AS 4024.1201-2006

1 - AS 4024.1201-2006 SAFETY OF MACHINERY - GENERAL PRINCIPLES-BASIC TERMINOLOGY AND METHODOLOGY
4 - PREFACE
5 - CONTENTS
6 - 1 SCOPE
6 - 2 OBJECTIVE
6 - 3 REFERENCED DOCUMENTS
6 - 4 DEFINITIONS
6 - 4.1 Common cause failures
6 - 4.2 Common mode failures
7 - 4.3 Comparative emission data
7 - 4.4 Emergency operation
7 - 4.5 Emergency situation
7 - 4.6 Emergency stop
7 - 4.7 Emission value
7 - 4.8 Failure
7 - 4.9 Failure to danger
7 - 4.10 Fault
8 - 4.11 Guarding
8 - 4.11.1 Guard
8 - 4.11.2 Adjustable guard
8 - 4.11.3 Interlocking guard
8 - 4.11.4 Interlocking guard with a start function control guard
8 - 4.11.5 Interlocking guard with guard locking
8 - 4.11.6 Moveable guard
9 - 4.12 Harm
9 - 4.13 Hazard
9 - 4.14 Hazard zone, danger zone
9 - 4.15 Hazardous situation
9 - 4.16 Impeding device
9 - 4.17 Information for use
9 - 4.18 Inherently safe design measure
9 - 4.19 Intended use of a machine
9 - 4.20 Machinery, machine
10 - 4.21 Maintainability (of a machine)
10 - 4.22 Protective devices
10 - 4.22.1 Protective device
10 - 4.22.2 Active opto-electronic protective device (AOPD)
10 - 4.22.3 Enabling device
10 - 4.22.4 Hold-to-run control device
10 - 4.22.5 Interlocking device, interlock
10 - 4.22.6 Limited movement control device
10 - 4.22.7 Limiting device
10 - 4.22.8 Mechanical restraint device
10 - 4.22.9 Sensitive protective equipment (SPE)
10 - 4.22.10 Two-hand control device
11 - 4.23 Protective measure
11 - 4.24 Reasonably foreseeable misuse
11 - 4.25 Relevant hazard
11 - 4.26 Reliability (of a machine)
11 - 4.27 Residual risk
11 - 4.28 Risk
11 - 4.29 Risk analysis
11 - 4.30 Risk assessment
11 - 4.31 Risk estimation
11 - 4.32 Risk evaluation
11 - 4.33 Safeguard
12 - 4.34 Safeguarding
12 - 4.35 Safety function
12 - 4.36 Significant hazard
12 - 4.37 Unexpected start-up, unintended start-up
12 - 4.38 Useability (of a machine)
12 - 5 HAZARDS TO BE TAKEN INTO ACCOUNT WHEN DESIGNING MACHINERY
12 - 5.1 General
12 - 5.2 Mechanical hazard
12 - 5.2.1 Typical hazards
13 - 5.2.2 Contributing factors
13 - 5.3 Electrical hazard
13 - 5.4 Thermal hazard
14 - 5.5 Hazard generated by noise
14 - 5.6 Hazards generated by vibration
14 - 5.7 Hazards generated by radiation
14 - 5.8 Hazards generated by materials and substances
14 - 5.9 Hazards generated by neglecting ergonomic principles in machine design
15 - 5.10 Slipping, tripping and falling hazards
15 - 5.11 Hazard combinations
15 - 5.12 Hazards associated with the environment in which the machine is used
15 - 6 STRATEGY FOR RISK REDUCTION
15 - 6.1 General provisions
16 - 6.2 Specification of the limits of the machine
16 - 6.3 Hazard identification, risk estimation and risk evaluation
17 - 6.4 Elimination of hazards or reduction of risk by protective measures
18 - 6.5 Achievement of risk reduction objectives
21 - APPENDIX A - SCHEMATIC REPRESENTATION OF A MACHINE

Specifies the basic terminology and methodology to be used by designers in achieving safety of machinery.

This Standard defines the basic terminology and methodology used in achieving safety of machinery.The provisions stated in this Standard are intended for the designer.This Standard does not deal with injury or damage to domestic animals, property or the environment.

Originated as part of AS 4024.1(Int)-1992.
Previous edition part of AS 4024.1-1996.
Revised in part and redesignated as AS 4024.1201-2006.