PD CLC/TR 50426:2004
Current
The latest, up-to-date edition.
Assessment of inadvertent initiation of bridge wire electro-explosive devices by radio-frequency radiation. Guide
Hardcopy , PDF
English
03-10-2005
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviations
4.1 Modulation codes
4.2 Polarization codes
5 General considerations
5.1 Radio-frequency hazards
5.2 Philosophy of the systematic method of approach
5.3 Responsibility for the making the hazard assessment
5.4 Recommended practices for radio silence in offshore
operations
6 Transmitters and transmitter output parameters
6.1 Types of transmitters
6.2 Frequency range
6.3 Transmitter output power
6.4 Antenna gain
6.5 Modulation factors
6.5.1 General
6.5.2 Frequency modulation (FM)
6.5.3 Amplitude modulation (AM)
6.5.4 Single sideband (SSB) operation
6.5.5 Pulsed radar
7 Circuits for blasting and well perforation
7.1 General
7.2 Typical blasting circuit layouts
7.2.1 General
7.2.2 Extended line blasts
7.2.3 Benching or 3-dimensional blasts
7.2.4 Multipattern blasts
7.2.5 Shaft sinking
7.2.6 Demolition work
7.3 Circuits formed during well-perforating using wireline
8 Electro-explosive devices
8.1 General
8.2 Commercial EED
8.3 EED hazard threshold
8.4 Common mode operation
9 Methods of assessment for determining potential RF ignition
hazards on a site where EED are used
9.1 General
9.2 Basis of the theoretical assessment for land sites
9.2.1 General
9.3 Initial assessment for land sites
9.3.1 Initial assessment of the risk from a particular
transmitter site
9.3.2 Initial assessment for a particular site using EED
9.4 Full assessment procedure for land sites
9.4.1 Procedure
9.4.2 Information to be obtained
9.4.3 Calculation of effective field strength
9.5 Safe field strength
9.5.1 General
9.5.2 Single EED
9.5.3 Single EED with extended leading wires
9.5.4 EED in typical quarry/demolition firing circuits
9.5.5 EED in well-perforating drilling operations
9.6 Multiple transmissions
9.6.1 General
9.6.2 Multiple-transmission assessment for
quarry/demolition sites
9.6.3 Multiple-transmission assessment for
well-perorating drilling operations
9.7 Assessment for offshore drilling operations
10 Practical on-site testing
11 Safety procedures
11.1 General procedures
11.2 Alternatives means of firing
12 Special applications
12.1 Semi-permanent installations
12.2 Flammable hazard of situations
12.3 Use of transmitters in mines and quarries
12.4 Safety in transit
Annex A (informative) Extraction of energy from the
electromagnetic field
Annex B (informative) Measurement of electromagnetic fields
Annex C (informative) Sources of information and address of
advisory bodies - UK ONLY
Annex D (informative) Electromagnetic radiated fields and
examples of radiating antennas and unintended receiving
antenna characteristics
Annex E (informative) The effective resistance of the leading
wires of an EED
Annex F (informative) Derivation of minimum distances of safe
approach for Table 2 and Table 3
Annex G (informative) Ground-wave propagation (vertical
polarization): calculation of field strength
Annex H (informative) Worked examples to demonstrate the effects
of antenna gain
Annex I (informative) The effects of leading wire resistance,
safely resistors and the use of EED with different
characteristics
Annex J (informative) Derivation of Figure 12a) to Figure 12g)
for EED alone incorporating the resistance of leading
wires and safety resistances
Bibliography
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.