AS 1443-2004

1 - AS 1443-2004 CARBON AND CARBON-MANGANESE STEEL-COLD FINISHED BARS
4 - PREFACE
5 - CONTENTS
6 - 1 SCOPE
6 - 2 REFERENCED DOCUMENTS
7 - 3 DEFINITIONS
7 - 3.1 Bar
7 - 3.2 Bar conditions
7 - 3.2.1 Bright bars
7 - 3.2.2 Cold-sized bars
7 - 3.2.3 Peeled bars
7 - 3.3 Bar shapes
7 - 3.3.1 Flat bars (flats)
7 - 3.3.2 Hexagonal bars (hexagons)
7 - 3.3.3 Round bars (rounds)
7 - 3.3.4 Square bars (squares)
7 - 3.4 Fully killed steel
8 - 3.5 Merchant quality steel
8 - 3.6 Test batch
8 - 3.7 Test piece
8 - 3.8 Test sample
8 - 3.9 Test specimen
8 - 4 DESIGNATION
8 - 4.1 General
8 - 4.2 Steels supplied to chemical composition only
9 - 4.3 Steels supplied to chemical composition and mechanical properties
9 - 4.4 Austenitic grain size
9 - 5 CONDITION OF STEEL ON DELIVERY
9 - 5.1 General
9 - 5.2 Steel supplied to chemical composition
10 - 5.3 Steels supplied to chemical composition and mechanical properties
10 - 6 MATERIALS
10 - 6.1 Chemical composition
10 - 6.1.1 General
10 - 6.1.2 Cast analysis
10 - 6.1.3 Residual elements
10 - 6.1.4 Product analysis
10 - 6.2 Tensile test requirements
10 - 7 FREEDOM FROM DEFECTS
10 - 7.1 General
11 - 7.2 Bright bars
11 - 7.2.1 Cold-drawn and cold-rolled bars
11 - 7.2.2 Turned and polished or precision ground bars
11 - 7.3 Cold-sized or peeled bars
11 - 8 DIMENSIONAL TOLERANCES
11 - 9 TENSILE TEST
11 - 9.1 Condition of test samples
12 - 9.2 Sampling
12 - 9.3 Location and preparation of test pieces
12 - 9.4 Method of test
12 - 9.5 Retesting
12 - 10 ROUNDING OF TEST RESULT VALUES
12 - 10.1 General
13 - 10.2 Tensile test results
13 - 11 MARKING
21 - APPENDIX A - PURCHASING GUIDELINES
21 - A1 GENERAL
21 - A2 INFORMATION TO BE SUPPLIED BY THE PURCHASER
23 - APPENDIX B - MEANS FOR DEMONSTRATING COMPLIANCE WITH THIS STANDARD
23 - B1 SCOPE
23 - B2 STATISTICAL SAMPLING
23 - B3 PRODUCT CERTIFICATION
23 - B4 SUPPLIER'S QUALITY MANAGEMENT SYSTEM
24 - B5 OTHER MEANS OF ASSESSMENT
25 - APPENDIX C - REQUIREMENTS FOR MAXIMUM SURFACE IMPERFECTION DEPTH AND RECOMMENDED MACHINING ALLOWANCES

Specifies requirements for cold-finished carbon steel and carbon-manganese steel bars manufactured from hot-rolled bars and semifinished products for general engineering purposes.

This Standard specifies requirements for cold-finished carbon steel and carbon-manganese steel bars manufactured from hot-rolled bars and semifinished products (see AS 1442), for general engineering purposes. The Standard applies to steel supplied to specified chemical composition only or to specified chemical composition and mechanical properties. It permits the addition of elements, such as boron, and micro-alloying elements for the achievement of special properties. NOTES: 1 Advice and recommendations on information that should be supplied by the purchaser at the time of enquiry and order are given in Appendix A. 2 Alternative means for determining compliance with this Standard are given in Appendix B.

Originated as AS G17-1966.
Previous edition AS 1443-1994.
Fifth edition 2004.