BS 5760-13.5:1996
Withdrawn
Reliability of systems, equipment and components. Guide to reliability test conditions for consumer equipment Ground mobile equipment. Low degree of simulation
Hardcopy , PDF
English
08-15-1996
10-26-2018
Committees responsible
National foreword
Introduction
Guide
1 Scope
2 Normative references
3 Definitions
4 Applicability
5 Basic assumptions concerning operational environment
6 Pre-exposure tests
7 Description of the test cycle
8 Relevant test time
Annex
A (informative) Bibliography
Tables
1 Climatic conditions encountered for a long period
of time
2 Examples of equipment
3 Climatic conditions according to IEC 721-2-1
4 Climatic conditions: externally carried equipment
5 Climatic conditions: internally carried equipment
6 Vibration test severities
Figure
1 Test cycle
Gives preferred test conditions as in 8.4 of IEC 605-1, which applies to direct current (d.c.) powered mobile equipment. This equipment is operated while being transported in or on a vehicle but is not part of the vehicle, and should not be installed permanently in a vehicle.
| Committee |
DS/1
|
| DevelopmentNote |
Also numbered as IEC 60605-3-5 Supersedes 94/408196 DC (08/2005)
|
| DocumentType |
Standard
|
| Pages |
18
|
| PublisherName |
British Standards Institution
|
| Status |
Withdrawn
|
| Supersedes |
| BS 5760-4:2003 | Reliability of systems, equipment and components Guide to the specification of dependability requirements |
| 03/101534 DC : DRAFT JAN 2003 | BS 5760-4 - RELIABILITY OF SYSTEMS, EQUIPMENT AND COMPONENTS - PART 4: GUIDE TO THE SPECIFICATION OF DEPENDABILITY REQUIREMENTS |
| BS EN 60068-2-6:2008 | Environmental testing Tests. Test Fc. Vibration (sinusoidal) |
| CISPR 12:2007+AMD1:2009 CSV | Vehicles, boats and internal combustion engines - Radio disturbance characteristics - Limits and methods of measurement for the protection of off-board receivers |
| BS AU 243-1:1991 | Methods of test for electrical disturbance by conduction and coupling General |
| IEC 60605-3-4:1992 | Equipment reliability testing - Part 3: Preferred test conditions - Section 4: Test cycle 4: Equipment for portable and non-stationary use - Low degree of simulation |
| BS AU 243-2:1991 | Methods of test for electrical disturbance by conduction and coupling Electrical transient conduction along supply lines only on passenger cars and light commercial vehicles with 12 V supply |
| IEC 60605-3-1:1986 | Equipment reliability testing. Part 3: Preferred test conditions. Indoor portable equipment - Low degree of simulation |
| BS 7527-2.1:1991 | Classification of environmental conditions. Environmental conditions appearing in nature Temperature and humidity |
| ISO/TR 10605:1994 | Road vehicles — Electrical disturbances from electrostatic discharge |
| BS 4778-3.2:1991 | Quality vocabulary. Availability, reliability and maintainability terms Glossary of international terms - 3.2 glossay of international terms |
| BS 2011-2.1N:1985 | Environmental testing. Tests Test N. Change of temperature |
| BS 5760-10.1:1993 | Reliability of systems, equipment and components. Guide to reliability testing General requirements |
| BS EN 60068-2-1:2007 | Environmental testing Tests. Test A. Cold |
| BS AU 243-3:1991 | Methods of test for electrical disturbance by conduction and coupling Electrical transient conduction along supply lines only on commercial vehicles with 24 V supply |
| BS EN 60721-3-5:1997 | Classification of environmental conditions. Classification of groups of environmental parameters and their severities Ground vehicle installations |
| IEC 60605-2:1994 | Equipment reliability testing - Part 2: Design of test cycles |
| BS EN 60068-2-2:2007 | Environmental testing Tests. Test B. Dry heat |
| BS EN 60068-2-64:1995 | Environmental testing. Test methods Test Fh. Vibration, broad-band random (digital control) and guidance |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.