• Shopping Cart
    There are no items in your cart

BS 5410-3:1976

Superseded

Superseded

View Superseded by

Code of practice for oil firing Installations for furnaces, kilns, ovens and other industrial purposes

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

11-30-1976

Superseded date

05-31-2016

Superseded by

BS 5410-3:2016

US$462.87
Excluding Tax where applicable
Summarise this standard

Foreword
Cooperating organizations
Code
1 Scope
2 References
3 Definitions
Section two. Liquid fuels
4 Types of petroleum oil fuels
5 Typical petroleum oil fuel characteristics
6 Storage and handling temperatures for petroleum oil
    fuels
7 Types of coal tar fuels
8 Typical coal tar fuel characteristics
Section three. Selection and application of oil burners
9 General
10 Choice of grade of fuel
11 Selection and application of burner types
12 Control of burners
13 Refractor lining and insulation of combustion
    chamber
14 Combustion and safety controls
Section four. Oil tanks and equipment
15 Construction
16 Capacity
17 Choice of number, siting and type of tank
18 Design and test conditions
19 Measurement of oil storage tank contents
20 Precautions against overfilling
21 Filling pipes and connections
22 Vent pipes
23 Drain valves
24 Intercoupling of small oil storage tanks (combined
    capacity not exceeding 5000 litres)
25 Multiple storage tanks with return line connections
26 Installations of oil storage tanks
27 Painting and cleaning
28 Heating of oil tanks
29 Tank thermal insulation
30 Auxiliary tanks including service tanks
Section five. Oil handling systems from storage tank
                to burner
31 General
32 Distillate fuel oil systems (classes C and D fuels)
33 Heated oil fuel systems (classes E, F, G and H)
34 Sizing of oil pipelines
Section six. Design and construction of accommodation
                for oil fired installations
35 General
36 Classification of industrial premises
37 Accommodation for furnaces
38 Accommodation for oil tanks
Section seven. Waste gas handling equipment
39 Chimneys
40 Flues
41 Dampers
42 Fans (induced draught or recirculation)
43 Ejectors
44 Means of heat recovery from waste gases
45 Gas cleaning equipment
Section eight. Electrical, control and instrumentation
                recommendations
46 General
47 Wiring
48 Motors and motor control gear
49 Automatic shut-off valves and manually operated
    isolating valves
50 Process regulated control devices
51 Valve actuators
52 Ignition equipment
53 Starting-up, shutting-down and flame monitoring
    control devices
54 Pressure indicators
55 Temperature indicators
56 Flow meters and flow indicators
57 Instrument and control panels
58 Proving devices
59 Control of oil heating
60 Safety control devices
Section nine. Commissioning
61 General
62 Precommissioning checks
63 Essential commissioning procedures
Section ten. Maintenance
64 General
65 Suppliers' and/or installers' responsibilities
66 User's responsibilities
Section eleven. Special factors relevant to change of
                fuel
67 General
68 Heat input required
69 Combustion chamber or combustion zone
70 Pressure in combustion chamber or combustion zone
71 Fans
72 Positioning of burners
73 Flues and chimneys
74 Potentialities of existing systems and controls
Section twelve. Essential safety requirements
75 Fire prevention
76 Safe routing of fuel pipelines and control systems
77 Isolating valves and emergency shut-off valves
78 Adequacy of air supply
79 Effectiveness of ignition source
80 Adequacy of visual supervision facilities
81 Adequate operating and maintenance instructions
82 Operator training
83 Arrangements of additional ventilation where
    flammable solvents are evaporated in furnaces
    (ovens)
84 Explosion relief
85 Provision of strong burner mountings and inspection
    doors, catches and hinges
86 Hazards from use of air filters and combustion
    systems
87 Hazards arising from accumulation of unburnt oil in
    furnace
Tables
1 Specification data for petroleum oil fuels as given
    in BS 2869 : 1970
2 Typical characteristics of petroleum oil fuels
    available in the United Kingdom
3 Minimum storage, outflow and handling temperatures
4 Specification data for coal tar fuels
5 Typical characteristics for coal tar fuels available
    in the United Kingdom
6 Recommended standards of fire resistance for tank
    chambers in buildings
Figure
1 Method of interconnecting two or more oil storage
    tanks by means of unvalved balance pipes and common
    fill, vent and outlet pipes

Recommendations for the selection, application and installation of burners, tanks, piping systems, accommodation, chimneys, electrical and control equipment; also for commissioning, maintenance, change of fuel and essential safety requirements.

Committee
RHE/13
DevelopmentNote
Supersedes BS CP3002-2(1964) (07/2004) Supersedes 75/70132 DC. (08/2005) Reviewed and confirmed by BSI, November 2008. (11/2008)
DocumentType
Standard
Pages
52
PublisherName
British Standards Institution
Status
Superseded
SupersededBy
Supersedes

⚠

A newer version of this standard is available.

View Current Edition
US$462.87
Excluding Tax where applicable