VDI/VDE 2617 Blatt 2.1:2014-03
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Accuracy of coordinate measuring machines - Parameters and their reverification - Code of practice for the application of DIN EN ISO 10360-2 for length measurement
Hardcopy , PDF
05-04-2019
English, German - English
03-01-2014
Preliminary note
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Alterations in DIN EN ISO 10360-2:2010
5 Testing the length measurement
error as per DIN EN ISO 10360-2
6 Large coordinate measuring machines
Bibliography
Pertains to terminology used in the context of acceptance and reverification testing of coordinate measuring machines.
DevelopmentNote |
Supersedes VDI/VDE 2617-2-3. (03/2014)
|
DocumentType |
Standard
|
Pages |
20
|
PublisherName |
Verlag des Vereins Deutscher Ingenieure
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
VDI/VDE 2617 Blatt 6.3:2008-12 | Accuracy of coordinate measuring machines - Characteristics and their checking - Coordinate measuring machines with multiple probing systems |
VDI/VDE 2617 Blatt 6.1:2007-05 | Accuracy of coordinate measuring machines - Characteristics and their testing - Coordinate measuring machines with optical probing - Code of practice for the application of DIN EN ISO 10360 to coordinate measuring machines with optical sensors for lateral structures |
VDI/VDE 2617 Blatt 7:2008-09 | Accuracy of coordinate measuring machines - Parameters and their checking - Estimation of measurement uncertainty of coordinate measuring machines by means of simulation |
VDI/VDE 2617 Blatt 5:2010-12 | Accuracy of coordinate measuring machines - Parameters and their reverification - Interim check with artefacts |
VDI/VDE 2630 Blatt 1.4:2010-06 | Computed tomography in dimensional metrology - Measurement procedure and comparability |
VDI/VDE 2629 Blatt 2:2012-06 | Accuracy of contour-measuring systems - Characteristics and their checking - Determination of the uncertainty of specific contour measurements using standards/calibrated workpieces |
VDI/VDE 2617 Blatt 9:2009-06 | Accuracy of coordinate measuring machines - Characteristics and their reverification - Acceptance and reverification tests for Articulated Arm Coordinate Measuring Machines |
VDI/VDE 2617 Blatt 13; VDI/VDE 2630 Blatt 1.3:2011-12 | VDI/VDE 2617 Blatt 13: Accuracy of coordinate measuring machines - Characteristics and their testing - Guideline for the application of DIN EN ISO 10360 for coordinate measuring machines with CT-sensors - VDI/VDE 2630 Blatt 1.3: Computed tomography in dimensional measurement - Guideline for the application of DIN EN ISO 10360 for coordinate measuring machines with CT-sensors |
VDI/VDE 2617 Blatt 11:2011-03 | Accuracy of coordinate measuring machines - Characteristics and their checking - Determination of the uncertainty of measurement for coordinate measuring machines using uncertainty budgets |
VDI/VDE 2617 Blatt 5.1:2011-01 | Accuracy of coordinate measuring machines - Parameters and their reverification - Interim check with ball plates |
VDI/VDE 2629 Blatt 1:2008-08 | Accuracy of contour-measuring systems - Characteristics and checking of characteristics - Acceptance testing and reverification testing of contour-measuring systems according to the tactile stylus method |
DIN EN ISO 1:2015-03 (Draft) | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - STANDARD REFERENCE TEMPERATURE FOR THE SPECIFICATION OF GEOMETRICAL AND DIMENSIONAL PROPERTIES (ISO 1:2016) |
VDI/VDE 2617 Blatt 13; VDI/VDE 2630 Blatt 1.3:2011-12 | VDI/VDE 2617 Blatt 13: Accuracy of coordinate measuring machines - Characteristics and their testing - Guideline for the application of DIN EN ISO 10360 for coordinate measuring machines with CT-sensors - VDI/VDE 2630 Blatt 1.3: Computed tomography in dimensional measurement - Guideline for the application of DIN EN ISO 10360 for coordinate measuring machines with CT-sensors |
EN ISO 10360-1:2000/AC:2002 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - ACCEPTANCE AND REVERIFICATION TESTS FOR COORDINATE MEASURING MACHINES (CMM) - PART 1: VOCABULARY |
EN ISO 3650:1998 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - LENGTH STANDARDS - GAUGE BLOCKS |
DIN EN ISO 10360-1:2003-07 | Geometrical Product Specifications (GPS) - Acceptance and reverification tests for coordinate measuring machines (CMM) - Part 1: Vocabulary (ISO 10360-1:2000 + Corr 1:2002) (includes Corrigendum AC:2002); German version EN ISO 10360-1:2000 + AC:2002 |
VDI/VDE 2617 Blatt 6:1997-12 | Accuracy of coordinate measuring machines; characteristic parameters and their checking - Coordinate measuring machines with optical probes - Basics |
DIN ISO/TS 23165:2008-08 | |
ISO 1:2016 | Geometrical product specifications (GPS) Standard reference temperature for the specification of geometrical and dimensional properties |
DIN EN ISO 14253-1:2013-12 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - INSPECTION BY MEASUREMENT OF WORKPIECES AND MEASURING EQUIPMENT - PART 1: DECISION RULES FOR PROVING CONFORMITY OR NONCONFORMITY WITH SPECIFICATIONS (ISO 14253-1:2013) |
ISO 14253-1:2017 | Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 1: Decision rules for verifying conformity or nonconformity with specifications |
VDI/VDE 2617 Blatt 9:2009-06 | Accuracy of coordinate measuring machines - Characteristics and their reverification - Acceptance and reverification tests for Articulated Arm Coordinate Measuring Machines |
ISO 3650:1998 | Geometrical Product Specifications (GPS) Length standards Gauge blocks |
VDI/VDE 2617 Blatt 2.2:2000-07 | Accuracy of coordinate measuring machines - Parameters and their reverification - Form measurement |
DIN EN ISO 10360-2:2010-06 | Geometrical product specifications (GPS) - Acceptance and reverification tests for coordinate measuring machines (CMM) - Part 2: CMMs used for measuring linear dimensions (ISO 10360-2:2009) |
VDI/VDE 2617 Blatt 5:2010-12 | Accuracy of coordinate measuring machines - Parameters and their reverification - Interim check with artefacts |
VDI 1000:2017-02 | VDI Standardisation Work - Principles and procedures |
VDI/VDE 2627 Blatt 1:2015-12 | Measuring rooms - Classification and characteristics - Planning and execution |
VDI/VDE 2617 Blatt 7:2008-09 | Accuracy of coordinate measuring machines - Parameters and their checking - Estimation of measurement uncertainty of coordinate measuring machines by means of simulation |
DIN EN ISO 10360-5:2011-01 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - ACCEPTANCE AND REVERIFICATION TESTS FOR COORDINATE MEASURING MACHINES (CMM) - PART 5: CMMS USING SINGLE AND MULTIPLE STYLUS CONTACTING PROBING SYSTEMS |
VDI/VDE 2617 Blatt 6.3:2008-12 | Accuracy of coordinate measuring machines - Characteristics and their checking - Coordinate measuring machines with multiple probing systems |
VDI/VDE 2617 Blatt 10:2011-01 | Accuracy of coordinate measuring machines - Characteristics and their checking - Acceptance and reverification tests of lasertrackers |
EN ISO 10360-2:2009 | Geometrical product specifications (GPS) - Acceptance and reverification tests for coordinate measuring machines (CMM) - Part 2: CMMs used for measuring linear dimensions (ISO 10360-2:2009) |
VDI/VDE 2617 Blatt 5.1:2011-01 | Accuracy of coordinate measuring machines - Parameters and their reverification - Interim check with ball plates |
VDI/VDE 2617 Blatt 6.1:2007-05 | Accuracy of coordinate measuring machines - Characteristics and their testing - Coordinate measuring machines with optical probing - Code of practice for the application of DIN EN ISO 10360 to coordinate measuring machines with optical sensors for lateral structures |
VDI/VDE 2617 Blatt 8:2006-07 | Accuracy of coordinate measuring machines - Characteristics and their testing - Test suitability of measurements with coordinate measuring machines |
VDI/VDE 2617 Blatt 12.1:2011-03 | Accuracy of coordinate measuring machines - Characteristics and their checking - Acceptance and reverification tests for tactile CMM measuring microgeometries |
VDI/VDE 2617 Blatt 11:2011-03 | Accuracy of coordinate measuring machines - Characteristics and their checking - Determination of the uncertainty of measurement for coordinate measuring machines using uncertainty budgets |
EN ISO 10360-5:2010 | Geometrical product specifications (GPS) - Acceptance and reverification tests for coordinate measuring machines (CMM) - Part 5: CMMs using single and multiple stylus contacting probing systems (ISO 10360-5:2010) |
ISO 10360-5:2010 | Geometrical product specifications (GPS) Acceptance and reverification tests for coordinate measuring machines (CMM) Part 5: CMMs using single and multiple stylus contacting probing systems |
EN ISO 1:2016 (edition 2) | Geometrical product specifications (GPS) - Standard reference temperature for the specification of geometrical and dimensional properties (ISO 1:2016) |
ISO 10360-2:2009 | Geometrical product specifications (GPS) Acceptance and reverification tests for coordinate measuring machines (CMM) Part 2: CMMs used for measuring linear dimensions |
ISO/TS 23165:2006 | Geometrical product specifications (GPS) — Guidelines for the evaluation of coordinate measuring machine (CMM) test uncertainty |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.