AS 1448-2007
Withdrawn
Carbon steel and carbon-manganese steels - Forgings (ruling section 300 mm maximum)
Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users
05-22-2007
06-30-2017
Specifies the requirements for carbon steel and carbon-manganese steel forgings for general engineering purposes with ruling section up to and including 300 mm.
| Committee |
MT-001
|
| DocumentType |
Standard
|
| ISBN |
0 7337 8247 7
|
| Pages |
13
|
| ProductNote |
Withdrawn 28-06-2017.
|
| PublisherName |
Standards Australia
|
| Status |
Withdrawn
|
| Supersedes |
This Standard specifies requirements for carbon steel and carbon-manganese steel forgings for general engineering purposes with ruling section up to and including 300 mm. The Standard provides for the supply of forgings on the following basis:(a) Chemical composition only, as specified in Tables 1 to 4.(b) Chemical composition as specified in Tables 1 to 4, and hardness or other mechanical properties in any heat-treated condition, as negotiated at the time of enquiry and/or order.(c) Chemical composition and mechanical properties in the normalized or normalized and tempered condition as specified in Table 5.NOTES:1 For guidance on purchasing requirements refer to Appendix A.2 To demonstrate a means of compliance to the Standard refer to Appendix B.
Originated as AS G30-1970.
Previous edition AS 1448-1981.
Third edition 2007.
| AS 1391-2007 | Metallic materials - Tensile testing at ambient temperature (Reconfirmed 2017) |
| AS/NZS 1554.4:2004 | Structural steel welding - Welding of high strength quenched and tempered steels |
| AS 2062-1997 | Non-destructive testing - Penetrant testing of products and components |
| AS/RISSB 7515 : 2014 | Railway Rolling Stock - Axles |
| AS/NZS 1554.6:1994 | Structural steel welding - Welding stainless steels for structural purposes |
| AS 1544.2-2003 | Method for impact tests on metals Charpy V-notch (Reconfirmed 2017) |
| AS 1391-2005 | Metallic materials - Tensile testing at ambient temperature |
| AS 2706-2003 | Numerical values - Rounding and interpretation of limiting values (Reconfirmed 2018) |
| AS 1171-1998 | Non-destructive testing - Magnetic particle testing of ferromagnetic products, components and structures (Reconfirmed 2022) |
| HB 18.28-2005 | Conformity assessment - Guidance on a third-party certification system for products |
| AS/NZS 1050.1:1996 | Methods for the analysis of iron and steel Sampling iron and steel for chemical analysis (Reconfirmed 2017) |
| AS/NZS 1050.16:1994 | Methods for the analysis of iron and steel Determination of sulfur content - Infrared absorption method after combustion in an induction furnace (Reconfirmed 2017) |
| AS 5016-2004 | Metallic materials - Conversion of hardness values |
| AS 1199.1-2003 | Sampling procedures for inspection by attributes Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection (Reconfirmed 2016) |
| AS/NZS 1050.18:1994 | Methods for the analysis of iron and steel Determination of phosphorus - Spectrophotometric method (Reconfirmed 2016) |
| AS 1817.1-2003 | Metallic materials - Vickers hardness test Test method (ISO 6507-1:1997, MOD) |
| AS/NZS 1050.14:1994 | Methods for the analysis of iron and steel Determination of manganese in iron and steel - Titrimetric method |
| AS/NZS ISO 9004:2000 | Quality management systems - Guidelines for performance improvements |
| AS/NZS 1554.1:2004 | Structural steel welding Welding of steel structures |
| AS/NZS ISO 9001:2000 | Quality management systems - Requirements |
| AS 1065-1988 | Non-destructive testing - Ultrasonic testing of carbon and low alloy steel forgings (Reconfirmed 2022) |
| AS 1816.1-2007 | Metallic materials - Brinell hardness test Test method (ISO 6506-1:2005, MOD) |
| AS 1199.0-2003 | Sampling procedures for inspection by attributes Introduction to the ISO 2859 attribute sampling system (Reconfirmed 2016) |
| AS/NZS 1554.7:2006 | Structural steel welding Welding of sheet steel structures |
| AS/NZS 1554.5:2004 | Structural steel welding Welding of steel structures subject to high levels of fatigue loading |
| AS/NZS 1554.3:2002 | Structural steel welding Welding of reinforcing steel |
| AS 1733-1976 | Methods for the determination of grain size in metals (Reconfirmed 2018) |
| AS/NZS 1554.2:2003 | Structural steel welding Stud welding (steel studs to steel) |
| AS 2740-2001 | Wedge-type sockets (Reconfirmed 2014) |
| AS 2938-1993 | Gears - Spur and helical - Guide to specification and rating |
| AS 1138-1992 | Thimbles for wire rope |
| AS 2089-1993 | Sheave blocks for lifting purposes |
| AS EN 12079.1-2010 | Offshore containers and associated lifting sets Offshore containers - Design, manufacture and marking (EN 12079-1:2006, MOD) |
| AS 1154.1-2009 | Insulator and conductor fittings for overhead power lines Performance, material, general requirements and dimensions (Reconfirmed 2019) |
| AS 3751-2005 | Underground mining - Slope haulage - Couplings, drawbars, and safety chains |
| AS 1418.1-2002 | Cranes, hoists and winches General requirements |
| AS 1085.2-2002 | Railway track material Fishplates (Reconfirmed 2013) |
| AS 4041-2006 | Pressure piping |
| AS 1154.1-2004 | Insulator and conductor fittings for overhead power lines - Performance, material, general requirements and dimensions |
| AS 3777-2008 | Shank hooks and large eye hooks - Maximum 60 t (Reconfirmed 2019) |
| AS 1735.1-2003 | Lifts, escalators and moving walks General requirements |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.