DIN EN 15316-4-7:2009-02
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
HEATING SYSTEMS IN BUILDINGS - METHOD FOR CALCULATION OF SYSTEM ENERGY REQUIREMENTS AND SYSTEM EFFICIENCIES - PART 4-7: SPACE HEATING GENERATION SYSTEMS, BIOMASS COMBUSTION SYSTEMS
Hardcopy , PDF
09-01-2017
English
01-01-2009
National Foreword
Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions, symbols and units
3.1 Terms and definitions
3.2 Symbols and units
4 Principle of the method
4.1 Heat balance of the biomass combustion
sub-system, including control of heat
generation
4.1.1 Physical factors for biomass combustion
sub-system (biomass boiler) taken into
account
4.1.2 Calculation structure (input and output data)
4.2 Generation sub-system basic energy balance
4.3 Auxiliary energy
4.4 Recoverable, recovered and unrecoverable system
thermal losses
4.5 Calculation steps
4.6 Using net or gross calorific values
4.7 Boundaries between distribution and generation
sub-system
5 Biomass combustion sub-system calculation
6 Calculation method for boilers with automatic stocking
7 Calculation method for boilers with stocking by hand
7.1 Available methodologies
7.2 Operation periods
7.2.1 General
7.2.2 Heating up operation cycle
7.2.3 Boiler heating operation cycle
7.2.4 Cooling down operation cycle
7.2.5 Boiler non operation cycle
7.3 Case specific boiler efficiency method
7.3.1 Principle of the method
7.3.2 Input data to the method
7.3.3 Load of the boiler
7.3.4 Biomass boiler thermal losses
7.3.5 Total auxiliary energy
7.3.6 Recoverable generation system thermal losses
7.3.7 Fuel input
7.3.8 Operating temperature of the biomass boiler
7.4 Boiler cycling method
7.4.1 Principle of the method
7.4.2 Input data for the calculation method
7.4.3 Load factor
7.4.4 Specific thermal losses
7.4.5 Total thermal losses
7.4.6 Auxiliary energy
7.4.7 Recoverable system thermal losses
7.4.8 Calculation procedure for a modulating biomass
boiler (fan assisted)
Annex A (informative) - Additional formulas and default values
for parametering the case specific boiler efficiency
method
A.1 Information on the method
A.1.1 Basic assumptions and intended use
A.1.2 Known approximations
A.2 Boiler efficiencies and stand-by heat losses
A.2.1 Default values for boiler efficiency at full
load and intermediate load as a function of
the boiler power output
A.2.2 Stand-by heat losses
A.2.3 Correction factor taking into account variation
of efficiency depending on boiler average water
temperature
A.3 Auxiliary energy
A.4 Recoverable boiler thermal losses
A.4.1 Auxiliary energy
A.4.2 Thermal losses (boiler envelope)
A.4.3 Default data according to boiler location
Annex B (informative) - Additional formulas and default values
for parametering the boiler cycling method
B.1 Information on the method
B.1.1 Basis assumptions and intended use
B.1.2 Known approximations
B.2 Default specific losses
B.2.1 Default data for calculation of thermal losses
through the chimney with boiler on
B.2.2 Default values for calculation of thermal losses
through the boiler envelope
B.2.3 Default values for calculation of thermal losses
through the chimney with the boiler off
B.3 Default values for calculation of auxiliary energy
B.4 Additional default data for modulating burners
Annex C (informative) - Storage systems for biomass combustion
systems
C.1 General
C.1.1 Accumulator storage system
C.1.2 Load balancing storage system
C.2 Sizing of storage systems for biomass combustion systems
C.2.1 Sizing of the volume of the accumulator storage tank
C.2.2 Sizing of the volume of the load balancing tank
C.3 System thermal losses of storage systems
C.3.1 Thermal losses
C.3.2 Auxiliary energy of the circulation pump
Annex D (informative) - Calculation procedure with an example
for biomass boiler with stocking by hand - Case
specific boiler efficiency method
Annex E (informative) - Calculation procedure with an example
for biomass boiler with stocking by hand (Cycling
method)
Bibliography
National Annex NA (informative) - Bibliography
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.