOR THE DESIGN OF LOW-NOISE MACHINERY AND EQUIPMENT - PART 2: INTRODUCTION TO THE PHYSICS OF LOW-NOISE DESIGN |
EN 10025-1:2004 | Hot rolled products of structural steels - Part 1: General technical delivery conditions |
EN 12644-1:2001+A1:2008 | Cranes - Information for use and testing - Part 1: Instructions |
ISO 9374-1:1989 | Cranes Information to be provided Part 1: General |
EN 13411-7:2006+A1:2008 | Terminations for steel wire ropes - Safety - Part 7: Symmetric wedge socket |
EN 60204-32:2008 | Safety of machinery - Electrical equipment of machines - Part 32: Requirements for hoisting machines |
EN ISO 11201:2010 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections (ISO 11201:2010) |
EN 60079-11:2012 | Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i" |
EN 13001-2:2014 | Crane safety - General design - Part 2: Load actions |
EN 13135-1:2003+A1:2010 | Cranes - Equipment - Part 1: Electrotechnical equipment |
EN ISO 12100-1:2003/A1:2009 | SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 1: BASIC TERMINOLOGY, METHODOLOGY |
EN 60079-25:2010/AC:2013 | EXPLOSIVE ATMOSPHERES - PART 25: INTRINSICALLY SAFE ELECTRICAL SYSTEMS (IEC 60079-25:2010) |
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
EN 13001-1:2015 | Cranes - General design - Part 1: General principles and requirements |
EN ISO 3744:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010) |
EN 953:1997+A1:2009 | Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards |
EN 842:1996+A1:2008 | Safety of machinery - Visual danger signals - General requirements, design and testing |
EN 61000-6-4:2007/A1:2011 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-4: GENERIC STANDARDS - EMISSION STANDARD FOR INDUSTRIAL ENVIRONMENTS |
EN 10025-5:2004 | Hot rolled products of structural steels - Part 5: Technical delivery conditions for structural steels with improved atmospheric corrosion resistance |
EN 13411-4:2011 | Terminations for steel wire ropes - Safety - Part 4: Metal and resin socketing |
EN 13411-6:2004+A1:2008 | Terminations for steel wire ropes - Safety - Part 6: Asymmetric wedge socket |
EN 10204:2004 | Metallic products - Types of inspection documents |
ISO 12100-2:2003 | Safety of machinery Basic concepts, general principles for design Part 2: Technical principles |
CEN/TS 13001-3-5:2010 | Cranes - General design - Part 3-5: Limit states and proof of competence of forged hooks |
EN ISO 12100-2:2003/A1:2009 | SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 2: TECHNICAL PRINCIPLES |
EN 10025-2:2004/AC:2005 | HOT ROLLED PRODUCTS OF STRUCTURAL STEELS - PART 2: TECHNICAL DELIVERY CONDITIONS FOR NON-ALLOY STRUCTURAL STEELS |
EN ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread (ISO 898-1:2013) |
EN 60079-14:2014/AC:2016 | EXPLOSIVE ATMOSPHERES - PART 14: ELECTRICAL INSTALLATIONS DESIGN, SELECTION AND ERECTION (IEC 60079-14:2013/COR1:2016) |
EN 10083-2:2006 | Steels for quenching and tempering - Part 2: Technical delivery conditions for non alloy steels |
EN 983:1996+A1:2008 | Safety of machinery - Safety requirements for fluid power systems and their components - Pneumatics |
EN 10025-6:2004+A1:2009 | Hot rolled products of structural steels - Part 6: Technical delivery conditions for flat products of high yield strength structural steels in the quenched and tempered condition |
ISO 12100-1:2003 | Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology |
ISO 13850:2015 | Safety of machinery Emergency stop function Principles for design |
EN ISO 4871:2009 | Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996) |
EN 50015:1998 | Electrical apparatus for potentially explosive atmospheres - Oil immersion "o" |
EN 1005-3:2002+A1:2008 | Safety of machinery - Human physical performance - Part 3: Recommended force limits for machinery operation |
ISO 899-1:2017 | Plastics — Determination of creep behaviour — Part 1: Tensile creep |
EN ISO 11688-1:2009 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995) |
ISO 13849-1:2015 | Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design |
EN 10025-3:2004 | Hot rolled products of structural steels - Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels |
ISO/TR 11688-2:1998 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 2: Introduction to the physics of low-noise design |
EN 61310-1:2008 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
IEC 61000-6-2 : 3.0:2016 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-2: GENERIC STANDARDS - IMMUNITY STANDARD FOR INDUSTRIAL ENVIRONMENTS |
ISO 12482-1:1995 | Cranes Condition monitoring Part 1: General |
ISO 11201:2010 | Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections |
CEN/TS 13001-3-2:2008 | Cranes - General design - Part 3-2: Limit states and proof of competence of wire ropes in reeving systems |
EN 1993-1-1:2005/A1:2014 | EUROCODE 3: DESIGN OF STEEL STRUCTURES - PART 1-1: GENERAL RULES AND RULES FOR BUILDINGS |
EN 60079-2:2014/AC:2015 | EXPLOSIVE ATMOSPHERES - PART 2: EQUIPMENT PROTECTION BY PRESSURIZED ENCLOSURE 'P' (IEC 60079-2:2014) |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.