• There are no items in your cart

AS/NZS 5601.1:2010

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Gas installations General installations

Available format(s)

Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users

Superseded date

05-29-2024

Published date

12-23-2010

Preview

Specifies requirements and means of compliance for the design, installation and commissioning of gas installations that are associated with use or intended use of fuel gases such as natural gas, LP Gas, biogas or manufactured gas.

Committee
AG-006
DocumentType
Standard
ISBN
978 0 7337 9742 2
Pages
219
PublisherName
Standards Australia
Status
Superseded
SupersededBy
Supersedes
UnderRevision

This Standard contains the mandatory requirements and means of compliance for the design, installation and commissioning of gas installations that are associated with the use or intended use of fuel gases such as natural gas, LP Gas, biogas or manufactured gas. The user is expected to be familiar with the properties and characteristics of those fuel gases and the principles of combustion, ventilation and flueing applicable to the safe installation and operation of gas appliances. For New Zealand, these requirements cover gas installations downstream of the point of supply (as defined in the Gas (Safety and Measurement) Regulations 2010.For Australia, these requirements cover gas installations downstream of the outlet of - (a) the consumer billing meter installation; (b) the first regulator on a fixed gas installation where an LP Gas tank or cylinder(s) is installed on site; or (c) the first regulator on site (if no meter is installed) where LP Gas is reticulated from off site storage.Where the term 'installation' is used it is deemed to include the pipework, appliances, flues, air ducts, ventilation and other ancillary items.Section 2 of this Standard contains the performance requirements for the design, installation, and commissioning of gas installations, including those operating at pressures exceeding 200 kPa. It includes, in Clause 2.6.4, some specific limitations as the performance requirements cannot be reliably met if those prohibitions are breeched.Sections 3 to 6 of this Standard contain a means of compliance for installations designed to operate with a gas supply pressure not exceeding 200 kPa. In Australia, approval for any variation to the requirements of Sections 3 to 6 or the normative appendices might need to be obtained from the appropriate Technical Regulator.In New Zealand, the Technical Regulator does not provide approvals for variations to the means of compliance in Sections 3 to 6. References to approval by the Technical Regulator are not applicable to New Zealand. The installation certifier is responsible for ensuring that the installation, including any variations, meets the requirements in Section 2.Where a Standard is cited as part of a means of compliance or in an Appendix, any Standard with equivalent performance requirements may be used as an alternative means of compliance in New Zealand.

First published as AS 5601/AG 601-2000.Second edition 2002.Revised and designated as AS 5601-2004.Jointly revised and redesignated AS/NZS 5601.1:2010. Originated in Australia as AS 5601/AG 601-2000. Previous Australian edition AS 5601-2004. Originated in New Zealand as NZS 5261:1996. Previous New Zealand edition NZS 5261:2003. Jointly revised and redesignated AS/NZS 5601.1:2010. Reissued incorporating Amendment No. 1 (August 2011).

AS/NZS 4645.1:2008 Gas distribution networks Network management
AS/NZS 1477:2006 PVC pipes and fittings for pressure applications
AS 3959-2009 Construction of buildings in bushfire-prone areas
AS 2738-2000 Copper and copper alloys - Compositions and designations of refinery products, wrought products, ingots and castings (Reconfirmed 2018)
AS 4621-2004 Regulators for use with liquefied petroleum - Vapour phase
AS 4176.1-2010 Multilayer pipes for pressure applications Multilayer piping systems for hot and cold water plumbing applications - General (ISO 21003-1:2008, MOD) (Reconfirmed 2022)
AS/NZS 1167.1:2005 Welding and brazing - Filler metals Filler metal for brazing and braze welding
AS/NZS 2648.1:1995 Underground marking tape Non-detectable tape (Reconfirmed 2020)
AS 1572-1998 Copper and copper alloys - Seamless tubes for engineering purposes (Reconfirmed 2018)
AS 4567-2005 Twin wall metal flues - Gas appliances (Reconfirmed 2017)
AS 4176.3-2010 Multilayer pipes for pressure applications Multilayer piping systems for hot and cold water plumbing applications - Fittings (ISO 21003-3:2008, MOD)
AS 4176.7-2010 Multilayer pipes for pressure applications Multilayer piping systems for hot and cold water plumbing applications - Assessment of conformity (ISO/TS 21003-7:2008, MOD)
AS/NZS 4645.2:2008 Gas distribution networks Steel pipe systems
AS 1074-1989 Steel tubes and tubulars for ordinary service (Reconfirmed 2018)
AS/NZS 1260:2009 PVC-U pipes and fittings for drain, waste and vent application
AS/NZS 60079.10.1:2009 Explosive atmospheres Classification of areas - Explosive gas atmospheres (IEC 60079-10-1, Ed.1.0(2008) MOD)
AS/NZS 1668.1:1998 The use of ventilation and airconditioning in buildings Fire and smoke control in multi-compartment buildings
AS 4617-2004 Manual shut off gas valves
AS 3688-2005 Water supply - Metallic fittings and end connectors
AS 4623-2008 Jointing compounds and materials for use in gas pipe joints
AS 4627-2005 Quick-connect devices for gas
AS/NZS 3000:2007 Electrical installations (known as the Australian/New Zealand Wiring Rules)
AS 1397-2001 Steel sheet and strip - Hot-dipped zinc-coated or aluminium/zinc-coated
AS/NZS 2208:1996 Safety glazing materials in buildings
AS 4176.2-2010 Multilayer pipes for pressure applications Multilayer piping systems for hot and cold water plumbing applications - Pipes (ISO 21003-2:2008, MOD) (Reconfirmed 2022)
AS 4176.8-2010 Multilayer pipes for pressure applications Multilayer pipe systems for consumer gas installations with a maximum operating pressure up to and including 5 bar (500 kPa) - Specifications for systems (ISO 17484-1:2006, MOD)
AS 2944.2-2007 Plastics pipes and fittings for gas reticulation Polyamide fittings (Reconfirmed 2023)
AS 4176.5-2010 Multilayer pipes for pressure applications Multilayer piping systems for hot and cold water plumbing applications - Fitness for purpose of the system (ISO 21003-5:2008, MOD) (Reconfirmed 2022)
AS 4631-2005 Limited flexibility connectors for gas
AS/NZS 4645.3:2008 Gas distribution networks Plastics pipe systems
AS ISO 6993.3-2007 Buried, high-impact poly(vinyl chloride) (PVC-HI) piping systems for the supply of gaseous fuels Fittings and saddles for a maximum operating pressure of 1 bar (100 kPa)
AS 4566-2005 Flue cowls - Gas appliances
AS ISO 6993.1-2007 Buried, high-impact poly(vinyl chloride) (PVC-HI) piping systems for the supply of gaseous fuels Pipes for a maximum operating pressure of 1 bar (100 kPa) (ISO 6993-1:2006, MOD)
AS 4041-2006 Pressure piping (Reconfirmed 2016)
AS 4553-2008 Gas space heating appliances
AS/NZS 1596:2008 The storage and handling of LP Gas
AS 2030.1-2009 Gas cylinders General requirements
AS 1530.1-1994 Methods for fire tests on building materials, components and structures Combustibility test for materials (Reconfirmed 2016)
AS ISO 7.1-2008 Pipe threads where pressure-tight joints are made on the threads Dimensions, tolerances and designation
AS D26-1972 Tube fittings with dryseal American standard taper pipe and unified threads for automotive and industrial use (imperial units) (Reconfirmed 2018)
AS 2944.1-2007 Plastics pipes and fittings for gas reticulation Polyamide pipes (Reconfirmed 2023)
AS/NZS 1869:1996 Hose and hose assemblies for liquefied petroleum gases (LP Gas), natural gas and town gas
AS/NZS 1530.3:1999 Methods for fire tests on building materials, components and structures Simultaneous determination of ignitability, flame propagation, heat release and smoke release (Reconfirmed 2016)
AS/NZS 4129:2008 Fittings for polyethylene (PE) pipes for pressure applications
AS/NZS 2918:2001 Domestic solid fuel burning appliances - Installation
AS 3673-1989 Malleable cast iron threaded pipe fittings
AS 2700-1996 Colour Standards for general purposes - Swatches
AS 10745-1998 Information technology - Open Systems Interconnection - Upper layers security model
AS 1357.1-2009 Valves primarily for use in heated water systems Protection valves
AS/NZS 4130:2009 Polyethylene (PE) pipes for pressure applications
AS 3814-2009 Industrial and commercial gas-fired appliances
AS/NZS 1734:1997 Aluminium and aluminium alloys - Flat sheet, coiled sheet and plate (Reconfirmed 2020)
AS 1210-2010 Pressure vessels (Reconfirmed 2021)
AS 1345-1995 Identification of the contents of pipes, conduits and ducts (Reconfirmed 2018)
AS 2129-2000 Flanges for pipes, valves and fittings (Reconfirmed 2016)
AS/NZS 1518:2002 External extruded high-density polyethylene coating system for pipes (Reconfirmed 2016)
AS 4629-2005 Automatic shut off valves and vent valves (Reconfirmed 2018)
AS 1432-2004 Copper tubes for plumbing, gasfitting and drainage applications

AS 5262-2011 LP Gas mobile industrial direct fired air heaters
AS/NZS 5601.2:2010
AS 4558-2011 Decorative gas log and other fuel effect appliances
AS 4556-2011 Indirect gas-fired ducted air heaters
AS 1668.4-2012 The use of ventilation and airconditioning in buildings Natural ventilation of buildings
AS/NZS 5601.2:2013 Gas installations LP Gas installations in caravans and boats for non-propulsive purposes
AS 5263.0-2013 Gas appliances General requirements

View more information
US$183.03
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.