AS 1341-1982

1 - AS 1341-1982 INFORMATION PROCESSING UNPPUNCHED PAPER TAPE
4 - PREFACE
4 - CONTENTS
5 - 1 SCOPE.
5 - 2 TEST CONDITIONS AND METHODS OF TEST
5 - 2.1 Sampling.
5 - 2.2 Test Conditions.
5 - 2.3 Conditioning of Test Samples.
5 - 2.4 Methods of Test.
5 - 3 DIMENSIONS
5 - 3.1 Width.
5 - 3.2 Thickness.
5 - 4 CHEMICAL PROPERTIES.
5 - 4.1 Hydrogen Ion Concentration.
5 - 4.2 Ash Content.
5 - 4.3 Grit Content.
5 - 4.4 Composition and Quality.
5 - 4.5 Chloride Content.
5 - 4.6 Sulphate Content.
5 - 4.7 Lubricating Additives.
5 - 5 PHYSICAL PROPERTIES.
5 - 5.1 Paper Grammage.
5 - 5.2 Strength.
5 - 5.2.1 Static tensile strength.
5 - 5.2.2 Internal tear resistance.
6 - 5.3 Dimensional Stability.
6 - 5.4 Folding Endurance.
6 - 5.5 Optical Properties.
6 - 5.6 Electrical Properties.
6 - 5.6.1 Bulk conductivity.
6 - 5.6.2 Surface resistivity limits.
6 - 5.7 Printability.
6 - 5.8 Colour.
6 - 5.9 Pre-printing.
6 - 5.10 Quality.
6 - 6 COILING OF UNPUNCHED TAPE.
6 - 6.1 Inner Diameter.
6 - 6.2 Outer Diameter.
6 - 6.3 End of Paper Tape Marker.
6 - 6.3.1 Warning mark.
6 - 6.3.2 Length of mark.
6 - 6.3.3 Colouring matter.
6 - 6.4 Pull-off Force.
6 - 6.5 Surface Finish.
6 - 6.6 Tightness of Coiling.
6 - 6.7 Length of Tape.
7 - APPENDIX A - METHOD FOR THE CONDITIONING OF PAPER TEST SAMPLES
7 - A1 SCOPE.
7 - A2 DEFINITIONS.
7 - A2.1 Relative Humidity (r.h.).
7 - A2.2 Conditioning.
7 - A3 PRINCIPLE.
7 - A4 CONDITIONING ATMOSPHERE.
7 - A5 EQUIPMENT.
7 - A5.1 Room and Measuring Instrumentation.
7 - A5.2 Determination of Temperature and Relative Humidity.
7 - A6 PROCEDURE.
7 - A6.1 Preliminary Treatment of Sampl es.
7 - A6.2 Conditioning.
7 - A7 TEST REPORT.
8 - APPENDIX B - DIMENSIONS
8 - B1 MEASUREMENT OF WIDTH.
8 - B2 MEASUREMENTOFTHICKNESS.
8 - B2.1 General.
8 - B2.2 Dial Micrometer Characteristics.
8 - B2.3 Calibration.
8 - B2.4 Sampling.
8 - B2.5 Test Procedure.
8 - B2.6 Results.
9 - APPENDIX C - DETERMINATION OF ASH
9 - C1 DEFINITION.
9 - C2 APPARATUS.
9 - C3 SAMPLING.
9 - C4 PREPARATION OF TEST PIECE.
9 - C5 PROCEDURE.
9 - C6 EXPRESSION OF RESULTS.
10 - APPENDIX D - DETERMINATION OF GRIT CONTENT
10 - D1 GENERAL.
10 - D2 DETERMINATION OF ABRASIVE GRIT.
10 - APPENDIX E - DETERMINATIONOFOILCONTENT
11 - APPENDIX F - DETERMINATION OF DIMENSIONAL STABILITY
11 - F1 SCOPE.
11 - F2 TEST ATMOSPHERE.
11 - F2.1 Test Temperature.
11 - F2.2 Length Measurements.
11 - F2.3 Atmospheric Conditions of Testing.
11 - F3 TEST PARAMETERS.
11 - F4 TEST REPORT.
12 - APPENDIX G - DETERMINATION OF LIGHT TRANSMISSION AND NOISE FACTOR
12 - G1 INTRODUCTION.
12 - G2 APPARATUS.
12 - G2.1 General.
12 - G2.2 The Light Source.
12 - G2.3 The Optical Path.
12 - G2.4 The Paper.
12 - G2.5 The Photocell.
12 - G2.6 The Measuring Meter.
12 - G3 THE LIGHT-COLLECTING ELEMENTS.
12 - G4 TEST PROCEDURE AND CALCULATIONS.
14 - APPENDIX H - DETERMINATION OF SURFACE RESISTIVITY
14 - H1 PREPARATION OF TEST PIECES FOR MEASUREMENT.
14 - H2 MEASUREMENT OF SURFACE RESISTIVITY.
14 - H3 PRESENTATION OF RESULTS.
14 - APPENDIX J - APPLICATION OF STANDARD BY THE AUSTRALIAN DEPARTMENT OF DEFENCE
14 - J1 APPROVED ITEM NAME (AIN).
14 - J2 ENDORSEMENT.
14 - J3 APPLICABLE DOCUMENTS.
14 - J4 VARIATIONS FROM THE AUSTRALIAN STANDARD.
14 - J5 ORDERING DATA.

Specifies dimensions and properties of unpunched paper tape used for data interchange. Technically identical with ISO 1729. Methods of test are either given in appendices or prescribed by reference to AS 1301.

This standard specifies the physical properties of unpunched paper tape to be used for data interchange.